Semtronics 62532 User manual

TB-6108 Page 1 of 9 Revision 07/05
© 2005 DESCO INDUSTRIES INC.
Employee Owned
62532 (EN649)
Ethernet Adapter
INSTALLATION AND OPERATING
INSTRUCTIONS
For sales and Service in
North America contact:
ESD Systems.com
www.esdsystems.com
[email protected]
Phone: [phone]
Fax: [phone]
Corporate Office:
3651 Walnut Avenue,
Chino, CA 91710
Phone: [phone]
Fax [phone]
For sales and service in Europe and
Asia contact:
OK International - European Headquarters
Eagle Close, Chandlers Ford,
Hampshire, SO53 4NF U.K. England
http://www.okintl.com/locations.htm
Tel: [phone]
Fax: [phone]

TB-6108 Page 2 of 9 Revision 07/05
© 2005 DESCO INDUSTRIES INC.
Employee Owned
Introduction:
The Semtronics 62532 Ethernet adapter provides an easy and effective means of retrieving
data from Semtronic’s 62580 and 62581 Smartlog X3 from anywhere within the LAN or from
any location in the world. By using the Semtronics 62532, the Smartlog X3 can be mounted
anywhere in the facility without the use of a dictated PC where a network port is accessible.
Specifications:
•Dimension: 6.4cm x 9.0cm x 2.3cm, 2.5”W x 3.5”D x 0.9”H
•Weight 0.8 lbs
•Universal powers supply with interchangeable outlet adapter. Input 110-230 VAC
50/60Hz. Output 12VDC/0.8A. 2.5mm female power jack, center positive. Any alternate
transformer must comply with the Safety Extra Lox Voltage (SELV) insulation
requirements.
Important: This appliance has a metal casing and is considered to be class I and tested
as class II. The power supply connection plug is accessible to the user and this no safety
insulation inside the 62532. Therefore the insulation of the power supply is critical.
•Rated power consumption: 3A maximum
PC Requirements:
Intel® Pentium® II or above processor. Operating platform, Windows®2000 (with service
pack 2)
Additional Software:
Lantronix redirector, compact redirector (red), downloaded from www.lantronix.com
Environmental Conditions:
Pollution degree 2 per IEC 644
Temperature:
Operating Range: 5 to 50 °C, 41 to 122 °F
Storage Range: -40 to 66 °C, -40 to151 °F
Maximum Temperature Change Per Hour: 20°C, 36°F
Note: Maximum temperature changes may affect operation, Therefore, do not operate the
unit near heating or cooling devices, large windows, or doors that opens to the outdoors.
Altitude:

TB-6108 Page 3 of 9 Revision 07/05
© 2005 DESCO INDUSTRIES INC.
Employee Owned
Operating: 2.4km, 8000ft
Storage: 9.1km, 30000ft
Note: If operating unit above 2.4km or 8000ft, decrease the operating temperature rating by 1
degree for every 1000ft.
Figure 1. Bottom View
Figure 2. Top View

TB-6108 Page 4 of 9 Revision 07/05
© 2005 DESCO INDUSTRIES INC.
Employee Owned
Current RS-232 Configuration (Use only when DB25 connector is labeled RS-232)
Figure 3. Connection Setup

TB-6108 Page 5 of 9 Revision 07/05
© 2005 DESCO INDUSTRIES INC.
Employee Owned
Previous RS-485 configuration (Old configuration, no label on DB25)
Figure 4. Connection Setup
A. Hardware Setup
1. Insert DB25 serial adapter to female DCE DB25 serial port of the 62532 Ethernet
adapter.
2. Connect cable from RJ11 jack of serial adapter to RS-485 port (left RJ11 port) of
Smartlog X3 (Refer to Figure 4). Connect to RS-232 port on RS-232 connector (figure 3)
only if labeled RS-232.

TB-6108 Page 6 of 9 Revision 07/05
© 2005 DESCO INDUSTRIES INC.
Employee Owned
3. Connect power adapter and network wires.
4. Before mounting 62532, MAC address located on back side needs to be noted for
proper programming of Ethernet adapter.
B. Assigning IP Address
1. Connect the 62532 to an Ethernet port within the LAN connection.
2. Power the unit on, the green LINK LED should be on, the red DIAGNOSTIC
LED should be flashing then off when the green STATUS LED comes on. The
orange NET Tx\Rx should be flashing.
3. On the same LAN connection, you’re going to need a PC to set and program
the 62532. Go to your Start icon in Taskbar of Windows®. Go to Run and type
in CMD and hit enter. This should take you to the Command Prompt. Type in
CD\ and hit enter to get to the root directory. (Figure 5).
Figure 5
4. Type: arp –s <IP address> <Physical address> and hit enter. The IP address
needs to be assigned by IT. The MAC address is located on the back of the
62532 ethernet adapter. (Figure 6)
Figure 6

TB-6108 Page 7 of 9 Revision 07/05
© 2005 DESCO INDUSTRIES INC.
Employee Owned
5. Let’s use 192.168.10.13 as an example IP address. Type in telnet
192.168.10.13 1 and hit enter, make sure you type in 1 for the port. It will
display “Could not open connection to host, or port 1: connection fail”.
6. Then Type in telnet 192.168.10.13 9999 and hit enter, you should now have
connection to the host, hit enter again to go into setup mode. (Figure 7)
Figure 7.
7. Enter 0 and Hit Enter for Server Configuration.
a. Assign IP Address: It will ask you to assign an IP address for the unit.
Have this IP address written down, you’re going to reference this IP
address later on.
b. Gate Address: Enter the Gate address If applicable. Enter N and hit
enter if you are going to use the 62532 on the same LAN as the PC
used to poll the data. For remote access not within the locate LAN,

TB-6108 Page 8 of 9 Revision 07/05
© 2005 DESCO INDUSTRIES INC.
Employee Owned
enter Y and enter the Gateway IP address, your IT department can
supply you with the appropriate Gateway IP address.
c. Netmask: Number of bits for host 11. Netmask defines the number of
bits taken from the IP address that are assigned for the host sections.
d. Change telnet configuration password: Enter N for no. Enter Y for
yes, then type in a 4-digit password. Changes can only be made to the
50460 with a password if password is set to Yes.
8. Enter 1 for Channel 1 Configuration.
a. Baudrate = 9600
b. I/F Mode = 5B (serial RS-485) / 58 (serial RS-232)
c. Flow = 0
d. Port No = 14001 or 1400X (x=1...9)
e. Connect Mode = C5
f. Remote IP address = 0
g. Remote port = 0
h. DisConn Mode = 0
i. Flush Mode = 0
j. DisconnTime = 0
k. SendChar 1 = 0
l. SendChar 2 = 0
Select 9 to save and exit. (Figure 10).
9. Verify the IP address:
•Go to the DOS prompt.
•Type: ping <IP address>.
•If there is a reply, then the IP address has been assigned successfully. If there
is no response, please go back to A.
C.Redirector Software Setup
Comport redirector will need to be downloaded from Lantronix ®.
Go to www.lantronix.com and downloads. Then scroll down to Software/Configuration
Utilities, you should see Com Port Redirector, click on the lastest version and start
downloading. Save it in your Smartlog™ Folder.
Once you are done downloading, Windows will ask you if you want to install it, click yes.
Once Installation is completed, open your Lantronix ® Com port Redirector.

TB-6108 Page 9 of 9 Revision 07/05
© 2005 DESCO INDUSTRIES INC.
Employee Owned
Figure 8. Lantronix RDCfg Main Menu
1. The software will default one open com port to be use, usually it’s com 3
if your PC system isn’t using com 3.
2. Click on Add IP
•Enter the IP address that was assigned to the Ethernet adapter
62532 in the box Host.
•Subtract 11000 from Port No. to get TCP Port, refer to 8. Enter 1
for Channel 1 Configuration. d. Usually TCP Port 3001
•Click Ok, save and eixt.
3. Open the software you are currently using or Smartlog 6.03 and configure your
comport in the software to match the comport of the Lantronix Redirector
software.

TB-6108 Page 10 of 9 Revision 07/05
© 2005 DESCO INDUSTRIES INC.
Employee Owned
TECHNICAL SUPPORT:
USA
Semtronics
3651 Walnut Avenue
Chino, CA 91710
Tel: [phone]
Fax: [phone]
NOTE: Unauthorized servicing or modifications to your monitor will void the product warranty
and may create dangerous conditions. Servicing should be performed only at the factory, or
by a Semtronics approved technician.
LIMITED WARRANTY
Semtronics expressly warrants that for a period of one (1) year from the date of purchase Semtronics
62532 will be free of defects in material (parts) and workmanship (labor). Within the warranty period,
a unit will be tested, repaired, or replaced at our option, free of charge. Call Customer Service at 909-
627-8178 (Chino, CA) or 781-821-8370 (Canton, MA) for Return Material Authorization (RMA) and
proper shipping instructions and address. Include a copy of your original packing slip, invoice, or other
proof of date of purchase. Any unit under warranty should be shipped prepaid to the Semtronics
factory. Warranty replacements will take approximately two weeks.
If your unit is out of warranty, Semtronics will quote repair charges necessary to bring your unit up to
factory standards. Call Customer Service at 909-627-8178 for proper shipping instructions and
address. Ship your unit freight prepaid.
WARRANTY EXCLUSIONS
THE FOREGOING EXPRESS WARRANTY IS MADE IN LIEU OF ALL OTHER PRODUCT
WARRANTIES, EXPRESSED AND IMPLIED, INCLUDING MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE WHICH ARE SPECIFICALLY DISCLAIMED. The express warranty will
not apply to defects or damage due to accidents, neglect, misuse, alterations, operator error, or failure
to properly maintain, clean or repair products.
LIMIT OF LIABILITY
In no event will Semtronics or any seller be responsible or liable for any injury, loss or damage, direct
or consequential, arising out of the use of or the inability to use the product. Before using, users shall
determine the suitability of the product for their intended use, and users assume all risk and liability
whatsoever in connection therewith.