Sencor SES 9300BK Repair manual

EN FULLY AUTOMATIC ESPRESSO/
CAPPUCCINO MACHINE
Translation of the original manual
SES 9300BK
SES 9301WH

SES 9300BK
SES 9301WH

A
1
2
3
4
5
6
7
8
9
10
11
12
13
14

B
Espresso Cappuccino Latte
Americano Coffee Hot Water
Frother Clean Brewer Clean
Descaling Water Filter
123 4 5 6 7 8 9
10 11 12 13 14 15 16
17
18
19
20
C D
E1 E2

E3 E4
E5 E6
E7

- 1 - 06/2023
2023, .
EN Fully Automatic Espresso / Cappuccino
Machine
Important Safety Instructions
READ CAREFULLYAND STORE FOR FUTURE USE.
• This appliance is not to be used by children. Keep this
appliance and its power cord out of the reach of children.
• The appliance may be used by persons with reduced
physical, sensory or mental abilities or lack of experience
and knowledge, provided they are supervised or have
been instructed in the safe use of the appliance and
understand the potential hazards.
• Children must not play with the appliance.
• Cleaning and maintenance performed by the user must
not be performed by children.
• If the power cord is damaged, have it replaced in a
professional service centre in order to prevent a dangerous
situation. It is forbidden to use the appliance with the
power cord damaged.
• Always clean the parts of the appliance that come into
contact with food with clean warm water and a little neutral
dishwashing liquid, rinse them with clean water and wipe
dry.
WARNING:
Incorrect use may lead to injury.

- 2 - 06/2023
2023, .
Always disconnect the appliance from the power supply
when leaving it unattended and before assembly,
disassembly or cleaning.
This appliance is intended for use in the home.
It is not intended for use in areas such as:
• kitchenettes in shops, offices and other workplaces;
• agriculture;
• by guests in hotels, motels and other residential areas;
• bed and breakfast establishments.
WARNING:
Avoid spilling on the plug.
WARNING:
The outer surface of the appliance heats up during
use and may be hot for some time after use. Be very
careful.
The appliance must not be placed in a cabinet when in use.
WARNING:
The filling hole must not be opened during use.
Do not do submerge the power cord, plug or
appliance in water or any other liquid.
Electrical Safety
• Before connecting the appliance to a power outlet, make sure that its nominalvoltage indicated on the rating plate matches the electrical voltage of
the socket.
• Connect the appliance only to a properly grounded socket. For safety reasons, we don’t recommend using adaptor plugs or extension cords.
• Do not place the appliance on windowsills, sink drain trays or unstable surfaces. Always place the appliance on a stable, flat and dry surface.
• Do not place the appliance on an electric or gas stove or near an open flame.
• Never use the appliance in the immediate vicinity of a bath, shower or swimming pool.
• Use the appliance only for the purpose for which it has been designed.
• Use the appliance according to the instructions in this user manual. Otherwise injury, damage to the appliance or dangerous situation might occur.
• Only use the appliance with the original accessories supplied with it.
• During operation, a clear space of at least 15 cm must be left around and above the appliance to ensure sufficient air circulation.
• Do not place any items on the top surface of the appliance.
• Fill the water tank with clean, cold water. Do not pour hot water or other liquids into it or place any objects inside it.

- 3 - 06/2023
2023, .
–the drip tray with grid is installed in its place;
–the water tank is filled with a sufficient amount of water and is properly installed in its position;
–the bean hopper is filled with fresh coffee beans.
Safety in Use
• The water level must not exceed the maximum mark.
• Take extra care when operating the appliance to avoid scalding with hot water or steam.
• The hot water function may only be used continuously for a maximum of one emptying of the entire water tank.
• When using the appliance, check the water level in the water tank regularly. If the water level falls below the minimum mark, refill the water tank.
Before adding water, first turn off the appliance and disconnect it from the power socket.
• Use the built-in coffee grinder only for grinding coffee beans. Do not use it for any other purposes.
• Ensure that no hair or other items enter the grinder area during the grinding process. The coffee bean hopper lid should always be properly closed
unless you are refilling coffee beans or adjusting the grinding coarseness.
• The appliance is equipped with a built-in thermal fuse that shuts it off when the pump is idling to prevent damage. If such asituation occurs, unplug
the power cord and allow the appliance to cool down for at least 30 minutes. Then you can use it again.
• Do not move the appliance with a coffee cup located on the grid of the drip tray.
• Ensure that the power cord does not come into contact with a hot surface.
• Unplug the appliance from the power socket by pulling the plug, not the power cord. Otherwise, damage to the power cord or the socket may occur.
• Do not submerge the appliance, power cord or plug in water or any other liquid.
• Make sure that the power cord and plug does not come into contact with water or other fluid.
• To avoid the danger of injury by electrical shock, do not repair or modify the appliance yourself. Have all repairs or adjustments performed at an
authorised service centre. By tampering with the appliance, you expose yourself to the risk of losing your legal rights regarding faulty performance
or warranty for quality.

- 4 - 06/2023
2023, .
• Thank you for purchasing our SENCOR product; we hope you will be
satisfied with it.
• Before using this appliance, please familiarise yourself with the user
manual, even if you are already familiar with using similar types of
appliances. Use the appliance only as described in this user manual.
Keep the manual for future reference.
• For the duration of the legal rights regarding faulty performance or
warranty for quality, we recommend keeping the original packaging,
packaging materials, receipt, and proof of the seller'sliability or
warranty certificate. When transporting the appliance, we recommend
packaging it again in the original box provided by the manufacturer.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DESCRIPTION OF THE APPLIANCE
A1 Grinding coarseness regulator
A2 Ground coffee hopper
A3 Ground coffee hopper cover
A4 Control panel
A5 Coffee spout head (height is
adjustable)
A6 Milk Container
A7 Coffee grounds container
A8 Bean hopper lid
A9 Water tank, capacity 1.4 l
A10 Coffee bean hopper
Inside the hopper there is
agrinder with adjustable
grinding coarseness
A11 Power cord
A12 Drip tray
A13 Drip tray cover
A14 Grid
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DESCRIPTION OF THE CONTROLPANEL
B1 Button : coffee machine
power on/off
B2 Icon : ground coffee
brewing function icon
B3 Button : adjusting the
amount of ground coffee
B4 Button : coffee quantity
setting
B5 Button Espresso: start
brewing espresso
B6 Button Cappuccino: start
brewing cappuccino
B7 Button Latte: start brewing
latte
B8 Button : flush milk
container
B9 Button : cleaning the
brewing system
B10 Button : adjust the amount
of milk foam
B11 Button : adjust preset
temperature
B12 Button Americano: start
brewing americano
B13 Button Coffee: start brewing
coffee
B14 Button Hot Water: hot water
dispensing
B15 Button : start the descaling
process
B16 Button : change water filter
B17 Indicator light : warning for
empty water tank
B18 Indicator light : warning for
full coffee grounds container
B19 Indicator light : warning for
empty bean hopper
B20 Indicator light : warning
for incorrectly installed milk
container
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BEFORE FIRST USE
• Before first use, remove the appliance and its accessories form the
packaging and remove all promotional labels and tags. Check that
neither the appliance nor any of its components is damaged.
• Install the appliance on an even, dry and clean surface.
• Remove the water tank, rinse it with clean water and asmall amount
of neutral kitchen detergent. Then rinse it properly with clean water,
dry it and put it back in place.
• Secure the outer drip tray properly to the appliance.
• Wipe the outer surface of the appliance with aslightly damp cloth and
then wipe dry properly.
• Fully unwind the detachable power cord and connect it to the
corresponding socket at the back of the appliance.
Filling the Water Tank
1. Hold the water tank by its lid. This also serves as acarrying handle.
Lift it up and remove it from the back of the appliance.
2. Fill the water tank with clean water up to the maximum mark and
insert it back into the appliance. Make sure that the water tank is
properly installed in its place.
Note:
The water that you pour into the water tank should
ideally be at room temperature (approximately 25°C).
Water that is too cold can adversely affect the final
taste of the coffee drink.
Warning:
The maximum capacity of the water tank is 1.4 l of
water. Do not overfill it.
Never fill the water tank with warm or hot water,
sparkling water or other liquids such as milk. This
could damage the appliance.
Never fill the water tank by pouring water into in while
it is inserted inside the appliance. There is arisk of
spilling the appliance or overfilling the water tank.
3. Do not leave water in the water tank for more than one day. For
brewing quality fresh coffee, it is necessary to always use fresh
water. Otherwise, the taste of the resulting beverage may be
adversely affected.
Note:
Awater filter can be installed in the water tank.
This is not included. We recommend using water
filters for espresso machines. Follow the water filter
manufacturer'sinstructions, especially regarding use
and replacement.
Filling the Bean Hopper
1. Remove the bean hopper lid.
2. Pour roasted coffee beans into the bean hopper and close the lid.
Do not leave the lid of the bean hopper open, otherwise the coffee
beans will lose their aroma more quickly.
Warning:
Themaximum capacity of the hopper is 200 g of
coffee beans. Do not overfill it.
Never fill the bean hopper with ground or instant
coffee, caramelised or otherwise specially treated
coffee beans, cocoa beans or other items that may
cause damage to
the appliance.
Grinding Coarseness Regulator
Use the grinding coarseness regulator to adjust the appropriate
coarseness of the ground coffee. Only adjust the grinding coarseness
when the grinder is running. The new coarseness will be reflected on
the second or third coffee preparation since the grinding coarseness was
changed.
1. You can adjust the coarseness of the grinding in 9 levels by using
the grinding coarseness regulator, which is located inside the bean
hopper (Figure C).
2. Turn the regulator clockwise to set acoarser grind, turn
counterclockwise to set afiner grind.
3. Only adjust the grinding coarseness when the grinder is running.
Otherwise, damage to the appliance could occur. For darker
beans we recommend setting acoarser grind, for lighter beans we
recommend setting afiner grind.
4. If the brewed coffee flows out very slowly, it means that the beans
are ground too finely and acoarser grind should be set. On the other
EN
Fully Automatic Espresso / Cappuccino Machine
User Manual

- 5 - 06/2023
2023, .
hand, if the brewed coffee flows out too fast, it means that the grains
are ground too coarsely and afiner grind should be set.
Note:
Darker roasted beans require afiner degree of
grinding coarseness, while lighter roasted beans
require acoarser degree of grinding coarseness.
Milk Container
• If you are going to make alatte, cappuccino or need to froth milk, take
the milk container out of the machine and fill it with fresh, cold milk.
Then put it back into the coffee machine (picture D).
• Always fill below the maximum level. The maximum capacity of the
milk container is 250 ml.
Note:
If the milk container is installed in the machine,
the Frother Clean indicator light will be on. This is
anormal occurrence.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
USING THE COFFEE MACHINE
• Place the coffee machine on aflat, dry and clean surface at
asufficient distance from the from the power socket. Ensure there is
enough space around it for manipulation, at least 15 cm around the
entire coffee machine.
• Make sure that the water tank is refilled with fresh water and that the
bean hopper has an adequate amount of coffee beans and that the
appliance is properly assembled.
• Plug the power cord connector into the socket in the coffee machine
and connect the power cord plug to the power socket.
• The control panel is equipped with touch buttons. Use the bellies
of your fingers to press the buttons, not the tips. When pressing, it
is important to ensure constant finger contact with the button. Do
not push the button with force. Press the button where its symbol is
located.
Note:
When refilling water and coffee beans, always follow the
instructions provided in chapter “Filling the Water Tank”
and “Filling the Bean Hopper”.
Coffee Machine Power On/Off
• Long press the button (3 seconds) to switch on the coffee
machine. Button indicator light will flash.
• The coffee machine starts heating up, and the preparation process
begins, during which water is pumped into the internal circuit, the
grinder is checked, and the coffee spout is rinsed, with asmall amount
of water flowing into the cup. During this time, the grinder and pump
will briefly operate. This is anormal occurrence.
• As soon as all the buttons light up, the machine is ready for use.
• When you have finished using the machine, long press the button
(3 seconds) to switch off the machine.
Note:
The coffee machine is equipped with an automatic shut-off
function. The automatic shut-off occurs after the set period
of being idle – see the section “Automatic Shut-off of
the Coffee Machine” later in the manual. This is anormal
occurrence.
Water Hardness Settings
• The water hardness will need to be adjusted the first time the machine
is switched on, or when switching on after the factory settings have
been made.
• The water hardness is factory set to 4.
• You can find out the hardness of the water either by asking your
drinking water supplier or by taking awater hardness test by dipping
atest strip into the water. Water hardness test kit not included.
• We recommend that you set the water hardness correctly according
to how hard you will use the water in the machine. This will ensure
proper operation of the machine, descaling intervals and prolong its
life.
• Long press the button to enter the water hardness setting mode,
then press the button repeatedly to set the desired water
hardness from 1 to 4. The corresponding number of indicator lights
will illuminate.
• To save the settings, press the button .
Table for Setting Up Water Hardness
Position of the
indicator Level Water hardness
1 1 1–7 dH
2 2 8–15 dH
3 3 16–23 dH
4 4 24–30 dH
Preparation of Espresso,Americano, “Coffee”
1. Place acup, mug or glass under the brewing head. Adjust the height
of the brewing head by moving it up or down depending on the size
of your cup, mug or glass. If the cup or glass is too tall, you may
remove the drip tray. After removing the cup or glass, return the drip
tray to its place.
2. Press the Espresso, Americano or Coffee button. The indicator light
of the selected button lights up.
3. The coffee machine will automatically start the grinding, dosing,
tamping and dispensing process.
4. Once the coffee dispensing process is complete, an audible alert
sounds.
Preparing Americano coffee consists of preparing 1 cup of espresso and
adding hot water. Do not remove the cup from under the brewing head
until the hot water dispensing is finished.
You can cancel the preparation of coffee by pressing the corresponding
button.
Preparing Latte/Cappuccino
1. Pour the milk into the milk container and place the container in the
coffee machine.
Note:
To achieve rich and creamy froth, we recommend
using properly chilled milk (around 5°C) with
aminimum fat content of 3%.
2. Place acup, mug or glass under the brewing head. Adjust the height
of the brewing head by moving it up or down depending on the size
of your cup, mug or glass. If the cup or glass is too tall, you may
remove the drip tray. After removing the cup or glass, return the drip
tray to its place.
3. Turn the steam nozzle so that it points into the cup.
4. Press the Cappuccino or Latte button. The indicator light of the
selected button lights up.
5. The coffee machine will automatically start the preparation process
for latte or cappuccino.
6. Once the coffee dispensing process is complete, an audible alert
sounds.
You can cancel the preparation of coffee by pressing the corresponding
button.
Dispensing Hot Water
1. Place acup, mug or glass under the brewing head. Adjust the height
of the brewing head by moving it up or down depending on the size
of your cup, mug or glass. If the cup or glass is too tall, you may
remove the drip tray. After removing the cup or glass, return the drip
tray to its place.
2. Press the Hot Water button. The light of the selected button lights up
and the coffee machine starts dispensing hot water.
3. Once the hot water dispensing process is complete, an audible alert
sounds.
You can cancel hot water dispensing by pressing the button Hot Water.

- 6 - 06/2023
2023, .
Preset Coffee Quantity Table
Coffee Water/coffee volume (ml) Milk volume (ml)
Small Medium Large Small Medium Large
Espresso
coffee
25 45 60 - - -
Coffee 80 120 180 - - -
Americano 30 ml
coffee +
90 ml
water
45 ml
coffee +
135 ml
water
60 ml
coffee +
180 ml
water
Latte 30 45 60 approx
90
approx
155
approx
220
Cappuccino 30 45 60 approx
70
approx
115
approx
180
Hot water 120 180 240 - - -
Brewing Coffee from Ground Coffee
The coffee maker allows the preparation of coffee from pre-ground coffee.
The recommended amount of ground coffee in the preparation of one cup
is 5 to 12 g.
1. Remove the hopper cover and pour the desired amount of coffee into
the machine.
2. Long press the button until the light next to the icon (ground
coffee brewing function) lights up.
3. Press any coffee button and the machine will start.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
USER SETTINGS
User Settings for the Entire Coffee Machine
The settings below (amount of ground coffee, volume of coffee dispensed,
volume of frothed milk and coffee/hot water temperature) will affect the
preparation of all beverages. This is auniversal setting for the entire coffee
machine.
1. Setting the Amount ofGround Coffee
Use the ground coffee quantity adjustment if the prepared coffee is too
strong or weak.
To adjust the ground coffee amount setting, press the button.
Press the button repeatedly to adjust the amount of ground coffee. The
corresponding number of indicator lights will illuminate: 1 light = weak
coffee; 2 lights = medium coffee; 3 lights = strong coffee.
2. Setting the Volume of Coffee Dispensed
The coffee machine allows you to adjust the volume of dispensed coffee.
To adjust the volume of coffee dispensed, use the button. Press
the button repeatedly to adjust the volume of coffee dispensed. The
corresponding number of indicator lights will illuminate: 1 light = small
amount of coffee; 2 lights = medium amount of coffee; 3 lights = large
amount of coffee.
3. Setting the Volume of Frothed Milk
The coffee machine allows you to adjust the volume of frothed milk
dispensed.
To adjust the volume of frothed milk dispensed, use the button. Press
the button repeatedly to adjust the volume of frothed milk dispensed. The
corresponding number of indicator lights will illuminate: 1 light = small
amount of frothed milk; 2 lights = medium amount of frothed milk; 3 lights
= large amount of frothed milk.
4. Coffee/Hot Water Temperature Setting
The coffee maker allows you to adjust the temperature of the coffee/hot
water dispensed.
Use the button to adjust the temperature. Press the button repeatedly
to adjust the temperature of the coffee/hot water dispensed. The
corresponding number of indicator lights will illuminate: 1 light = low
temperature; 2 lights = medium temperature; 3 lights = high temperature.
User Settings for Individual Beverage
The coffee machine allows you to adjust the settings of the beverage you
are about to prepare. However, this will not affect the setting of the entire
coffee machine, only the selected beverage.
1. Long press the button of the selected beverage until the beep
sounds.
2. The controls of the buttons that allow individual adjustment of the
beverage will flash (e.g. for espresso coffee, the button control
will flash; for cappuccino or latte, the and button controls will
flash).
3. Briefly press the button for the selected beverage.
4. The coffee preparation starts.
5. Once the desired amount of coffee has been dispensed into the cup,
press the . The settings are saved in memory.
6. When making acappuccino or latte, the milk frothing is then started.
Once the desired amount of milk has flowed into the cup, press the
button. The settings are saved in memory.
Note:
If you need to cancel the setting (before starting
the coffee preparation), long press the button of the
selected beverage.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ADDITIONAL FUNCTIONS
Automatic Shut-off of the Coffee Machine
Set the idle time, after which the machine will switch off. Automatic shut-
off is used to save electricity.
1. Long press the button and then press the button repeatedly to
set the automatic shut-off time.
2. Each time you press the button, the indicator lights come on:
1 indicator light = automatic shut-off after being idle for 15 minutes;
2 indicator lights = automatic shut-off after being idle for 45 minutes;
3 indicator lights = automatic shut-off after being idle for 90 minutes.
3. Long press the button to confirm, save to memory and go back.
Setting the Power Saving Mode
The appliance can be set to energy-saving mode, in which greater energy
savings are achieved.
1. Long press the button.
2. Press the Americano button repeatedly to switch the power saving
mode setting on/off. If the Americano button light is on, the power
saving mode is on; if the light is off, the power saving mode is off.
3. To confirm, save to memory and go back, long press the button.
Restoring Factory Defaults
If you need to restore the factory settings and erase all your customized
settings, perform afactory reset.
Long press the button and then long press the Coffee. An audible
warning sounds and the machine switches off.
Emptying the Internal Circuit
Use the internal circuit emptying function when the coffee machine will
not be used for along period of time to prevent the water in the circuit from
spoiling and the formation of unwanted microorganisms and odours.
1. Place acup under the coffee spout. Direct the steam nozzle into the
cup.
2. Long press the button.
3. Long press the Espresso until the light flashes.
4. Remove the water tank from the machine, the warning light will flash
.
5. Press the Espresso button again to start the internal circuit emptying
function. The water in the steam nozzle circuit and the coffee outlet
is emptied.
6. Once the function is complete, an audible warning sounds and the
machine switches off.
Note:
During the emptying of the internal circuit, the
sound of the pump will be heard. This is anormal
occurrence.

- 7 - 06/2023
2023, .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CLEANING AND MAINTENANCE
Before cleaning, unplug the power cord from the mains socket and allow
the appliance to cool down.
Warning:
Do not use abrasive cleaning agents, solvents, or any
substances to clean any parts of the appliance that
could damage the surface of the appliance. None
of the components of this appliance are dishwasher
safe.
Warning:
To prevent the risk of electric shock, do not submerge
the appliance, plug or power cord in water or any
other liquid.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DAILY CLEANING AND MAINTENANCE
Regular cleaning and maintenance are crucial for the proper functioning
and longevity of the appliance.
Before cleaning, turn off the appliance, unplug it and allow it to cool down.
Drip Tray and Coffee Grounds Container
• Carefully pull the drip tray out of the body of the machine. Remove the
grid and the coffee grounds tray. Carefully place the drip tray over the
sink and remove the cover.
• Pour the contents of the drip tray into the sink.
• Empty the coffee grounds container into the municipalwaste or
compost.
• Wash the drip tray, its cover, the grid and the coffee grounds tray with
clean water and then dry them properly.
Warning:
Be careful not to scald yourself when handling the
tray. It may contain hot water.
• Place the cover on the drip tray, insert the grid into the open space in
the cover and place the coffee grounds container on top of the cover.
• Put the folded drip tray back into the coffee machine.
Drip Tray Full Indicator
The drip tray is equipped with afloat that serves as adrip tray fullness
indicator. When the water level reaches the maximum amount, the float is
ejected through the opening in the grid. In this case, the drip tray must be
emptied to prevent water from spilling out of the tray.
Warning forfull coffee grounds container
If the indicator light comes on while the coffee machine is running , the
coffee grounds container is full and needs to be emptied.
Water Tank
Remove the water tank, rinse it with clean water and asmall amount of
neutral kitchen detergent. Then rinse it properly with clean water, dry it
and put it back in place.
Coffee Spout
Wipe the coffee spout with asoft, slightly dampened sponge and then
wipe with adry cloth.
Milk Container
To prevent milk build-up and unwanted odours, it is important to clean
them after each use.
1. Place abowl under the brewing head.
2. Fill the milk container with clean water.
3. Direct the steam nozzle into the bowl.
4. Press the Frother Clean button. The coffee maker starts pumping
water from the milk container, which it heats up, and then starts
dispensing hot water and steam through the steam nozzle. This
cleans it and removes the milk residue.
5. Remove the milk container from the machine.
6. Remove the lid of the milk container (Figure E1).
7. Turn the steam outlet upwards (Figure E2) and remove it (Figure E3).
8. Remove the rubber coupling (Figure E4).
9. Pull out the end of the steam nozzle (Figure E5).
10. Release the lock at the bottom of the container and remove the
container from the entire holder (Figure E6).
11. Unscrew the end of the steam nozzle (Figure E7).
12. Wash the all the parts in warm water with asmall amount of
washing-up liquid. Rinse in clean water and wipe dry.
13. Clean the small hole at the end of the steam nozzle with athin object
(e.g. aneedle). It is important that the opening is clean, otherwise the
whole milk frothing system could be damaged.
14. Reassemble the milk container in reverse order and put it back in the
machine.
Outer Surface of the Coffee Machine
To clean the outer surface of the appliance, use aclean, slightly damp
cloth. Afterwards, wipe it dry thoroughly.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CLEANING THE BREWING SYSTEM
To prevent ground coffee from clogging the brewing system and the
internal piping, and to keep the inside of the machine clean, after every
230 cups of brewed coffee, the machine alerts you to clean the brewing
system.
As soon as the button light comes on, the brewing system must be
cleaned. Make sure the drip tray and the coffee grounds container are
empty.
1. Long press the button and the button light will flash.
2. The coffee machine is flushed and water comes out of the spout.
3. When the flush is complete, the icon lights up. Open the cover
and insert the tablet into the hopper. Use espresso machine cleaning
tablets available commercially.
4. Long press the button and the button light will flash.
5. The coffee machine starts cleaning the brewing system. Let it finish
the whole process.
6. When the warning light comes on, remove the drip tray, empty
the coffee grounds tray and clean the drip tray as instructed above.
Place the drip tray back into the coffee machine.
7. It will be possible to use the coffee machine again.
Note:
If you need to start cleaning the brewing system
before the button light comes on, long press the
button and then long press the button.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DESCALING
Mineral deposits from water can accumulate in the internal circuit of the
coffee machine with regular use. It is anatural process. Therefore, regular
descaling is necessary. Mineral deposits can adversely affect the taste of
the coffee being brewed. Therefore, as soon as the button light comes
on, the descaling process must be carried out.
1. Long press the button for and the button light will flash. At the
same time, the warning light will come on to indicate that the
water filter, if fitted, must be removed and the water tank filled with
asolution of water and descaling agent. Use adescaling agent
suitable for espresso-type machines and follow the instructions
given in the descaling agent'saccompanying documentation.
2. After the warning light comes on, remove the drip tray, empty
the coffee grounds container and clean the drip tray as instructed
above. Place the drip tray back into the coffee machine.
3. Now press the button again and the descaling process will start.

- 8 - 06/2023
2023, .
4. If the warning light comes on during the descaling process,
empty the drip tray and the coffee grounds container.
5. When the warning light comes on, remove the water tank, empty
it and refill it with clean water. Insert the tank back into the coffee
machine.
6. Press the button again to flush the internal circuit and remove
any remaining descaler and dirt.
7. After rinsing, the warning light comes on, empty the drip tray and
the coffee grounds reservoir.
8. The descaling process is now complete and the machine can be
used again.
Note:
If you need to start the descaling process before the
button light comes on, long press the button
and then long press the button.
Storage
• If the appliance will not be used for an extended period, unplug it
from the power socket, let it cool down, and clean it following the
instructions provided above.
• Before storing, ensure that the appliance and all accessories are
thoroughly clean and dry.
• Store the appliance in adry, clean, and well-ventilated place away
from extreme temperatures and out of the reach of children or pets.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TROUBLESHOOTING
Problem Cause Solution
The milk squirts out
of the container as it
foams.
There'snot enough
milk in the container.
Refill the milk.
The milk frothing
system is clogged.
Clean the milk
container.
The milk container is
not inserted correctly
in the coffee
machine.
Remove the container
and reinsert it into the
coffee machine.
The amount of frothed
milk is very little or
none.
The internal circuit is
clogged with scale.
Perform the descaling
process.
The coffee grounds
container cannot be
removed together
with the drip tray; or
it is not possible to
insert the drip tray with
the coffee grounds
container into the
coffee machine.
The brewing unit
inside the coffee
machine and the
coffee grounds
container touch and
block each other.
Remove the coffee
grounds container by
hand and then insert
the separate drip tray.
Switch on the coffee
machine and wait for
it to warm up. Remove
the drip tray and place
the coffee grounds tray
on top. Insert back into
the coffee machine.
The coffee doesn't
flow or just drips.
The ground coffee is
too fine.
Adjust the milling
fineness.
The brewing system
is clogged.
Have the brewing
system cleaned.
Coffee spout is
clogged.
Clean the coffee spout.
The internal circuit is
clogged with scale.
Perform the descaling
process.
All warning lights are
flashing.
Coffee machine
malfunction
Turn off the coffee
machine and
disconnect it from the
mains socket. Wait
for awhile before
switching it on again.
If the problem persists,
contact your authorised
service centre.
Note:
If the problem is not listed in the table or if the problem
persists, turn off the coffee machine, disconnect it from the
power source, and contact an authorised service centre.
Warning
indicator Meaning Solution
Empty water tank indicator
light
Refill the water tank.
Full coffee grounds container
indicator
Empty the coffee grounds
container.
Empty bean hopper indicator Add coffee beans to the
hopper.
Milk container incorrectly
installed indicator light
Remove the milk
container and reinsert it.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TECHNICAL SPECIFICATIONS
Rated voltage range..............................................................................220−240 V~
Rated frequency......................................................................................... 50−60 Hz
Rated power input............................................................................................ 1400 W
Noise level......................................................................................................<65 dB(A)
The declared noise emission level of the appliance is <65 dB(A), which
represents alevelAof acoustic power with respect to areference acoustic
power of 1 pW.
We reserve the right to change the text and technical specifications.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTRUCTIONS AND INFORMATION ON DISPOSALOF USED
PACKAGING MATERIAL
Dispose of the packaging material at the designated waste disposal area
determined by your local municipality.
DISPOSAL OFUSED ELECTRICAL AND ELECTRONIC EQUIPMENT
This symbol on the products or accompanying documents
indicates that used electrical and electronic products
should not be disposed of with regular municipal waste.
For proper disposal, recovery and recycling, take these
products to designated collection points. Alternatively, in
some European Union states or other European countries,
you can return your products to the local retailer when
purchasing an equivalent new product. By correctly
disposing of this product, you help conserve valuable natural resources
and contribute to the prevention of potential negative impacts on the
environment and human health that could result from improper waste
disposal. For more details, contact your local authority or nearest
collection facility. Failure to properly dispose of this type of waste may
result in fines in accordance with national regulations.
For Businesses in European Union Countries
To dispose of electrical and electronic equipment, obtain the necessary
information from your retailer or supplier.
Disposal in Countries outside the European Union
This symbol is valid within the European Union. To dispose of this product,
obtain the necessary information on the correct disposal method from
local authorities or your retailer.
This product complies with all the essential requirements of
the EU directives that apply to it.

FAST ČR, a.s.
U Sanitasu 1621
CZ-251 01 Říčany
www.sencor.eu