Sencor SSS 3400K User manual
SSS 3400K
EN User Manual Wireless karaoke speaker
CZ Uživatelská příručka Bezdrátový karaoke reproduktor
SK Používateľská príručka Bezdrôtový karaoke reproduktor
HU Felhasználói kézikönyv Vezeték nélküli karaoke hangszóró
PL Podręcznik użytkownika Bezprzewodowy głośnik karaoke
EN – 2
SAFETY INSTRUCTIONS
This product has been designed with the utmost safety in mind.
However, incorrect use may lead to electric shock or re. This is
why users should observe the following instructions when using this
device.
This device uses a semiconductor unit and contains no user
serviceable parts. Do not disassemble this device, otherwise you
are exposed to the risk of electric shock. If any damage to this
product occurs, please have this product repaired by a qualied
service technician.
Power
Power supply of this unit must be match the serial plate data.
Heat source
Keep this unit out of heat sources like stove or direct sunlight.
Cleaning
Prior to cleaning, please disconnect power rst. For cleaning, don’t
use liquid detergents or caustic liquids - just clean the unit with
a soft cloth.
Heavy objects
Do not place heavy objects on the unit, otherwise damage might
occur.
Wireless karaoke speaker
EN – 3
Wireless karaoke speaker
Connecting other devices
Before connecting other devices to this unit, please make sure to
disconnect power. Otherwise damage to the unit or personal injury
might occur.
Faults to be repaired
If any of the following problems occurs, please disconnect power to
the unit and contact a qualied service technician.
A. Power cord or plug is damaged.
B. Liquids or other foreign objects have penetrated inside the
product.
C. If the unit does not work even if it’s being operated according
to the instructions, don’t press any buttons other than those
described in these instructions. Otherwise, damage to this unit
may occur along with a more demanding repair.
D. This unit has fallen on the ground from a big height.
E. Burns can be smelled from the product inside.
Maintenance
If you don’t have enough technical knowledge necessary to maintain
this unit, don’t attempt to repair it by yourself. By removing the
cover, you are exposed to a risk of electric shock. If needed, please
contact a qualied service technician.
Replacement of parts
If you need to replace any part of this unit, ask your service
technician to make a replacement for equal spare part models. If
other spare part models are used for replacement, serious damage,
electric shock or shortening the unit’s lifetime may occur.
EN – 4
Safety check
After completing maintenance, ask your service technician to
perform an on-site safety check to ensure that the unit is operating
safely.
Remark:
Before using this product, read these instructions carefully and keep
it well for future use.
EN – 5
SUPPLY CONTENT
1x BT speaker SSS 3400K
2x Wireless microphone
2x Microphone holder
1x AUX-IN cable (3.5mm)
1x USB-C charging cable
1x User’s manual
DESCRIPTION OF THE BT SPEAKER
AND MICROPHONE
EN – 6
EN – 7
SSS 3400K front side
A Wireless microphone 1
B Wireless microphone 2
C Removable holder for wireless microphone 1
D Removable holder for wireless microphone 2
E BT speaker carrying handle
F LED eect
G Treble speaker
I Wideband speaker
SSS 3400K top side
1On/o button
2Light eects button (change/on/o)
3 Previous track button, microphone volume down
4PLAY / PAUSE / Change Source button (Bluetooth, memory
card, USB, AUX-IN, COAX)
5 Next track button, microphone volume up
6 “ECHO -” level down button
7 “ECHO +” level up button
8 Rotary volume down/up control
9 Projections for mounting the microphone holder
EN – 8
10 TONE button to change the predened voice eect
11 LED indicator
SSS 3400K back side
12 COAX input
13 Input for audio AUX IN mini jack (3.5mm)
14 Memory card slot
15 USB-A for playback from memory device
16 Charging socket (USB-C)
17 LED charging indicator
Wireless microphone
18 Sound sensor
19 LED indicator
20 On/o button
21 Charging socket (USB-C)
EN – 9
PUTTING INTO OPERATION
Before rst use, be sure to read the safety instructions contained in
this user's manual carefully.
Before rst use, please charge the BT speaker to a maximum level.
Hold down the power on button to turn on the BT speaker. Turning
on/o is indicated by a sound signal. To turn the BT speaker o,
hold down the power on button. To change the source of the music
being played, press and hold the “Play / Pause / Change Source”
button while it is on.
TRANSMISSION AND BT SPEAKER POSITION
To carry the BT speaker, use the “E” handle located on the top of
the BT speaker. The speaker oers 1 positioning option. The side
designated for the correct position is always tted with rubber feet
on the underside of the BT speaker.
Caution: always position the equipment so that it does not
endanger the health of persons in the vicinity or cause damage to
property.
PAIRING DEVICES VIA BLUETOOTH
Turn on the BT speaker and search for its Bluetooth name
“SSS 3400K” in the device to be paired, then start the pairing
EN – 10
process. If you are requested to enter a pairing code while your
device and the BT speaker are pairing, use the code: “0000”.
To disconnect the paired device, end the pairing session on
your mobile device or long hold the “Change source” button.
Disconnection will be indicated by an acoustic tone.
Remark: To ensure a stable Bluetooth connection, make sure that
the distance between the BT speaker and your connected device is
kept within 10 meters.
AUDIO AUX IN
The BT speaker is equipped with a 3.5mm jack. Your device can
be connected to the BT speaker via the supplied audio cable.
First connect the audio plug to your device and then to the BT
speaker’s jack.
Please note: before connecting your device and BT speaker, make
sure that the output signal from your device is at the minimum level
(minimum output volume). This will prevent the BT speaker from
damage. When the audio cable is connected, the BT speaker does
not meet the water ingression protection class.
Remark: In this mode, not all functions of the BT speaker are
available. The Bluetooth function is not active if the audio jack is
connected to the BT speaker.
EN – 11
COAX INPUT
Connect the digital input to the output of your device. Switch the
input mode to COAX by pressing and holding the “Play / Pause /
Change Source” button. Set the correct codec on the output device.
A poorly chosen codec on the output device will manifest itself in the
BT speaker as a rattle.
RESET BUTTON
To reset the BT speaker, press and hold the “ECHO + Button” and
“Light Eects Button” simultaneously. Reset will turn o the BT
speaker. Switch on the BT speaker.
RECOMMENDATION: If there is an unexpected problem with the
BT speaker connection or its functions. Reset the BT speaker.
PLAY / PAUSE / CHANGE SOURCE BUTTON
Press the “Play / Pause / Change Source” button briey to start
or pause music playback during a Bluetooth connection when
a memory card or USB storage media is inserted.
Long press the “Play / Pause / Change Source” button to change
the source from the input or media being played.
EN – 12
VOLUME CONTROL
The BT speaker volume (+/-) is controlled using the rotary control
on the BT speaker. Turn the rotary control to the left to reduce the
volume. Turn the rotary control to the right to increase the volume.
The volume setting does not apply to microphone volume settings.
For more information on setting the microphone volume, see
Wireless microphones.
Warning: Before starting to play music, make sure the volume
control is not turned up to the maximum level.
LIGHT EFFECTS
The BT speaker is equipped with lighting eects at the top of the
device. Changing the light eect is done by pressing the “light eects”
button, 6 light eects are preset. To turn o the light eects, long hold
the “light eects” button. To switch on the light eects, long press the
“light eects” button.
PLAYBACK FROM USB STORAGE MEDIA /
MEMORY CARD
USB-A playback
Insert the USB storage disc with audio content in the USB slot. Long
press the “Play / Pause / Change Source” button to switch to USB
EN – 13
playback mode. The music playback from the connected storage
will start automatically. Upload your music to the storage in the order
in which it will be played by the BT speaker. Supported playback
formats are listed in the technical specication.
Memory card playback
Insert the memory card with the contacts facing the USB-A port.
When you insert a memory card, the BT speaker will automatically
start playing back its contents. If there is no le to play on the
memory card, the BT speaker will switch to the last active source
being played. To release the TF memory card, press it gently
into the BT speaker with your ngernail or a blunt instrument and
the card will release. Then you can carefully remove it with your
ngernails (or with tweezers). Supported playback formats are listed
in the technical specication.
Warning: Due to a number of devices on the market, compatibility
and playback support are not guaranteed for all media. The memory
devices you want to connect should be tested in advance and/
or formatted as FAT32. The playback of protected media, les or
content stored inside them may fail.
WIRELESS MICROPHONES
2 wireless microphones are included in the package. Attach the
microphone holders “C” and “D” to the BT speaker projections by
sliding them on.
EN – 14
Before rst use, charge both microphones using the USB-C
charging cable. The charging process will be indicated by a red
LED.
Microphone control:
is done with the “on/o” button on the microphone.
Turning the
microphone on
and o.
To switch on, press and hold the “on/o”
button on the microphone.
Change the
volume of the
microphones.
To lower the volume, hold down the previous
track button on the BT speaker.
To increase the volume, hold down the next
track button on the BT speaker.
Change the ECHO
mode.
To lower the volume, press the previous
track button on the BT speaker.
To increase the volume, press the next track
button on the BT speaker.
Change the eects
of the voice.
Press the TONE button “10” repeatedly to
change the voice eect on the BT speaker.
LED indicator:
Red uninterrupted led – microphone is charging / microphone is
discharged
No indication – microphone o/charged
Green intermittent indication – microphone connecting to BT
speaker
EN – 15
Green uninterrupted indication – successful connection of
microphone to BT speaker
Warning: Avoid feedback by keeping the microphone far enough
away from the SSS 3400K speakers.
If you get too close, feedback will occur and may result in damage
to the speakers or the hearing of a person near the system.
CHARGING THE BT SPEAKER
A charged battery provides power for several hours of operation at
normal volume levels. A high volume consumes more battery power;
therefore, we recommend listening at normal volume levels. To
charge the BT speaker, please connect the charging adapter to the
mains and then to the BT speaker. Use your own 5V, 2A charging
adapter. The charging indicator on the back will glow red until the
battery is fully charged. A low battery level will be indicated by an
audible alert and a blue intermittent LED indicator on the top of the
BT speaker.
Warning: For charging, use only the original accessories supplied
with the appliance. To achieve the maximum battery lifetime, it is
best not to start charging until the low battery audible alert is output.
Charge continuously until fully charged. When the battery operating
time becomes very short, the battery lifetime has been used up; we
recommend that you have the battery replaced at your authorized
centre.
EN – 16
Recommendation: If the unit is not to be used for an extended
period of time, we recommend to fully charge the battery once every
two to three months. We recommend to store the unit with a the
battery charged to prevent irreparable damage to the battery (loss
of capacity).
TECHNICAL SPECIFICATIONS
SSS 3400K
Wireless karaoke speaker
Features:
Two wireless microphones in the package
Light eects with the option to switch o
Maximum speaker output 30W
Sound:
Maximum speaker output 30W
1 full-range + 1 wideband speaker and 1 tweeter
Frequency response: 30Hz–20kHz
Total harmonic distortion: ≤ 5%
Wireless microphones
Bluetooth connection V5.2
Range up to 10m
Transmission frequency 60Hz–13kHz
Rechargeable microphone battery: 1,200mAh Li-Ion each
Up to 40 hours of operation on a full charge
ECHO function
EN – 17
Inputs:
Bluetooth Audio 5.0
AUX audio input (3.5mm stereo connector)
Playback from USB (up to 32GB / MP3)
Card Slot (up to 32GB / MP3)
Coaxial input
Other:
Rechargeable speaker battery: 4,000mAh Li-Ion
Playback time of up to 9 hours (@ 50% volume)
USB-C power
Accessories: USB charging cable, 3.5mm external cable (AUX),
user’s manual
Dimensions: 280×273×168mm
Weight: 2,000g
Bluetooth
microphone
Version 5.2
Maximum Transmitter
Power
100mW @ 2.4GHz–
2.4835GHz
Bluetooth
SSS3400K
Version 5.0
Maximum Transmitter
Power
100mW @ 2.4GHz–
2.4835GHz
Codec SBC
Proles A2DP / AVRCP
EN – 18
INSTRUCTIONS AND INFORMATION ON THE DISPOSAL OF DISCARDED
PACKAGING MATERIALS
Take the packaging material to a collection yard for disposal.
DISPOSAL OF DISCARDED ELECTRICAL AND ELECTRONIC EQUIPMENT
This symbol on the product, accessory or packaging indicates that
the product must not be treated as normal household waste. Please
dispose of this product in a collection yard designated for the recycling
of electrical and electronic equipment. In some EU countries or in
some European countries, you can return your products to your local
retailer when you buy an equivalent new product. Correct disposal
of this product helps save valuable natural resources and prevents
possible adverse impacts on the environment and human health that
might be caused by improper waste disposal. Please contact your
local authority or the nearest waste collection yard for further details.
Improper disposal of this type of waste may be subject to a legal ne.
For companies in the European Union
If you need to dispose of electrical or electronic equipment, ask your
dealer or supplier for the necessary information.
Disposal in countries outside the European Union
To dispose of this product, please ask your local authorities or dealer
for the necessary information on correct disposal.
This product complies with EU requirements.
FAST ČR, a.s. hereby declares that the radio device type SSS 3400K conforms
to the 2014/53/EU directive. The full text of the EU Declaration of Conformity is
available at: www.sencor.eu.
EN – 19
Changes in the text, design and technical specications may be made without
prior notice and we reserve the right to make such changes.
The original version is in Czech.
Manufacturer’s address:
FAST ČR, a. s., U Sanitasu 1621, Říčany CZ-251 01
EN – 20
EN Warranty conditions
Warranty card is not apart of the device packaging.
This product is warranted for the period of 24 months from the date of purchase to the end-user. Warranty
is limited to the following conditions. Warranty is referred only to the customer goods using for common
domestic use. The claim for service can be applied either at dealer’sshop where the product was bought, or
at below mentioned authorized service shops. The end-user is obligated to set up aclaim immediately when
the defects appeared but only till the end of warranty period. The end user is obligated to cooperate to certify
the claiming defects. Only completed and clean (according to hygienic standards) product will be accepted.
In case of eligible warranty claim the warranty period will be prolonged by the period from the date of claim
application till the date of taking over the product by end-user, or the date the end-user is obligated to take it
over. To obtain the service under this warranty, end-user is obligated to certify his claim with duly completed
following documents: receipt, certificate of warranty, certificate of installation.
This warranty is void especially if apply as follows:
Defects which were put on sale.
Wear-out or damage caused by common use.
The product was damaged by unprofessional or wrong installation, used in contrary to the applicable
instruction manual, used in contrary to legal enactment and common process of use or used for another
purpose which has been designed for.
The product was damaged by uncared-for or insufficient maintenance.
The product was damaged by dirt, accident of force majeure (natural disaster, fire, and flood).
Defects on functionality caused by low duality of signal, electromagnetic field interference etc.
The product was mechanically damaged (e.g. broken button, fall).
Damage caused by use of unsuitable media, fillings, expendable supplies (batteries) or by unsuitable
working conditions (e.g. high temperatures, high humidity, quakes).
Repair, modification or other failure action to the product by unauthorized person.
End-user did not prove enough his right to claim (time and place of purchase).
Data on presented documents differs from data on products.
Cases when the claiming product cannot be indentified according to the presented documents (e.g. the
serial number or the warranty seal has been damaged).
Manufacturer:
FAST ČR, a.s., U Sanitasu 1621, Říčany 251 01, Czech Republic
Visit www.sencor.com for detailed information about authorized service centers.
The original version of the instructions is in the Czech language, other language versions are made by the
appropriate translation.
Table of contents
Languages:
