Sensata Magnum Energy ME-RC User manual

LED Indicators
On/Off Push Buttons
Menu Buttons
Rotary Select Knob
LCD Display
Lithium Battery Settings
QUICK REFERENCE GUIDE
STANDARD LFP SETTINGS AVAILABLE FOR THE FOLLOWING MAGNUM ENERGY INVERTER/CHARGER MODELS
Using the Magnum Energy ME-RC or ME-MR Remote Controls, set Magnum Energy
inverter/chargers to charge lithium iron phosphate (LFP) batteries.
• MS2000
• MS2012
• MS2812
• MS2024
• MS4024
• MS4048
• MSH3012M
• MSH3012RV
Access LFP battery settings
via built-in RV control panels
using the ME-RVC bridge.
ME-RC Remote Control
From the ME-RC Remote Control version 2.9 or higher,
program your Magnum Energy inverter/charger to
charge lithium batteries.
STEP TWO: Set the Absorb Time setting
to battery manufacturer’s specifications.
The setting is determined by the 20-hour
amp-hour capacity of your battery bank.
Press Setup
Rotate to Absorb Time
Press Rotary Knob
to select
Rotate to 1 hour
Press Rotary Knob to save
Status...
03 Absorb Time
Status...
Absorb Hrs = 1.0
STEP THREE: Set the Battery Type
setting to LFP.
Status...
04 Battery Type
Status...
BatType = LFP
Press Setup
Rotate to Battery Type
Press Rotary Knob
to select
Rotate to LFP
Press Rotary Knob to save
• MSH4024M
• MMS1012
• MMSA1012
STEP ONE: Set the Low Battery Cutout to
battery manufacturer’s specifications.
Press Setup
Rotate to Low
Battery Cutout
Press Rotary Knob
to select
Rotate to battery
manufacturer’s specs, or
11.0 VDC if not specified.
Press Rotary Knob to save
Status...
02 LowBattCutOut
Status...
LowBattCutOut = 11.0

www.sensata.com
CONTACT US
651-653-7000
800-553-6418
[e-mail]
Power Conversion
www.Magnum-Dimensions.com April 2020 PN 64-5029 Rev A
From the ME-MR Remote Control version 1.3 or higher,
program your Magnum Energy inverter/charger to
charge lithium batteries.
Press Menu/Home
button until the display
shows BAT AHRS
The current “saved”
setting is indicated by
an arrow in the bottom
right-hand corner of
the display
Press On/Off/Change
button until 200 AH
is shown
STEP TWO: Set the Battery Type
setting to LFP.
LED Indicators
On/Off/Change Button
Menu/Home Button
Save/Hold Button
LCD Display
ME-MR Remote Control
BAT AHRS
400 AH
BAT AHRS
200 AH
Press Save/Hold
button to save the
200 AH setting
BAT AHRS
200 AH
STEP ONE: Set the Battery Amp Hours
to 200 AH = 1 hour.
Press Menu/Home
button until the display
shows BAT TYPE
The current “saved”
setting is indicated by
an arrow in the bottom
right-hand corner of
the display
Press On/Off/Change
button until LFP
is shown
BAT TYPE
FLOODED
BAT TYPE
LFP
Press Save/Hold
button to save the
LFP setting
BAT TYPE
LFP
BAT AHRS
400 AH
BAT TYPE
FLOODED
Guide provided for reference only. Please read the
full Owner’s Manual for each remote control.
STEP THREE: Set the Low Battery Cutout
to battery manufacturer’s specifications.
Press Menu/Home
button until the display
shows LBCO
The current “saved”
setting is indicated by
an arrow in the bottom
right-hand corner of
the display
Press On/Off/Change
button until correct
Low Battery VDC
setting is shown for
your battery specs, or
11.0VDC if not specified.
LBCO
10.0VDC
LBCO
11.0VDC
Press Save/Hold
button to save the
LBCO setting
LBCO
11.0VDC
LBCO
10.0VDC