Sensica sensilight mini User manual

1
CONTRASTE chromo mat 100gr (by Condat)
User Guide
Instrucciones De Uso
Mode D’emploi
Mini

1
Table of contents
What is sensiLight™ Mini 2
sensiLight™ Mini device description 3
Who should use sensiLight™ Mini 6
When shouldn’t sensiLight™ Mini be used 6
Possible side eects 9
Benets 10
User instructions 11
Preliminary test 12
Recommended treatment protocol 13
Post-treatment care 18
Cleaning and troubleshooting 18
Customer service 19
Device specication parameters 20
Treatment log 21
Labeling 25
© All rights reserved to Home Well Trading Ltd.
English

2
What is sensiLight™ Mini
sensiLight™ Mini is a personal use device
intended for the removal of unwanted hair.
sensiLight™ Mini features Sensica®
proprietary RPL™ technology (Reactive
Pulsed Light).
RPL™ (Reactive Pulsed Light)
how does it work?
sensiLight™ Mini is based on the scientific
principle of selective photothermolysis.
sensiLight™ Mini RPL™ (Reactive Pulsed
Light) advanced technology uses clinically
proven IPL technology along with a
combination of unique skin condition
sensors. The light penetrates the epidermis
to the dermis and is absorbed by the
melanin in the hair shaft. The heat is
generated by the absorbed light then
dissipates into the follicle and generates
local thermal damage, causing a reduction
in hair growth.
Long-term hair reduction – hair
growth cycle
Two factors play an important role in
optimal long-term hair reduction:
• Hair growth cycle involves three phases:
Anagen, Catagen, and Telogen. Anagen
is the growth phase, while Catagen and
Telogen are the resting phases. Permanent
hair reduction can only occur during the
Anagen phase.
• Skin types (according to the Fitzpatrick
scale) are illustrated in the diagram at
the back cover. Darker skin contains
more melanin, which competes with the
targeted hair for light energy absorption.
When more light energy is absorbed
into the skin, there is a greater risk for
adverse effects and the epidermis may be
damaged.
PLEASE MAKE SURE TO CAREFULLY
READ THIS USER GUIDE BEFORE YOU
START TREATING WITH sensiLight™
Mini. THE USER GUIDE, AS WELL AS
AN INSTRUCTIONAL VIDEO, CAN ALSO
BE FOUND AT WWW.SENSICA.COM
English

3
sensiLight™ Mini device
description
sensiLight™ Mini kit includes the following
main components:
• sensiLight™ Mini handheld device
• External power supply
Handheld description
English

4
User interface description
The user interface and control
capabilities include the following
features:
1. ON/OFF and energy selection button.
• Single button used for the device
activation, deactivation, and energy
selection.
• Pressing the button (after the device is
connected to the power supply) will turn
the device on at energy level 1. Each press
will change the energy, from the lower
level to the higher, for a total of 3 different
energy levels.
• The device will switch to standby mode
when left unattended or by pressing the
ON/OFF button for 3 seconds.
2. Trigger button (flash pulse activation)
marked as s “sun”on the upper side of the
device. The trigger button will activate the
flash lamp if the treatment window is in full
contact with the skin, and the skin tone is in
within the allowed range. Pressing the button
once will activate a single pulse, pressing
and holding the button will activate pulses
English

5
Indicator Mode
No light OFF Device not working (not connected to the power supply).
“Blinking”
green light
Standby Device is in standby mode (before powering on or when
left unattended for 3 minutes).
1-3 energy level
lights
green light
Energy
level 1-3 The three energy levels are indicated by three green LED lights.
“Steady”
green light
ON Pulse is ready.
“Momentary”
orange light
Activation
(pulse) blocked The device does not deliver a pulse due to the lack of full skin contact.
“Momentary”
red light
Activation
(pulse) blocked The device does not deliver a pulse due to non-allowed skin tone (high Fitzpatrick level as described at the
beginning in the Long-term hair reduction-Hair growth
cycle section).
“Blinking”
orange light
Close to end
of life Indicates about the close end of lamp life time.
“Steady”
red light
End of life/
blocked Device is permanently blocked, the lamp has reached the end of its life time or internal malfunction has been
occurred.
English

6
continuously as long as the button is pressed .
Who should use sensiLight™
Mini
• sensiLight™ Mini is intended for women and
men who desire to remove unwanted hair.
• sensiLight™ Mini
is intended for use on
legs, arms, underarms, bikini line, back,
shoulders, chest, and allowed facial areas.
• sensiLight™ Mini is intended for use on skin
tone types 1 to 5 according to Fitzpatrick
skin chart below (see also colored chart at
the back cover of this User Guide).
12345 6
The use of sensiLight™ Mini on naturally dark
skin is forbidden.
• sensiLight™ Mini works best on dark
hair or hair that contains more melanin.
Brown and light brown hair will respond,
but typically will require more treatment
sessions. Red hair may show some
response. Naturally white, grey or blond
hair shows more limited response.
Nevertheless, some users have noted
hair reduction after multiple treatment
sessions.
When shouldn’t sensiLight™
Mini be used
Who cannot use sensiLight™ Mini-
CONTRAINDICATIONS
• Do not use sensiLight™ Mini if you
are under the age of 18. The use of
sensiLight™ Mini on or by children has
not been established and could result in
serious injury.
• Do not use sensiLight™ Mini if you are
pregnant or with a slight chance of being
pregnant or nursing since it has not been
established and may result in stimulation
of pigmentation.
• Do not use the device if you have skin
cancer or on areas at risk of malignancy or
if you have received radiation therapy or
chemotherapy within the past 3 months,
since it has not been established and the
immune system can be compromised
which can lead to serious injury.
• Do not use sensiLight™ Mini if you suffer
from epilepsy, it could trigger a seizure.
• Do not use on damaged or broken skin or
if you have a history of herpes or psoriasis
English

7
outbreak in the treatment area since it can
result in serious side effects.
• Do not use if you suffer from keloid scar
(growth of extra scar tissue where the skin
has healed after an injury) formation since
it has not been established and may result
in serious skin complications.
• Do not use if you have been taking
Tetracycline antibiotics and/or medication
with the following active ingredients
within the last two weeks: Retinoid acid,
Retina-A, Vitamin A such as Accutane as it
is considered to be a photo-sensitive drug
and may result in serious skin injury.
• Do not use sensiLight™ Mini if you are
photosensitive or have other diseases
related to light sensitivity as it may lead to
serious injury.
• Do not use if you suffer from severe or
decompensated metabolic conditions,
such as diabetes since it may cause
a greater risk of delayed healing and
infection in the case of an adverse effect.
• Do not use if you have had a skin peel
or other skin resurfacing procedure
within the last 8 weeks as it may result in
stimulation of pigmentation.
• Do not use sensiLight™ Mini on the face
areas above the cheek line or around eyes,
eyebrows and eyelashes as this could
cause serious eye damage.
Note:
If you have undergone any other aesthetic
procedures or have any uncertainty
regarding potential side effects, consult your
physician before using sensiLight™ Mini
What you must do to avoid serious
harm - WARNINGS:
• Do not open or repair the device as it
may expose you to dangerous electrical
components which may cause serious
bodily damage.
• Do not place, store or use sensiLight™ Mini
near bathtubs, showers, basins or other
vessels containing water as this may cause
severe electrocution.
• Do not leave sensiLight™ Mini unattended
while plugged into the electricity as it may
lead to electrocution risk.
• Never look directly at the light coming
English

8
from the sensiLight™ Mini treatment
window as it may cause eye injury.
• Never use flammable liquids such as
alcohol (including perfumes, sanitizers, or
other applications containing alcohol) or
acetone to clean the skin one hour before
using sensiLight™ Mini as it may cause
burning of the skin.
• Do not use sensiLight™ Mini if you have an
active implant such as pacemaker, insulin
pump or similar devices since it may cause
interference.
• Do not use sensiLight™ Mini on tanned
skin or after sun exposure as this can
cause serious burns or skin injury. Avoid
exposure to the sun for 4 weeks prior each
treatment.
• Do not use sensiLight™ Mini on naturally
dark skin (see guidance at the back cover
and high Fitzpatrick level in the “Who
should use the sensiLight™ Mini “ section).
• Do not use sensiLight™ Mini if you have
dark brown or black spots such as freckles,
birth marks, around the nipples, moles or
blisters on the area to be treated.
• Do not use sensiLight™ Mini on mucous
membranes such as nostrils, lips of the
mouth, eyelids, ears, genital area and the
anus as it may lead to serious injury.
• Do not use sensiLight™ Mini if you have
piercing or any metal items such as
earrings or jewelry on the area to be
treated as it may cause burns.
• Do not use sensiLight™ Mini if you have
tattoos or permanent make up on the area
to be treated.
What you must do to avoid other
harm - CAUTIONS:
• Use sensiLight™ Mini only according to the
instructions for use.
• Hair removal by lasers or intense pulse
light sources can cause increased hair
growth in some individuals. Based upon
currently available data, the highest risk
group for this response is females of
Mediterranean, Middle Eastern, and South
Asian heritage treated on the face and
neck.
English

9
• This appliance is not intended for use by
individuals with reduced physical, sensory
or mental capabilities.
• Do not use the device if:
• The device is not working properly,
appears damaged or broken (UV and IR
emitted from this device).
• The cord or plug is damaged.
• You see or smell smoke.
• The outer shell is damaged or loose.
• Lamp or treatment window is
damaged, or missing.
• Optical skin tone sensor is cracked, or
broken.
• It becomes damp or wet.
• Avoid more than 15 minutes of sun
exposure for at least 2 weeks post
treatment. If during these 2 weeks your
treated skin area is exposed to sunlight,
make sure to apply SPF 30 or higher
sunscreens.
• Do not treat the same area of skin more
than once per treatment as it may cause
skin irritation.
Note:
sensiLight™Mini is designed for use by a
single user.
English

10
Possible side effects
When using sensiLight™ Mini according
to the instructions for use, side effects
are rare. However, every aesthetic
procedure including the usage of home-
use devices may cause some degree of
side effects. Therefore, it is important that
you understand and accept the risks and
complications that can occur with pulsed
light hair removal system:
Degree of
side effects Side effects
Minor
side-effects
Skin irritation
Skin redness
Skin sensitivity
Rare
side-effects
Skin burns
Scarring
Pigment changes
Excessive redness
and swelling
Extremely rare
side-effects
Infection
Bruising
Benefits
sensiLight™ Mini features an automatic
built-in skin color sensor that is designed
to provide you with complete safety and
reassurance. The sensor constantly evaluates
your skin tone and allows sensiLight™ Mini
to perform only on suitable areas. This smart
safety feature also automatically disables
the treatment if your skin is too dark or too
tanned.
As an extra precaution, the applicator tip
has been designed to only emit light pulses
when it is in full contact with your skin.
Response to sensiLight™ Mini hair removal
differs between individuals, depending on
biological factors and how closely treatment
instructions are followed.
Based on the treatment regime in this
User Guide you should expect to see some
improvement in 3-4 weeks.
Hair will continue to grow, up to two weeks
after a hair reduction session. However,
afterwards, as the hair grows in three
English

11
User instructions
sensiLight™ Mini is intended for use on
legs, arms, underarms, bikini line, back,
shoulders, chest, and on allowed facial
areas.
Device set-up
1. Remove all components from the box
(handheld device and power supply).
2. Before beginning the treatment, make
sure the device is clean, dry, and intact.
3. Plug the power supply end into electrical
outlet and the cord end into the device
socket (see image - item 6).
sensiLight™ Mini is now ready for use.
How to prepare yourself
1. Prior to use, make sure your skin is
shaved, clean and dry (free of any
residues of powders, creams, makeup,
antiperspirants, or deodorants).
2. Between treatments, you can shave but
don’t wax or pluck hair.
3. Never use flammable liquids such as
alcohol (including perfumes, sanitizers, or
other applications containing alcohol) or
acetone to clean the skin one hour before
using sensiLight™ Mini as it may cause
burning of the skin.
Remember! sensiLight™ Mini comes with
a built-in skin-tone sensor, enabling the
application only on a suitable skin tone
range. This unique safety feature will not let
you treat areas where your skin is too dark
or too tanned, even if your general skin type
is lighter.
• For sensiLight™ Mini maintenance and
prolonged use, device cleaning is a must
(Cleaning chapter).
• Perform a preliminary test on a small
patch of the skin (preferably on the
intended treatment area) 48 hours
prior to first use of sensiLight™ Mini, to
determine energy level settings for your
treatment (as depicted in the preliminary
test section).
• Do not use sensiLight™ Mini on the
face above the cheek line: around eyes,
eyebrows, or eyelashes as this could
cause serious eye damage.
• sensiLight™ Mini is suitable for men.
However, male body hair, especially on
the chest, will require more hair reduction
sessions.
English

12
Preliminary test
The preliminary test is intended to
determine your skin’s reaction to
sensiLight™ Mini treatment and to help
you set the optimal energy level for each
treatment area.
Perform a preliminary test on each area
you intend to treat 48 hours prior to the full
treatment.
Note:
Do not treat full areas with energy levels
that you have not tested before!
Do not treat the tested area for at least 48
hours after the preliminary test is done.
1. Select the lowest energy level and deliver
a pulse on the selected preliminary test
skin area.
2. If you feel comfortable with the energy
level, increase it to level 2 and perform an
additional pulse on the next spot.
3. Only if you feel comfortable, you may
reach the maximum energy level 3.
4. Stop the test once you do not feel
comfortable, as increasing the energy
level increases the risk of adverse effects.
5. If you see adverse effects such as severe
redness or blistering stop the test
immediately.
6. Wait 48 hours and examine the tested area.
If the skin in the tested area seems normal
(no response or mild redness), you can
proceed with a full treatment in the highest
comfortable energy level that you have
tested. If you see extreme redness, swelling,
or blistering even in the low-energy level
settings, do not do the full treatment in
that area.
How to use sensiLight™ Mini device
Note:
A preliminary test should be conducted
before proceeding to a full treatment. See
“Preliminary test section” above.
1. To turn sensiLight™ Mini on, press the ON/
OFF button (see image - item
1
). Energy
level 1 green indicator will light up.
2. The device sets itself on the lowest energy
level - level 1. For other energy levels
press the energy level selection button (see
image - item
1
).
3. You may decrease or increase the energy
level according to your convenience
(to reach the level determined in the
preliminary test section). The energy level
lights (see image – item
4) will light up
green on the level scale according to the
selected energy level.
English

13
4. Place sensiLight™ Mini treatment window
(see image - item 7) on the desired
body area with full contact to the skin. If
sensiLight™ Mini is not properly applied
or your skin tone is too dark/tanned, the
indicator will be“blinking”red. In this
case, sensiLight™ Mini will not trigger a
pulse in that area of your skin.
5. Press the trigger button (see image - item
2) and hold it pressed for continuous
pulsing.
6. Press the trigger button once for single
pulse.
7. While pressing the trigger button, you will
see a bright flash, you will hear a popping
noise and you may feel a mild stinging
and/or heat sensation.
8. Keep the trigger button pressed and start
moving the device with each pulse to the
next spot without detaching it from the
skin. The device will immediately recharge
and will be ready for the next pulse.
Repeat process until the entire treatment
area has been covered.
9. After the treatment, turn off the device
by pressing the“ON/OFF” button for
3 seconds; a steady orange indicator
will light up, while the device is in the
shutdown mode. Unplug the unit after
each treatment session.
Important notes:
• Try not to overlap pulses on the same
spot. Repeated pulses on the same spot
may cause burns.
• Do not treat the same area of skin more
than once per treatment as it may cause
skin irritation.
• sensiLight™ Mini will not trigger a pulse if:
• There is no full contact of the
treatment window with the body skin.
• Your skin tone is too dark or tanned.
Recommended treatment
protocol
Typical sensiLight™ Mini treatment
interval:
While treating with sensiLight™ Mini, do not
overlap pulses on the same spot of skin.
• Body hair: the first 1–4 hair removal
treatments will be approximately two
weeks apart.
The next 5-8 hair removal treatments will
be four weeks apart.
• Facial hair: the first 1–5 hair removal
treatments will be approximately two
weeks apart.
English

1414
The next 6-8 hair removal treatments will
be four weeks apart.
• Treatment 8+ hair removal treatments
will be as needed, until desired results are
achieved.
Energy levels:
Recommended energy levels are dependent
on both your hair color and skin tone in the
treated area. For your convenience – below
is a table of recommended energy levels per
each option.
Important: Facial treatment should be
performed at 1-2 energy levels only
1 2 3 4 5 6
Black Energy 2-3 Energy 2-3 Energy 2-3 Energy 1-2 Energy 1-2
Dark brown Energy 2-3 Energy 2-3 Energy 2-3 Energy 1-2 Energy 1-2
Brown Energy 2-3 Energy 2-3 Energy 2-3 Energy 1-2 Energy 1-2
Dark blond Energy 2-3 Energy 2-3 Energy 2-3 Energy 1-2 Energy 1-2
Light brown Energy 2-3 Energy 2-3 Energy 2-3 Energy 1-2 Energy 1-2
Red head Energy 2-3 Energy 2-3 Energy 2-3 Energy 1-2 Energy 1-2
Grey/ white Energy 2-3 Energy 2-3 Energy 2-3
Skin type
Hair
English

1515
Plan your sensiLight™ Mini treatment
Energy level should primarily be chosen
based on your own comfort.
The energy levels vary from level 1 to level 3
with a light fluence of 3-5 [J/cm²].
Each treatment pulse should be applied
on different skin spot with no repetition
or overlap. The entire treatment area
(underarms, bikini line, arms, back,
shoulders, chest, legs and allowed facial
areas) will be determined by the user.
Notes:
1. Response to sensiLight™ Mini hair
reduction differs between individuals,
depending on biological factors.
2. sensiLight™ Mini works best on dark
hair or hair that contains more melanin.
Brown and light brown hair will respond,
but typically will require more treatment
sessions. Red hair may show some
response. White, grey or blond hair shows
a more limited response.
3. It may take up to 3-4 weeks before the full
results of the sensiLight™ Mini treatment
can be seen. Hair will continue to grow,
up to two weeks after a hair reduction
session. However, afterwards, as the hair
grows in three different stages, it will
naturally and gradually fall out depending
on the hair growth stage in during which
the treatment was performed. Some hair
may not be affected by sensiLight™ Mini
as of the different hair growth phases-
only hairs in the active growth phase will
be affected. To remove this hair multiple
treatment sessions are required to
achieve the desired results.
• The number of sessions required for
achieving long term results is different
for every treatment area and changes for
every user, as it is affected by type of skin,
hair and hormonal changes.
• Maintenance will be needed from time to
time if growth is still visible.
• You may use the treatment log at the end
of this User Guide, in order to assist you
with recording your specific treatments
areas, dates and duration.
English

Facial treatment
The facial skin is a sensitive area that
requires special care and caution. Make
sure you follow all instructions and safety
precautions carefully in order to avoid
adverse effects.
It is recommended you first do a body
treatment and get to know the device,
before moving on to facial treatments.
sensiLight™ Mini can be used to treat all
facial areas below the cheek line such as
upper lip, cheek, jaw, chin and neck.
WARNINGS
• Do not use energy level higher than level 2
since it may cause burns.
• Do not use sensiLight™ Mini on the face
above the cheek line or
around the eyes, eyebrows
and eyelashes as this could
cause serious eye damage.
1. Mark the treatment area with a white
eye pencil. Use the mark as guidance
for delivering the pluses. This way you
can avoid overlapping treatment areas
or treating unwanted facial areas.
2. Use a mirror to help you place the
treatment window correctly on the
treatment area.
3. Follow the instructions for use with
additional care to the following
specific area instructions.
Note:
Facial hair may be hormonal and as such,
it can take more sessions to achieve a
permanent hair reduction.
16
English

Upper lip, cheek, jaw, neck and chin
treatment
Place the treatment window (see image
– item 7) on the area as indicated in the
picture. Trigger one pulse on each spot.
Upper lip:
Avoid the nostrils and lip, as
these areas are more sensitive.
You can“fold”your lip inward
or press the lips together
to achieve a better spread
treatment area.
Cheek and jaw:
Place the treatment window
on the area as indicated in the
picture. Trigger one pulse on
each spot, moving from one
side of the jaw/cheek to the
other.
Neck and chin:
Place the treatment window
on the area as indicated in the
picture. Trigger one pulse on
each spot, moving from one
side of the neck/chin to the
other.
Note:
The skin on lower third of the neck is more
sensitive. Avoid from overlapping treatment
areas.
For male users
Take care while treating the beard area;
the density of hair growth means a large
amount of melanin which absorbs the heat.
It is recommended performing the first
treatment in low energy levels (1-2).
It is not recommended to do a full beard
reduction as it may change the facial
characteristics and result in a feminine look.
Note:
Premature aging characteristics can
emerge due to complete loss of facial hair.
17
English

1818
What to expect when using
sensiLight™ Mini
During your hair removal treatment it is
normal to experience:
• A flash of light on each press of the
activation button. The light will not harm
the eyes when the device is applied
with full contact to the skin on the
recommended treatment areas.
• A pop noise with each pulse – occurs
whenever a pulse is activated.
• A sensation of warmth – radiates from the
light energy after each pulse.
• A mild stinging sensation – can be felt,
similar to being snapped with a rubber
band.
• Some mild red or pink color – appears
during and just after the treatment.
Post-treatment care
• Apply a calming lotion such as Aloe Vera.
We recommend you to use Sensica post
treatment lotion for increased treatment
efficacy and best possible results.
• Avoid using peeling and bleaching creams
or products for at least 24 hours, as this
irritates the treated skin.
• Avoid direct sun exposure for at least 2
weeks post treatment. If recently treated
skin is exposed to sunlight in this period of
time, make sure to apply SPF 30 or higher
sunscreen.
• Do not wax or pluck hair from treated areas.
Remember! It may take up to 2 weeks for
the hair to grow and be fully out, if the hair
follicle is still active.
Cleaning and
troubleshooting
Cleaning
• Make sure to turn off and unplug the unit
before cleaning.
• It is recommended to clean the treatment
window after every session by using a dry,
clean cloth to gently wipe the device.
• Keep sensiLight™ Mini dry. Never place,
store or use sensiLight™ Mini near
bathtubs, showers, basins or other vessels
containing water as this may cause severe
electrocution.
• If you do not plan on using your
sensiLight™ Mini for a long period of time,
it is recommended to keep it clean and
stored.
• If you plan to travel and take your
sensiLight™ Mini with you, you should
store it in the original box and follow the
storage instructions.
English

1919
Troubleshooting
If you experience any problems with
sensiLight™ Mini, please refer to below
information to try to resolve it.
• If sensiLight™ Mini does not turn on:
• Make sure that the power supply is
plugged properly into sensiLight™ Mini
device and the electrical outlet.
• Make sure the power outlet has power.
• If sensiLight™ Mini does not trigger a pulse:
• Verify there is full contact with the skin.
The trigger button will activate a flash
pulse only when the device is in full
contact with the skin.
• Verify that the area you are trying to
treat is not too small, curved or bony
to treat. You should get the whole
treatment window in touch with the
treatment area (try to pull the skin flat).
• If the skin color level identified by
sensiLight™ Mini is too dark, the flash
activation will be blocked.
• In case of a safety issue or when the
lamp has reached its end, a steady red
light will come on. The device will shut
down.
General error:
• In case of dirt or debris is stuck on the
treatment window, you should clean
the treatment window according to the
cleaning section. If you can’t get the area
clean, contact our customer service.
• In case of a delay in pulse readiness,
you should consider working in cooler
environment. The device may pulse at a
slower rate in warm environment.
• In case of a general error, reset the
device – unplug the power cord from
the electrical outlet on the wall, wait 10
seconds and then reconnect it .
• If you still have problems with your
sensiLight™ Mini, please contact
customer service.
Customer service
For more information about sensiLight™ Mini
or if your sensiLight™ Mini is broken, quits
working or you need more assistance, please
contact your local Sensica customer service or
visit our website:
@www.sensica.com
English