SHADE SCAPES AMERICAS CONCRETE MOUNT KIT User manual

1
Once installed, always use COMMON SENSE WIND GUIDELINES: If it is too windy to be outside enjoying the day, it is best to lower/collapse the
Umbrella Frame w/ Fabric Canopy. It is also important to keep it lowered/collapsed when unattended. See manufacturer's limited warranty on
page 2.
Please thoroughly read this installation manual before installing the Concrete Mount System, and before assembling and operating the Umbrosa
Umbrella. The Umbrosa Warranty does not cover damage caused by incorrect installation, wind, or wrongful use of the product. All users must be
properly trained in operation and wind guidelines.
A COMPONENTS LIST & REQUIRED TOOLS
1X - BASE PLATE (BP)
Box A
4X - 10x16mm SPIGOT BOLTS (A2)*
1X - 6mm ALLEN WRENCH (T2)*
Box A
*PLEASE NOTE THE SPIGOT BOLTS AND 6mm ALLEN WRENCH
ARE LOCATED IN THE CONCRETE MOUNT BOX, BUT WILL
NOT BE USED UNTIL YOU BEGIN TO INSTALL THE UMBRELLA
SEE YOUR OWNERS MANUAL FOR DETAILS.
CONCRETE MOUNT KIT
INSTALLATION MANUAL
Sleeve (A1a)
(A1b)
4X - 3/8"x3-3/4" CONCRETE SLEEVE BOLTS (A1)
1X - 7/32" ALLEN WRENCH (T3)
1X - 3/8" CONCRETE DRILL BIT (T4)
Box A
REQUIRED TOOLS LIST (not included):
Standard Electric Drill
Aerosol Compressed Air or Shop Vacuum
Carpenter's Level
Hammer, Pencil

UMCMK‐SSA2015.01
Umbrosa NV warrants to the consumer that the Spectra product is free from manufacturer defects in material or workmanship for a period of three (3) years from the
date of original purchase when used in compliance with directions as outlined in the manufacturer’s instructions, which includes reasonable and necessary
maintenance by the consumer. Warranty does not include normal wear and tear of product. Umbrosa takes no responsibility for incorrect use or assembly related to
installation area, consistency of supports and relative hardware used, and capacity of mounting surfaces. Failure to follow the given assembly, maintenance, use and care
instructions will void the product warranty. In case of manufacturing defects in material or workmanship, Umbrosa NV, agrees to, at their discretion, send the replacement
part for all defective parts.
3:
(a) Gently hammer the Concrete Sleeve Bolts (A1) into
the concrete leaving them flush with the surface.
(b) Once flush, use the 7/32" Allen Wrench (T3) to
remove the four (4) Flat Head Screws (A1b) from the four
(4) Sleeves (A1a).
(c) The Sleeve is shown flush with the surface.
2:
The Concrete Sleeve Bolts (A1) in combination with the Base Plate
(BP) require a minimum concrete depth of 4" for optimal
anchorage. Determine a level location to install and check surface
using a Carpenter's Level.
(a) Using the Base Plate (BP) as a template, mark the four (4) hole
locations on the patio surface. (b) Placing the point of the Concrete
Drill Bit (T4) into the center of the mark, drill four (4) vertical holes
to a depth of 3-3/4". Clear out debris from the hole using either
Aerosol Compressed Air or a Shop Vacuum.
Note: The Spigot (SR1), and Pole (SP2) referenced in the
diagram to the right may be packed separately from the
Concrete Mount Kit. This diagram is for reference only and
these parts are not needed until the Concrete Mount Kit has
been installed.
4: (a)
Align the countersunk holes in the Base Plate (BP) with the
four (4) Sleeves (A1a).
(b) Use the 7/32" Allen Wrench (T3) to insert the four (4)
Flat Head Screws (A1b) into the four (4) Sleeves. Tighten to
completely secure the Base Plate to the surface.
(c) The Spectra Concrete Mount Kit is now installed.
2
You are now ready to mount your the spigot for your Umbrosa Umbrella to the Concrete Mount Kit. Locate the
Owners Manual for the product you purchased, and use those instructions to complete your installation.
B MOUNTING INSTRUCTIONS
Consult your local contractor if you have any questions regarding
your particular installation.
1:
The Base Plate (BP) has four (4) countersunk holes and
four (4) tapped holes. For Spectra and Paraflex
umbrellas, line up the tapped holes SQUARE to
whatever you are aligning your Umbrella with, for
example your house, edge of patio, etc., as shown in
the diagram to the right.
Distributed by Shadescapes Americas www.shadescapesamericas.com; 818.217.4446. For assembly assistance or questions
please contact ShadeScapes Americas at 970.527.7070, or email [email protected].