SHANGRI-LA ROBIN SLROBI4CDWA User manual

ROBIN CHEST OF 4
DRAWERS
SLROBI4CDWA & SLROBI4CDBA

Please read these safety instructions thoroughly before using this product. Retain this guide
for future reference.
• Carefully identify each component, especially those that are similar. The most
common mistake is getting things back to front.
• Separate and identify each component from the hardware pack and rest it in its
final location before fastening.
• Do not fully tighten screws (leave slightly loose). When the item is fully assembled
tighten the screws - but do not over tighten.
• If glue is required, do not set until you are certain that the parts belong together.
SAFETY & WARNINGS

Lay all components out on a clean floor and ensure all parts are included. If any pieces are
missing, check all packaging thoroughly, then contact help.Kogan.com for assistance.
Parts:
COMPONENTS

No.
Size (mm)
Qty
No.
Size (mm)
Qty
1
60 x 395 x 40
1
12
50 x 552 x 15
2
2
60 x 395 x 40
1
13
50 x 224 x 15
2
3
60 x 395 x 40
1
14
46 x 770 x 15
1
4
60 x 395 x 40
1
15
46 x 770 x 15
3
5
394 x 795 x 15
1
16
190 x 766 x 15
3
6
394 x 795 x 15
1
17
190 x 766 x 15
1
7
394 x 722 x 15
1
18
130 x 350 x 12
4
8
394 x 722 x 15
1
19
130 x 350 x 12
4
9
398 x 869 x 2.5
1
20
128 x 726 x 12
4
10
398 x 869 x 2.5
1
21
344 x 735 x 2.5
4
11
80 x 770 x 15
1
22
50 x 335 x 12
8
Hardware:
AØ15x9.6 (x55)
B35mm (x55)
CØ4x25 (x12)
DØ4x32 (x8)
E14" (x8)
F14" (x8)
GØ3.5x12 (x48)
H(x32)
IØ5.5x38 (x4)
JLegs (x4)
KØ5x16x1
L
MØ5x16
NØ842

IMPORTANT! Read before assembling
This product contains multiple sets of metal slide runners and slide tracks (shown separated
above).
To a v o i d d a m a g e to t h e s e i t e m s d u r i n g t ra n s p o r t a t i o n , t h e s l i d e r u n n e r s a n d t r a c k s h a v e
been pre-assembled together in pairs. Each pair includes one slide runner and one slide
track.
Before assembling your furniture, separate the runners from the tracks according to the
following instructions:
• Extend the slide runners.
• Gently press the plastic release lever on the slide runner while pulling the slide
runner and slide track apart from each other.
• The slide runner and slide track should now be separated. Repeat these steps for
the remaining pairs of slide tracks:
ASSEMBLY
Slide runner
Slide track

Step 1:
B35mm (x24)

Step 2:
F14" (x8)
GØ3.5x12 (x24)
x4 Drawer Slides F
x4 Drawer Slides F

Step 3:
AØ15x9.6 (x6)
DØ4x32 (x8)
Arrow to point in
the direction of
end hole

Step 4:
AØ15x9.6 (x12)
Step 5:
AØ15x9.6 (x2)
Arrow to point in
the direction of
end hole
Arrow to point in
the direction of
end hole

Step 6:
AØ15x9.6 (x4)
Step 7:
CØ4x25 (x6)
Arrow to point in
the direction of
end hole

Step 8:
B35mm (x7)
Step 9:
KØ5x16x1
L
MØ5x16

Step 10:
CØ4x25 (x6)
Step 11:
B35mm (x4)

Step 12:
E14" (x8)
GØ3.5x12 (x24)
x8 Drawer Slides E

Step 13:
B35mm (x10)

Step 14:
AØ15x9.6 (x5)
Step 15:
AØ15x9.6 (x5)
Arrow to point in
the direction of
end hole
Arrow to point in
the direction of
end hole

Step 16:
B35mm (x8)
JLegs (x4)

Step 17:
AØ15x9.6 (x4)
Step 18:
AØ15x9.6 (x4)
Arrow to point in
the direction of
end hole
Arrow to point in
the direction of
end hole

Step 19:
AØ15x9.6 (x2)
B35mm (x2)
IØ5.5x38 (x4)
Arrow to point
in the direction
of end hole

Step 20:
AØ15x9.6 (x4)
Arrow to point in
the direction of
end hole
Stand upright

Step 21:
AØ15x9.6 (x7)
Arrow to point in
the direction of
end hole