Salamander Designs SYNERGY SA/MD User manual

SYNERGY MEDIA DRAWER - SA/MD
SU20
MAX DRAWERS=2
*No Adjustable Shelf on Top Drawer
DRAWER 1
SU30
MAX DRAWERS=3
DRAWER 1
SU40
MAX DRAWERS=4
DRAWER 1
SHELF
SHELF
SHELF
GAP = 1.625”
GAP = 1.625”
GAP = 1.625”
GAP = 1.625”
GAP = 1.5”
GAP = 1.5”
GAP = 1.5”
GAP = 1.5”
GAP = 1.5”
SHELF
SHELF
SHELF
SHELF
SHELF
17.75”
27.75”
37.75”
(300-665)
Fixing Hook
2x 2x
Parts
1 - Drawer Face (200-630)
2 - Metal Drawer Slides
Metal Drawer Slides
1 - Bottom Panel (200-640)
1 - Drawer Back (200-650)
2 - Drawer Brackets (300-640)
6 - C/S Rivets
6 - Backup Washers
Drawer Spacer Tool
Use the Spacer Tool (included with base unit) for reference when
spacing drawers. Refer to these measurements when installing
2 drawers on a SU20, 3 drawers on an SU30 or 4 drawers
on a SU40.
5x
(300-110)
No. 6 Screw
11x
(300-115)
Black Screw
(300-685)
Cover Cap
Shelf Bracket Bag
PHK-150
4x
4x
(300-490)
Low Head Screw
(300-610)
Rubber Tab
4x
(300-560) - Flat Nut
Bottom Panel
Drawer Back
Drawer Side
Drawer Side

Doc No. 500-380/v2014 ©2014 Salamander Designs Ltd.
Limited Warranty
For ve full years Salamander Designs Ltd will repair or replace, at our option, any product defective in materials or craftsmanship. Salamander Designs Ltd. will not be responsible for any damage to or destruction of other
equipment consequential to our equipment failure. Defective product must be given Return Authorization and is to be returned to the factory prepaid, in the original carton and packing material. Any damage incurred in a
shipment not in original packaging shall be the responsibility of the owner. Warranty repairs will be returned prepaid, via UPS within the continental U.S.A. only.
1Installing Multiple Drawers
12 3 45 6 7 8 9
REAR PANE L
4 1/2 "
6
8
www. s a l a ma n de r de s i g ns . c o m
REAR PANEL
REAR PANEL
SPACER
TOOL
Note: Position the top of the Tool along the top of the rst set of drawer
slides and set the next set of drawer slides to align along the bottom of
the Door. Tighten each set of drawer slides.
Adjustable Shelf
Note: The length of the Spacer Tool equals
the amount of space between drawers.
Salamander Designs Ltd. 800.535.5659 www.salamanderdesigns.com

2Insert Drawer Slides
3Layout Sides
Place the sides parallel to each other with the rollers on the top outer corners.
Place Bottom
Place the bottom panel in between slides with the rounded edge facing
forward and make sure the pre-drilled holes are on the underside. Match the
bracket holes with the pilot holes and attach six black screws from bottom.
4
A.Place the low heads in the 2 holes of each
drawer slide and attach loosely.
B.Insert the weld nuts into the channels
making sure that the rollers face the front of
the rack. Use the Spacer Tool provided and
the instructions on opposite side to help space
the drawer(s) as desired.
C.Insert the Rubber Tabs into the 2 holes
on the shorter part of the bracket with the
at side facing up.

R
R
L
5Insert Back Panel
Drop the back panel into place, rounded edge up, matching pilot holes
with holes on the brackets and attach black screws from behind.
Drawer Face
Height Adjustment
Screw
7Attaching Panels 8Adjust Height and Add Trim Cover
Add Fixing Hooks to Drawer Face
6
REAR OF DRAWER FACE
NOTE:
The two xing hooks that attach to
the front panel are dierent. Each
Bracket is marked “R” or “L”.
Adjustment screws on the xing hook should face outside of the drawer box.
Tighten Bracket
with this Screw
Slip the bracket onto the drawer sides. Tighten inset screw to tighten clamp
bracket to drawer side.
Note: To adust drawer height, turn outter screw to left or right.
Apply trim cover to bracket.