Sharp ES-W90HT User manual

Name of each component
Key points of washing
Instruction on control panel functions
Instruction on washing courses
Self-decided washing course
Maintenance
Common non-fault phenomenon
Specification
Table of contents
Safety precautions
2
Operation manual
Thank you for purchasing our product.
Please read this manual carefully before use.
Please read “Safety Precautions” carefully
before use.
Please keep this manual in a safe place.
Our product is specially designed for household
use only.
Page
4
5
6
8
9
10
11
13
15
18
Additional operating procedure
Things to know before washing
Printed in Indonesia
TINS-A277QBEZ
Operation manual of full-automatic washing machine
ES-W90HT
SHARP CORPORATION
OSAKA, JAPAN
ES-W80HT
จัดพิมพ์โดยประเทศอินโดนีเซีย

Safety precautions
FORBIDDEN
WARNING
FORBIDDEN
INFLAMMABLES
GASOLINE
FORBIDDEN
FORBIDDEN TO
USE AT
HIGH-HUMIDITY
LOCATIONS
MANDATORY
FORBIDDEN
TO
TOUCH
MANDATORY
FORBIDDEN
TO
WASH THE WATER
FORBIDDEN
FORBIDDEN
FORBIDDEN
2 19
MEMO
DISASSEMBLE
FORBIDDEN
PULL OUT
THE PLUG
Do not allow children to play
with or look around the
wash-spin dry tub,
It is very dangerous.
Clothing stained with flammable or explosive
substances such as gasoline, kerosene and
so on must not be put
into the wash-spin dry tub.
Never put your hand inside the tub
while it is still moving. Even if
the tub is moving at low speed,
your hand may get wrapped up
and get injured. Wait until the machine
completely stops. Special attention
should be given to children.
Do not use power supply other than
AC220V, 50Hz, so as to avoid malfunction,
damage and fire.
Except service staff, do not modify the machine.
Please do not disassemble and
repair the machine without permission,
so as to avoid fire, electric shock,
getting hurt or malfunctions of the machine.
Do not place the machine at high-humidity
places such as bathroom, locations where
wind and rain may get in, and so on.
Otherwise, electric shock,
fire, malfunctions and
distortion may take place.
Use plug socket above 13A separately.
A loose plug socket cor the action of
sharing a plug socket with other equipments
may start a fire due to heat.
When cleaning the machine body,
the plug should be pulled out first.
Do not plug or pull the plug with wet hand or
wet cloth, so as to avoid electric shock. Clean the dust on the plug
and plug socket to avoid fire.
Do not approach any fire
source to plastic components,
which has the risk of starting
a fire.
Do not use water to wash
components of the machine,
so as to avoid short circuit
and electric shock.
Do not use damaged power
cable, plug or loose plug
socket, so as to avoid short
circuit, electric shock, fire
and other accidents.
Do not change the original
state of power cable. Any
visible damage to the power
cable could cause electric
shock, electric leakage or
other malfunctions.

18
Specification
3
WARNING
FORBIDDEN CAUTION
DO NOT PUT
WATER-RESISTANT
ITEMS INTO THE TUB
FORBIDDEN
The temperature of water must
not exceed 50℃, so as to avoid
accidents of electric leakage and
electric shock due to distortion or
damage of plastic.
FORBIDDEN
MANDATORY
MANDATORY
FORBIDDEN TO
TOUCH
MANDATORY
MANDATORY
FORBIDDEN
MANDATORY
Safety precautions
Standard washing / spin
drying capacity
Washing / Spin Drying
Rated Power Input
Model
Power supply
Water pressure
Weight
Dimensions (W×D×H (mm))
Standard water consumption
Standard water level
Washing type
Do not connect to the hot water supply.
CAUTION
The new hose-sets supplied with the appliance are to be used and that old hose-sets should not be reused.
ห้าม ข้อควรระวัง
ห้ามนำเสื้อผ้ากั
นน้ำใส่ในถังซัก
า้ฟฟไ้ชใงอืรคเบักมอ้รพามีท่มหใดุชอ่ท้ชใ ่มหใ้ชใามบัลกา่กเดุชอ่ทำนรวค่มไะลแ
ES-W90HT ES-W80HT
220V ~ 50Hz
9.0 kg 8.0 kg
Swirl type
0.03 ~ 0.8 MPa
530 × 585 × 993 530 × 585 × 963
340 W / 205 W
29 kg
65 L 62 L
124 L127 L
410 W / 205 W
124
62
65
127
9.0 8.0
340 205
410 205
PULL OUT
THE PLUG
Do not wash water-resistant items.
Do not wash sleeping bags, shower
curtains, raincoats, rain ponchos,
rain covers, ski jackets, ski pants,
automobile covers and other water
-resistant items, so as to avoid
abnormal vibration and other
unexpected accidents /malfunction.
Do not wash objects other than
clothing to avoid abnormal
vibration which causes damage to machine.
When pulling out or plugging
the plug, do not touch the metal
part of the plug to avoid electric
shock or short circuit.
After using the washing machine,
pull out the plug to avoid electric
leakage, electric shock or fire
due to loose connection of plug.
Before using, check carefully if
the connection of water inlet
hose and drain hose is reliable,
to avoid water leakage.
During spin drying, the washing tub is rotating
at high speed. Because water in water-resistant
clothing could not be discharged instantaneously,
the machine will be out of balance, causing abnormal
vibration and other unexpected accidents /malfunction.
When the machine is operating,
do not touch the bottom with
hand or foot, where there is
a rotating mechanism, so as
to avoid getting hurt.
Before using, check the
bottom of the product, make
sure there is no packaging
material left.
Do not put heavy objects on the machine.
It may cause distortion and damage.
The base opening must not
be obstructed by a carpet
when installing the washing
machine on the carpeted floor.
After using, turn off the faucet
to avoid water leakage.
To avoid accident /injury, if the power cord is damaged, it must only be replaced by an authorized
service staff or contact the nearest Sharp Service Center for assictance.
If powder detergent or liquid detergent spill over the top cover, or other plastic components,
wipe it away immediately, otherwise it may damage them.
Each time washing is finished, clean lint filter box. Otherwise it may not be effective in filtering lint.

Name of each component
Machine body
List of accessories
Name Quantity
Water inlet hose assembly 1 set
Drain hose 1
Operation manual
Bottom cover ※1
1
Screw ※1
174
Common non-fault phenomenon
Inspection of a washing machine having been used for many years.
Check Are there
situations
like these?
Does not run sometimes.
Water leakage (water hose, spinning tub,
tap connection).
There is burnt smell.
There is an abnormal sound or vibration
during operation.
Your hand feels numb while touching
the machine.
Power cable or plug is unusually hot.
Stop using
the machine
“CHILD LOCK” does not work during
operation.
Installation manual
1
Warranty card 1
Top cover
Adjustable foot
Control panel
Water inlet hose
connecting port
Power cable
Pulsator
Lint filter box
Cabinet
Drain hose
※BottomcoverandScrewareappliedbyServicestaff.
Not a fault
Phenomenon
Others
There is a noise on the
radio or television, and the
image is unclear.
Keep the washing machine away from radio
and television as far as possible.
After washing is finished,
there are white lines around
the washing / spin drying tub.
The white powdery material is the result of the
combination of ingredients in detergent and
ingredients in water. (Wipe away with cloth.)
Please note that it will stick on where it is left.
Using liquid detergent or injecting water and rinsing
twice can prevent this phenomenon.
Not working.
Light cannot be on.
Is the power cord properly plugged in?
Is the power supply interrupted or is the main
switch in your house turned off?
There is abnormal sound.
Is the washing machine inclined or is it unstable?
Does the clothing deviate to one side during spin drying?
Are there hair clips or other foreign metal objects
mixed in the clothing?
No water inlet. There is no water supply if the top cover is open.
Please close the top cover properly.
Tap leaks.
Are the screws or the installation position of the
water nozzle connection loose?
Is the water nozzle connection inclined or wobbly?
ไม่ใช่อาการผิดปรกติ
To avoid injuries or accidents, please pull
out the plug from the plug socket.
Call the nearest Sharp Service Center
to check your machine. Consult Sharp
Service Center for check and repair fees.
ฝาครอบด้านล่างและสกรูจะต้องติดตั้งโดยผู้ชำนาญงานเท่านั้น

516
Key points of washing
Pay more attention to the following situations
To avoid damage to tub
and pulsator...
To avoid damage to clothing,
winding of clothing...
For better washing... To protect the environment
While using a washing mesh bag, put in as little clothing as possible. Too much clothing will decrease
the performance during rinsing and spin drying or cause the offset of clothing during spin drying.
Common non-fault phenomenon
Water
inlet
ไม่ใช่อาการผิดปรกติ
Put bra etc. in the washing mesh bag.
Take out coin, hair clip,
curtain hook out of pockets.
Turn clothes with zipper and
metalic buttonsinsideout
Metal decorations (zippers etc.) on the clothing
in washing mesh bag must be checked.
Belts on apron and so on must be knotted;
zippers must be zipped.
Thin or easily damaged clothing must be
washed in washing mesh bag.
For towels and other clothing,which
easily produce lint,wash them
separately or usewashing mesh bag.
Please check the washing mark.
Wash clothes separately that are easy to fade.
Reuse wash water.
During washing, wash clothing together.
Put in proper amount of detergent
according to the fouling situation.
...To avoid the waste of water, detergent
and electricity.
Phenomenon Not a fault
Washing
Rinsing
Others
Sound in water hose and water
inlet valve.
Spinning
When washing or rinsing is finished,
the pulsator will rotate slightly.
During the washing process, the pulsator
rotates intermittently.
The pressure of tap water is relatively high.
Adjust amount of water.
To reduce vibration caused by offset of clothing
during spin.
In the soaking and washing in soak course, the
pulsator rotates once every 8 seconds, so that the
detergent can permeate into the clothing sufficiently.
When spinning starts, low-speed rotation
will happen for a while.
(Not rotating at high speed immediately)
This action is done to adjust the balance and to
dry clothing sufficiently.
When spinning starts, the machine
gives off sounds like “Patsa Patsa”. During spin drying, water hits the tub side, which is
not abnormal.
During spinning process, the program
starts supplying water and rinsing.
(Spin light indicator blinks quickly.)
During the rotation in spin drying, unbalanced load
is detected and corrected automatically.
(If the offset phenomenon cannot be changed by
auto-correction, the operation will stop immediately.)
The clothing has been spin
dried but not wringed dry.
The spin drying ratio of an automatic washingmachine is a little lower
than that of a twin tub washing machine. In case the spin drying
of large clothing such as towels, blankets etc.
is uneven, spin drying it again.
Operating parts is heated. It is caused by the heat radiation of electrical
components.
Indoor lighting darkens
temporary.
The voltage of plug socket in your house drops
temporary when the motor starts up.
(Please use an exclusive plug socket.)
There is a sound of water
when tub body is rotated.
To keep balance during spinning, there is liquid in
the balance ring.
The detergent is dissolved
in the detergent case.
If tap water pressure is low, detergent tends to remain, so please
dissolve it in water beforehand and put it directly into the tub.
Can not rinse thoroughly.
In the "NORMAL" course the rinse is "ECO SHOWER RINSE",
so if the tap water pressure is low, the ability may decline.
If you are concerned, you can change to Normal Rinse by
"MANUAL OPERATION" (see page 10) and you can rinse thoroughly.
Before washing, please remove mud and sand on clothing first.
For very dirty parts of the clothes, smearing some liquid detergent
and rubbing them in advance may help.
For clothing that are easy to be torn, turn it inside out first and then wash them.
Clothings which are heavy (Jeans, Big size clothings)
and easy to float (Socks, Handkerchieves, Fleece, Jackets)
should be put into the washing machine first
for a effective rotation of the clothes inside the appliance.
ผงซักฟอกจะละลาย
โดยใส่ผงซักฟอกในกล่องผงซักฟอกเท่านั้น หากแรงดันน้ำประปาต่ำ น้ำจะไม่ไหลผ่านช่องผงซักฟอก
ให้แก้ปัญหาโดยใส่น้ำลงในกล่องผงซักฟอกโดยตรง
ไม่สามารถล้างน้ำได้โดยตรง การเลือกฟังก์ชัน "ECO SHOWER RINSE"
หากแรงดันน้ำประปาอยู่ในระดับต่ำความสามารถอาจลดลง
หากคุณกังวลคุณสามารถเปลี่ยนเป็นการล้างน้ำ ปกติได้โดยสามารถดู
"คู่มือการใช้งาน" (หน้า 10)
เสื้อผ้าที่มีน้ำหนักมาก (กางเกงยีนส์, เสื้อผ้าจำนวนเยอะ)
หรือมีน้ำหนักน้อยเช่น (ถุงเท้า, ผ้าเช็ดหน้า, ขนแกะ, แจ็คเก็ต)
ควรใส่ลงในถังซัก ก่อนถังซักเริ่มทำงาน

Instruction on control panel functions
Control panel / Display
6
WASH
RINSE
SPIN
NORMAL
JEANS
SPEEDY
DELICATE
BLANKET
TUB CLEAN
Wash heavy and very dirty clothing.
Wash speedy for Not-so-dirty clothing.
POWER
Course for cleaning washing / spin drying tub. Select the washing time: 2 hrs, 6 hrs, 9 hrs.
Caution
START/PAUSE
Press this key after turning on, selected course is started.
Plug the machine in and then press this key, the machine turns on.
Press this key again, it turns off.
If the machine is energized but not started, the power supply turns off automatically 5 min later.
Wash clothing with the HAND WASH mark.
Wash daily clothing like relatively-dirty shirts or pants.
Wash strong for blankets or heavy clothing.
Select WASH as necessary. Select the washing time: [ - ](= 0 min) ,3 min – 15 min.
Select RINSE as necessary. Select the rinsing time: [ - ](= 0) ,1 time – 3 times.
Select SPIN as necessary. Select the spinning time: [ - ](= 0 min) ,1 min – 9 min.
BABYCARE
Wash gently and rinse thoroughly for baby clothing.
15
Common non-fault phenomenon (Please refer to this section
if you think an abnormality happens.)
Abnormal display
Presentation
U9
E4
E3
E2
E1
C2
Washing machine inclines
or is shaky.
The clothing is lopsided.
The end of drain hose is
blocked.
The drain position is
relatively high.
Top cover is not closed
during spin drying.
Possible non-fault cause Coping process Failure cause
Low flow at the faucet.
Water inlet filter net
is blocked.
Because the phenomenon may not be a fault, please check it again before sending the machine
for repair. In the case of failure, please consult the maintenance department. Be sure not to disassemble and
repair the machine without permission.
Caution
List of failure cause
Water level sensor shows
an abnormal level.
Failure of water inlet
valve
Connector contact
failure
Wiring disconnection
Failure of safety switch
Failure of drain valve
Failure of drain valve
motor
Circuit failure
Get water in tube of
water level sensor
Connect failure on
drain valve motor
The faucet is closed.
Top cover is opened as the
reservation course starts.
Drain hose is folded/
crumpled/tied.
Inclease water supply, press
START / PAUSE key.
Turn the faucet on, press
START/PAUSE key.
Failure of water level
sensor
Clean filter net, press
START/PAUSE key.
Close top cover.
Adjust drain hose properly,
press START/PAUSE key.
Clean drain hose, press
START/PAUSE key.
Washing machine place the
horizontally with adjusting the
foots.
Distribute the clothing evenly.
Pull out the plug from the plug
seat, and entrust the main-
tenance department.
Top cover opened in the
situation of CHILD LOCK.
Turn the power off, and take it
from the top.
CHILD LOCK is not released,
unless you reset it manually.
Caution
[ - ](= 0), 1
[ - ](= 0 ) ,3
[ - ](= 0 ) ,1
กรณีพบความผิดปกติของเครื่อง ให้ปรึกษาศูนย์บริการหลังการขาย
ห้ามแกะซ่อม ตัวเครื่องเอง โดยไม่ได้รับอนุญาติ

7
Instruction on control panel functions
Control panel / Display
Additional
function
14
Course for reducing the time to dry.
AIR DRY Spin-drying with high-speed takes air into the inner tub from the hole of top lid.
AIR DRY course reduce the time to dry in the shade greatly.
Select the time:
[ - ](= 0 min) , 30 min, 60 min, 90 min.
Select the appropriate water level depending on course or kinds of clothing.
(Select from 8 steps regulation)
WATER LEVEL
SOAK
FRAGRANCE
CHILD LOCK
AUTO CLEAN
The washing machine displays the water level at the beginning of running.
The washing machine displays the remaining operation time during the operation.
The washing machine displays reserved time during the RESERVE course running.
The washig machine displays a presentation in the page 15, when an abnormality happens.
RESERVE
It is possible to operate only POWER key and START/PAUSE
key in this mode.
TUB CLEAN
Maintenance
In the case of cleaning the washing / spin drying tub.
Do not put the clothing in the tub in this course.
Caution
[ - ](= 0 )
Press Power ON/OFF key
with the top cover closed.
2
3
Press COURSE key,
and select TUB CLEAN course.
Press WASH key, and select the washing time.
Press WATER LEVEL key, and select the water
level as necessary.
4
Press START/PAUSE key.
The washing machine starts to supply water,
and displays remaining operation time.
1
Put the washing machine cleaner for
cleaning the tub.
Reserves the time as desired. Select the time: 1 hr – 24 hrs. Reserved time
indicates the time to finish the operation. It means, the operation finishes
1 hour later when 1 hr is selected. Set the time after selecting the necessary course.
When SOAK course is selected, the light is turned on. During soaking,
the water in the tub is stirred intermittently. Select the soaking time: 5 min – 24 hrs.
This function can be added to every course except for TUB CLEAN course.
This function enhances softener’s efficacy. Extra soaking time will be added
before the last rinsing process to enhance the softeners efficacy.
The clothing will be soaked in the water with softener.
CHILD LOCK is set by holding down FRAGRANCE key for 3 sec. This function is
to prevent children and infants from drowning. The error tone can be heard
if top cover is opened after water supply start. If top cover has been opened for
30 sec in such condition, the water is automatically drained.
AUTO CLEAN is set by holding down WATER LEVEL key for 3 sec.
(Removes the dirt in the washing / spin drying tub and the back side of pulsator
with clean water at the final spinning.)
ฟังก์ชั่นนี้ช่วยเพิ่มประสิทธิภาพของน้ำยาปรับผ้านุ่ม จะเพิ่มเวลาการแช่ผ้าเพิ่ม
ก่อนกระบวนการล้างครั้งสุดท้ายเพื่อเพิ่มประสิทธิภาพของน้ำยาปรับผ้านุ่ม

Tub side
138
Things to know before washing
Select the course depending on kinds of clothing or degree of dirt on clothing.
After pressing START/PAUSE key once, you can not change the course. When you
want to change the course, turn off the power and select the course as desired again.
Blinking display indicates the step in running, lighting display indicates the course
selected.
When motor get hot beyond a safe limit, it fail-safes on it, and can’t work enough.
Do not operate the machines more than 3 times in a row.
When the motor is overheated,
the operation continues, but
the motor will not work properly.
After it is cooled down,
it can be used normally.
Maintenance
Lint filter box
Clean it each time washing is finished.
4. Press START
/PAUSE key.
1. Detach lint filter box from washing tub. 2. Clean lint filter box and the
tub side. 3. Attach lint filter box on washing
tub to a downward direction.
1. Turn off
the faucet.
2. Turn on the
power and
press WATER
LEVEL key.
The water in the hose has been
draind about 10 min later.
Then turn off the power.
5. Dismantle water
inlet hose.
Caution
6. Clean the filter net.
Water inlet hose connecting port
Washing / Spin Drying tub
1. Every time after washing, turn off the faucet and power. (If necessary,
dismantle water inlet hose.)
2. Wipe the water in the tub after washing as soon as possible. Use clean soft cloth.
3. Be sure to pull out the plug from the plug socket during maintenance.
4. Hanging power cord and drain hose is desirable.
5. Open top cover for about 1 hour after cleaning the tub.
6. Do not use solvents such as alcohol, cleanser and so on, because they may cause damage
to the surface of the tub.
Remove the filter net
and clean it.
Twist connecting part,
not hose.
Caution
ECO SHOWER RINSE
The program in the "NORMAL" course is the "ECO SHOWER RINSE".
It can rinse by supplying water while rotating the tub, so it is possible to reduce the
amount of water used.
When water pressure is less than 4L /min ,
ECO SHOWER RINSE is replaced with Normal RINSE.
To check whether Normal RINSE is set, press COURSE key
for 3 seconds. Incase Normal RINSE is set,
RINSE LED indicator blinks rapidly.
DRAIN SPIN SPIN RINSE
WATER
SUPPLY
SHOWER
ECO SHOWER RINSE Normal RINSE
WASH RINSE SPIN
นางงัลพัยหะรปบบแดาอะสำ้นงา้ล
วหะรนใำ้น้ชใรากณามะรปดัยหะรปยว่ชะจนางงัลพดัยหะรปบบแำ้นงา้ลราก ิตกปำ้นงา้ลรากา่วกาม้ดไามปไนุมหงงัลำกงัถ่ีทงา่
กัซ งา้ล น่ัป
น่ัป น่ัปำ้นยาบะร ำ้นงา้ล งา้ล
ำ้นณามิรป
ิตกปดาอะสำ้นงา้ล
นางงัลพดัยหะรปบบแดาอะสำ้นงา้ล
)ีทาน/L4า่วกยอ้นำ้น้ชใงอ้ตะจ(อพงยีพเ่มไำ้นนัดงรแอ่ืมเ ิตกปบบแำ้นงา้ลรากนทแดทะจนางงัลพดัยหะรปบบแำ้นงา้ลราก
The filter net is very easily blocked when it is used for long priod. Clean it in thefollowingway.
3. Confirm
if the top
cover is
closed.
การตรวจสอบ การตั้งค่าการล้างน้ำปกติ ให้กดปุ่ม"COURSE"
เป็นเวลา 3 วินาที ในกรณีที่การตั้งค่าล้างน้ำปกติ ตั้งไว้
ไฟ LED RINSE กระพริบอย่างรวดเร็ว

9
FRAGRANCE
1. Press POWER
ON/OFF key.
2. Press COURSE key,
and select the necessary
course.
3. Press FRAGRANCE
key, and turns on the
light.
CHILD LOCK
AUTO CLEAN
4. Press START/
PAUSE key.
Additional operating procedure
(If you want to cancel, hold down this key for 3 seconds again)
12
1. Press
POWER ON/OFF key. 2. Press COURSE key, and select
NORMAL course. 3. Press START/PAUSE key.
Instruction on washing courses
4. The machine generates a beep and turns off when it finishes the course.
1. Press
POWER ON/OFF key.
4. The machine generates a beep and turns off when it finishes the course.
3. Press START/PAUSE key.
2. Press AIR DRY key, and put
the light on it.
AIR DRY
Display represents drying time:
30min → 60min → 90min → 0
Caution
Automatic sensing function
If you select water level as desired in the normal course, the automatic sensing
function does not work.
When the power supply is “ON” status, hold down
“FRAGRANCE” key for 3 seconds.
After generating a beep, “L” is displayed for 3 seconds,
and the machine is locked.
When the power supply is “ON” status, hold down
“WATER LEVEL” key for 3 seconds.
After generating a beep, “C” is displayed for 3 seconds, and
cleaning the washing/spin drying tub is set on the machine.
(This course adds a cleaning process at the end of spinning,
and prevents secondary contamination in the tub)
This washing machine selects the appropriate water level and the operation time
automatically with the sensing function. In the case of operating
the automatic sensing function, there should be no water left in the tub.
The automatic sensing function does not work when you select the water level
manually, or when you select the courses : DELICATE, BLANKET, TUB CLEAN
เครื่องซักผ้านี้มีระบบปรับระดับน้ำอัตโนมัติ ให้เหมาะกับระยะเวลาในการทำงานที่เหมาะสม
ฟังก์ชั่นอัตโนมัติไม่ควรมีน้ำหลงเหลืออยู่ในถังซัก
ฟังก์ชั่นอัตโนมัติจะไม่ทำงานเมื่อคุณเลือกระดับน้ำ
ด้วยตนเองหรือเมื่อมีการเลือกโปรแกรม: ซักผ้าเนื้อบาง,ซักผ้าห่ม,โปรแกรมล้างถังซัก

1. Press
POWER
ON/OFF key.
2. Press COURSE key,
and select the necessary
course.
3. Press RESERVE key,
and set the time as desired.
4. Press
START/
PAUSE key.
Display represents reservation
time: 1hr → 24hrs.
1. Press
POWER ON/OFF key.
2. Press SOAK key, and set
the soaking time as desired.
3. Press
START / PAUSE key.
7. The machine generates a beep and turns off when it finishes the course.
6. The time setting counts down to show the remaining time.
4. The machine generates a beep and turns off when it finishes the course.
5. Start the reservation program.
Display represents soaking time
(11 steps):
5min → 10min → 20min → 40min
→ 60min → 2hrs → 3hrs → 4hrs
→ 8hrs → 12hrs→ 24hrs
Additional operating procedure
11
10
2
3
Put the clothes in the tub,
and press Power ON/OFF key.
Before starting of rinsing, please select [ Water level ].
Select the course as necessary .
Put in detergent as necessary,and close the top cover properly.
Only spinning
Only draining
Self-decided washing course
Only spinning etc.
Select the necessary processes.
In the cases below
Press START/PAUSE key.
1
Only rinsing and spinning
Ex.
RESERVE
SOAK
(In these cases, please keep the top cover close.)
Reuse of wash water
(There is wash water left in the tub)
(ในกรณีเหล่านี้โปรดปิดฝาเครื่องซักผ้า)