Sherwin-Williams GTS-ProCart 283-584 User manual

7930A
Related Manuals
HVLP T urbine Sprayers 824–170. . . . . . . . . . . . .
GTS–960 Bleeder Gun 308–336. . . . . . . . . . . . . .
GTS–980 Non–Bleeder Gun 308–810. . . . . . . . .
OWNER’S
MANUAL
824–171
Rev A
HVLP Compressor/Cart
120 V AC 50/60 Hz: Series
Maximum Working Pressure:
15 psi (1.0 bar, 104 kPa)
Model GTS–ProCart, Series A
Cart with material hose, 283–584
Cart with air & material hoses, 283–585
Cart with air & material hoses,
and GTS 980 Pressure Gun w/#3 fluid set, 232–576
The SHERWIN–WILLIAMS COMPANY, CLEVELAND, OHIO 44115
COPYRIGHT 1998, GRACO INC.
This manual contains important
warnings and information.
READ AND RETAIN FOR REFERENCE

  
Table of Contents
Warnings 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Information 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setup 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Shutdown 12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maintenance 13 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Specifications 19 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Warranty 20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Symbols
Warning Symbol
WARNING
This symbol alerts you to the possibility of serious
injury or death if you do not follow the instructions.
Caution Symbol
CAUTION
This symbol alerts you to the possibility of damage to
or destruction of equipment if you do not follow the
instructions.
WARNING
FIRE AND EXPLOSION HAZARD
Improper grounding, poor ventilation, open flames or sparks can cause a hazardous condition and
result in a fire or explosion and serious injury
.
D Ground the equipment and the object being sprayed. Refer to Grounding on page 7.
D If there is any static sparking or you feel an electric shock while using this equipment, stop spray-
ing immediately . Do not use the equipment until you identify and correct the problem.
D Provide fresh air ventilation to avoid the buildup of flammable fumes from solvents or the fluid
being sprayed.
D When flammable liquid is sprayed or used for flushing or cleaning the equipment, the compressor
must be placed at least 20 feet (6.1 m) away from areas where hazardous concentrations of flam -
mable vapors are likely to occur .
D
Use additional air hose if necessary to ensure that the compressor is operated in a clean, dry , well
ventilated area.
D Never place the compressor inside a spray booth! Use this equipment outdoors or in extremely well
ventilated areas.
D Keep the spray area free of debris, including solvent, rags, and gasoline.
D Electrically disconnect all equipment in the spray area.
D Extinguish all open flames or pilot lights in the spray area.
D Do not smoke in the spray area.
D Do not turn on or of f any light switch in the spray area while operating or if fumes are present.
D Do not operate a gasoline engine in the spray area.

824-1713
WARNING
INSTRUCTIONS
EQUIPMENT MISUSE HAZARD
Equipment misuse can cause the equipment to rupture or malfunction and result in serious injury .
D This equipment is for professional use only .
D
Read all instruction manuals, tags, and labels before operating the equipment.
D Use the equipment only for its intended purpose. If you are not sure, call your Graco distributor .
D Do not alter or modify this equipment. Use only genuine Graco parts.
D Check equipment daily . Repair or replace worn or damaged parts immediately .
D
Do not exceed the maximum working pressure of the lowest rated system component. The Com -
pressor/Cart has a working pressure of 15 psi (1.0 bar , 104 kPa).
D Use fluids and solvents which are compatible with the equipment wetted parts. Refer to the Speci-
fications
on page 19 for this information.
D Do not use hoses to pull equipment.
D Route hoses away from traffic areas, sharp edges, moving parts, and hot surfaces. Do not expose
Graco hoses to temperatures above 82 _ C (180 _ F) or below –40 _ C (–40 _F).
DW
ear hearing protection when operating this equipment.
D Do not lift pressurized equipment.
D Comply with all applicable local, state, and national fire, electrical, and safety regulations.
D Do not point the gun at anyone or at any part of the body .
D
Do not put your hand or fingers over the gun fluid nozzle.
D Do not stop or deflect leaks with your hand, body , glove or rag.
D Do not “blow back” fluid; this is not an air spray system.
D Follow the Pressure Relief Procedure on page 12 if the fluid nozzle clogs and before cleaning,
checking or servicing the equipment.
DT ighten all fluid connections before operating the equipment.
D Check the hoses, tubes, and couplings daily . Replace worn or damaged parts immediately .

  
WARNING
TOXIC FLUID HAZARD
Hazardous fluid or toxic fumes can cause serious injury or death if splashed in the eyes or on the skin,
inhaled, or swallowed.
D Know the specific hazards of the fluid you are using.
D Store hazardous fluid in an approved container . Dispose of hazardous fluid according to all local,
state and national guidelines.
D Always wear protective eyewear , gloves, clothing and respirator as recommended by the fluid and
solvent manufacturer .
D
Do not use 1,1,1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or
fluids containing such solvents in the turbine spray system, which contains aluminum and/or galva -
nized-coated parts. Such use could result in a serious chemical reaction, with the possibility of
explosion, which could cause death, serious injury , and/or substantial property damage.


Information
HVLP Compressor/Cart Information
The GTS–ProCart HVLP Compressor/Cart when used
with a turbine sprayer and turbine spray gun can spray
most coatings or finishes currently being used for
automotive refinish, industrial, aerospace, marine,
wood, plastic and architectural applications.
The cart/compressor provides air pressure to a 2–1/2
gallon remote pressure pot or a 2 quart pressure pot.
Under pressure, fluid is propelled from the pot to
turbine spray gun.
See Fig. 1 for Component Identification and Function.
HVLP System Operation
The spray gun of the HVLP system utilizes inbound air
pressure from the cart/compressor and HVLP turbine
sprayer to produce a high quality paint finish. The
spray gun produces a cone of air that carries and
directs the paint from the gun to the surface. Over
-
spray is minimized. Application is easier since fewer
paint passes are required to obtain coverage. In -
creased system transfer ef ficiency reduces material
requirements and clean-up time. The system allows
compliance with clean air laws for reduced VOC (vola -
tile organic compounds) emissions.
Refer to the HVLP turbine sprayer manual 824–170 for
information on the operation and use of the HVLP
turbine sprayer . Refer to the turbine gun manuals,
308–336 or 308–810, for information on the operation
and use of the turbine spray gun.
Dif ferent configurations of, HVLP compressor/carts,
turbine sprayers, guns, and accessories are available
to meet specific application requirements.
Unpacking
Unpack the Graco cart/compressor from the shipping
carton and inspect for any possible shipping damage.
If necessary , call your distributor .
The contents of the GTS–ProCart includes:
D
Cart with compressor
D Material hose
D Air hose (models 283–585 and 283–586 only)
D GTS 980 spray gun (model 283–586 only)
D Instruction manual, 824–171.

  
Component Identification and Function
7930A
Fig. 1
E
C
B
G
D
A
F
H
I
J
A Remote Paint Pot Holder Provides space for 2 qt or 2–1/ gal paint pots
B Air Outlet Connection for compressor air supply to remote paint pots
CT urbine Latch Latch locks turbine sprayer in position on cart
D Hose Holder Provides storage space for sprayer hose, gun and accessories
E Cart Handle Compressor/cart handle. Handle folds flat for minimum storage space
FT urbine Sprayer Base Mount Provides lock–mount for turbine sprayer on cart
G ON/OFF Switch ON/OFF power switch for compressor motor
H Air and Material Hoses Hoses provide operating air and material to gun
I 2–1/2 Gallon Paint Pot Holds 2–1/2 gallons of application material
JT urbine Spray Gun Controls and applies material to be sprayed


Setup
Grounding
WARNING
Improper installation or alteration of the grounding
plug will result in a risk of electric shock, fire or
explosion that could cause serious injury or death.
120 V ac Systems
1. This equipment requires a 120 V ac, 60 Hz, 15A
circuit with a grounding receptacle. See Fig. 2.
Fig. 2
Grounding Prong
Grounded
Outlets
2. Do not alter the ground prong or use an adapter .
3.
A 12 A WG gauge, 50 ft extension cord may be
used with this equipment.
Prepare the Fluid
1. Always strain the fluid before spraying; this
includes color , reducer and hardeners if used.
2. When using a turbine spray system, you need to
use a slower drying reducer or thinner to compen -
sate for the faster drying time caused by the warm
air of the turbine. Do not over reduce.
NOTE: The performance of the turbine sprayer will
vary with viscosity of material used and hose length.
Keep hose length short to prevent pressure drop.
Paint Reduction – Automotive Type Finishes
Reduce and catalyze all paint to manufacturer ’ s speci -
fications. T o compensate for the faster drying time of
turbine systems, use a reducer one-step slower than
what is used for conventional air spray .
Paint Reduction – Industrial or Domestic Coatings
Reduce and catalyze all paint to manufacturer ’ s speci -
fications. If no reductions are given, first thoroughly
mix the fluid to be sprayed. Then gradually mix in the
proper reducer , testing the fluid until you have the
correct spraying consistency .
T o test the consistency: Remove the stir stick from the
thinned paint. When the paint stream running of
f the
stir stick breaks into droplets, the first few drops should
be about one second apart.
Setup/Use Options
The HVLP compressor/cart has a variety of user
options. See Fig. 3 for compressor/cart uses.
NOTES:
D
Refer to turbine manual 824–170 for information on
turbine setup and operation.
D Refer to turbine gun manuals: 308–336 or 308–810,
for information on turbine spray gun setup and
operation.

  
Setup
7933A
7932A
7931A
Fig. 3
1. Place turbine (1) on cart
Cart/Compressor with turbine sprayer
and 2–1/2 gallon remote paint pot
1. T urn knob to free handle
2. Fold handle down to store
1
1
T
O ST ORE HANDLE
T O LOCK AND CONNECT TURBINE AND CAR T
2
T
O CARR Y REMOTE P AINT POT
1. Place remote paint pot in cart
2. Move latch (2) right to lock
1
2. Hook up per instructions
A
3. Plug cart into turbine outlet (A)
4. Plug turbine into grounded outlet

7934A
Fig. 4
C
D
D
2-1/2 Gallon Remote Pressure Pot
2 Quart Remote Pressure Pot
F
J
J
A
G
G
G
C
A
B
L
E
Cup Setup for Spray Gun
E
ZZ
HH
Cup–Over Option
see manual
308–336 or
308–810
F
KK
Y
XX
Y
Y
Z
X

Setup
Connect Fluid and Air Supplies
1. Connect gun air supply hose (A) between turbine
air outlet (B) and gun air inlet (C). DO NOT use
wrench to tighten connections; hand–tighten only .
See Fig. 4.
2. For GTS–4900: the GTS–4900 turbine uses
quick–connector at outlet (B). A wrench is not
required for hose connection.
3. If using spray gun cup (D), connect cup to gun
fluid inlet (E).
4. If using accessory remote pressure pots (F),
connect fluid supply hose (G) between remote
pressure pot fluid outlet (H) and gun fluid inlet (E).
Connect pressure pot air hose (J) between pres -
sure pot air regulator inlet (K) and cart compressor
air outlet (L).
NOTES:
D
The HVLP Cart/Compressor provides the air supply
for remote pressure pots.
D The circled letters in Fig. 4 indicate hose line con -
nections.
Connect to Electric Power
1. Plug compressor/cart power cord into turbine
auxiliary outlet (A) or grounded outlet. See Fig. 3.
2. If extension cord is used, it must be 3-wire, 12
A WG and 100 ft or less in length.

10  824-171
Setup
Fill the Cup or Remote Pressure Pot
Spray Gun Cup
WARNING
The spray gun cup is pressurized by the gun’ s air
supply. T o reduce the risk of serious injury from
pressurized fluid or accidental spray from the gun,
always turn of f the air supply to the gun before
removing the spray gun cup.
Only fill the cup 3/4 full to help keep the air pressure
tube clean, then install the cover
. The under-cup cover
has a latch (H) to secure it to the cup. The over-cup
has a ring with notches (J) that secures the cup hood
into place when locked in place on the cup.
Fig. 5 
H
J

Accessory Remote Pressure Pot
WARNING
The accessory remote pressure pots remain pres -
surized until pressure is manually relieved. T o
reduce the risk of serious injury from pressurized
fluid or accidental spray from the gun, always
relieve pressure in the pressure pot before loosen -
ing or removing the cover .
1. Relieve remote pressure pot pressure as follows:
a. T urn of f air supply to pressure pot. See Fig. 6.
b. 2 1/2 Gallon Remote Pot: Pull pressure relief
valve ring (206c) until pressure is completely
relieved.
2 Quart Remote Pot: Turn out pressure relief
knob (1
13) one turn. W ait until pressure is
completely relieved before removing cover .
Close knob.
Fig. 6
206c

113

2 quart
2 1/2 gallon
2. Remove pressure pot cover and fill. Secure cover .
NOTE: 2 quart remote pressure pot only: lightly coat
the cover threads with petroleum jelly .
CAUTION
If the 2 quart remote pressure pot is accidentally
tipped over or held at too great of an angle, fluid may
leak into the air regulator and cause damage. T ake
precautions to avoid this. If fluid does get into the
regulator , clean it immediately .
CAUTION
Do not tighten the pressure pot cover more than
hand-tight. Excessive tightening may damage the
cover gasket.


Setup
Prepare the Surface to be Sprayed
To achieve proper adhesion, make sure the surface to
be sprayed is completely clean.
Operating the Compressor
WARNING
Sparking can be expected in the normal operation
of the motor . Sparks could ignite fumes from
flammable liquid, dust particles and other flamma -
ble substances in the spray area, and cause seri -
ous injury and property damage. Be sure to follow
the precautions below:
D When flammable liquid is sprayed or used for
flushing or cleaning equipment, the compressor
must be placed at least 20 feet (6.1 m) away
from areas where hazardous concentrations of
flammable vapors are likely to occur .
D
Use additional air hose if necessary to ensure
that the compressor is operated in a clean, dry ,
well ventilated area.
D Never place the compressor inside a spray
booth! Use this equipment outdoors or in
extremely well ventilated areas.
DA void all ignition sources such as static electric -
ity from plastic drop cloths, open flames such as
pilot lights, hot objects such as cigarettes, arcs
from connecting or disconnecting power cords
or turning light switches on and of f. Extinguish
or remove all sources of ignition.
1. T urn the compressor on a few minutes before you
start spraying to allow for warm-up time.
NOTE: When the compressor is not in use for an
extended period of time, turn it of f. The compressor
does not shut of f automatically .
2.
Be sure the compressor filter is clean before
operating. See page 13 to check and clean the
filter.
NOTE: T o adjust the spray gun pattern, see the
turbine gun manual 308–336.
HVLP Compressor/Cart Cold W eather Operation
The HVLP compressor/cart uses a diaphragm com -
pressor
. When new , the diaphragm may becomes stif f
in cold weather . If cold enough, the diaphragm will not
allow the compressor motor to start (the unit will hum).
If this occurs, follow these steps:
1. T urn turbine and compressor OFF .
2.
Unplug turbine from power source.
3. Remove filter . Clean or replace if dirty .
4.
Spin cooling fan on compressor for a few revolu -
tions.
5.
Reassemble filter .
6.
Plug in turbine.
7. T urn turbine and compressor ON. If necessary ,
repeat procedure.

  
Shutdown
Pressure Relief Procedure
WARNING
PRESSURIZED EQUIPMENT HAZARD
The equipment stays pressurized until pressure is
manually relieved. To reduce the risk of a serious
injury from pressurized fluid, accidental spray from
the gun, or splashing fluid, follow the Pressure Re -
lief Procedure whenever you:
D are instructed to relieve the pressure,
D stop spraying,
D check or service any of the system equipment,
D or install or clean the fluid nozzles.
1. When spraying is finished, turn of f air supply to
gun.
2. T
urn of f turbine sprayer .
WARNING
The turbine hose outlet may be hot. Carefully
check the hose end before removing the hose.
3. If using remote pressure pot, relieve pressure by
following these steps:
a. T urn of f air supply to pressure pot.
b. 2 1/2 Gallon Remote Pot: Pull pressure relief
valve ring (206c) until pressure is completely
relieved.
2 Quart Remote Pot: Turn out pressure relief
knob (1
13) about one turn. W ait until pressure
is completely relieved before removing cover
.
Close knob. See Fig. 7.
Fig. 7
206c

113

2 1/2 gallon
2 quart
NOTE: Elevate spray gun and pull trigger . This will
allow fluid in fluid hose to drain back into remote
pressure pot.
4. If using a spray gun cup, unlatch cup cover and
loosen or remove cup from cover to relieve cup
pressure.
5.
Clean spray gun and cup as instructed in turbine
gun manual 308–336 or 308–810.

824-17113
Maintenance
Daily
Check the cart daily for cleanliness.
The compressor system is lifetime lubricated. The only
maintenance required is filter cleaning and replace -
ment.
The compressor filter must be clean at all times to
provide sufficient air flow to cool the motor and pres -
surized air to remote pressure pots. Check the filter
daily . Clean or replace as necessary .
T
o service the compressor filter:
1. T urn of f and unplug compressor .
2.
Pinch filter (A) and remove by hand. See Fig. 8.
3. Clean or replace filter as follows:
D Brush accumulated paint and dirt from surface
of foam filter .
D
Rinse filter in water with mild detergent. Blow
dry.
D Replace filter if paint is caked–on.
WARNING
T o avoid damage to the compressor and possible
electric shock, never install a damp filter in the
compressor.
CAUTION
Dust and dirt can accumulate during use causing
equipment damage. Do not operate the compressor
without the filter installed.
Fig. 8
A
7935A
Weekly
Check hoses for cracks, leaks, and holes. Replace, as
necessary.

  
Troubleshooting
PROBLEM CAUSE SOLUTION
No fluid delivery .No material, no remote container pres-
surization,
hose or pickup tube clogged.
Check container for material.
Check for leaks at the container gasket,
2 quart lid, and 2 1/2 gal pot wing nuts.
Tighten
wing nuts.
Check for air flow from male quick–dis-
connect at compressor outlet (approx.
1/4 CFM).
Turn pressure regulator clockwise. Look
for pressure on gauge. (If no pressure on
gauge, check air line and fittings).
Check hole in tank lid under regulator or
needle valve 2 Qt lid. Clean if necessary .
Check for obstructions or kinks in hoses
and fittings.
Check if fluid pickup tube is unplugged.
Tighten.
Blow out and clear material hose.
Compressor fails to start Cold weather operation. See Cold W eather Operation instruc-
tions,
page 1 1.


Repair
WARNING
Turn of f turbine and unplug power for the following
procedures.
Compressor/Cart Switch Replacement
1. T o remove compressor power switch (28), wedge
large flat blade screwdriver between top of switch
and cart face plate. See Fig. 9, Fig. 10, and Parts
on page 16.
2. Push down firmly on switch. Pry switch out far
enough so two top switch locking tabs (A) are
visible.
3.
While maintaining outward pressure on switch,
push down on two locking tabs with small flat
blade screwdriver until they release. Switch will
pop out.
4. Disconnect two wires and remove switch.
5. Reinstall by connecting wires to new switch. Snap
switch into place.
Fig. 9
A
28
7936A
Compressor Replacement
1. Remove four cart grill plate screws (23). Remove
cart filter (9) and compressor duct (10). Clean or
replace filter as necessary. See Fig. 10, Fig. 1 1,
and Parts on page 16.
2. Remove air hose (12) from compressor .
3.
Remove screws (1 1) attaching compressor .
4.
Disconnect motor wires and remove compressor .
5.
Install new compressor and connect motor wires.
6. Reinstall hose on compressor .
7.
Reinstall compressor duct and cart filter .
7930A
Fig. 10
9,23
28
Fig. 11
Power
Cord
Rocker
Switch
Motor
Compressor wiring
Power Cord Replacement
1. Remove four cart grill plate screws (23) and re -
move cart filter (9). (Clean or replace filter as
necessary). See Fig. 10 and Parts on page 16.
2. Replace power cord (29).
3. Reinstall cart filter .

  
Parts
29
2
7
3
6
5
4
9
10
19
1
25
24
26
28
8
11
12
13
13
15
18
21
22
23
7
20
1a
1c
1b
1d
27


Parts
Ref
No. Part No. Description Qty
1 240–008
HOUSING ASSY , cart 1
1a 191–824
. W ASHER, space 2
1b 113–658
. NUT , crest, hat 2
1c 113–647
. WHEEL 2
1d 111–841
. W ASHER, plain, 5/8 in. 2
2 240–000
HANDLE, cart 1
3 114–047 VAL
VE, check 1
4 178–945 NUT
, hex 1
5 M70–809
FITTING, barbed 1
6* 114–281
COMPRESSOR, 1 10 V 1
7 105–328 SCREW
, cap, hx hd 4
8 192–798 PLA
TE, handle 2
9† 192–794 FIL
TER, cart 1
10 192–795 DUCT
, compressor 1
11* 112–948 SCREW
, machine, pan hd 3
12 192–810
HOSE, air , cart 1
13 M71–635 CLAMP
, hose 2
15 193–083 SP
ACER, foot 1
18 114–270 KNOB 2
* Part of replacement compressor . Order P/N 240–277.
† Cart filters are available in 3 packs. Order P/N 240–274.
Ref
No. Part No. Description Qty
19 192–800 RET
AINER, handle 2
20 107–557 SCREW
, cap, hex hd 1
21 192–802 SP
ACER, handle 2
22 192–797 PLA
TE, grill, cart 1
23 106–084 SCREW
, mach, pan hd 4
24 114–421 CONNECT
OR, cord strain relief 1
25 192–799
HANDLE, latch 1
26 192–801 SCREW
, shoulder 1
27* 107–262
TERMINAL, insulated, female 2
28 114–293
SWITCH, rocker , red 1
29 114–298
CORD SET , 24 in. 1
36 M70–604 T
ANK, paint, 2.5 gal. (not shown) 1
37 240–075
HOSE, air , quick disconnect,
1/4 in. x 24 in. (not shown) 1
38 240–481
HOSE, material, black, 3/8 in. x
30 ft (not shown) 1
39 240–299
HOSE, turbine air , gray , 30 ft (not
shown) (supplied with 232–575 and
232–576) 1
40 240–294
GUN, GTS 980P with #3 fluid set
(not shown) (supplied with
232–576) 1

  
Notes


Specifications
Power Requirements 120 V ac, 50/60 Hz, 12 Amps . . .
Power Cord No. 14 A WG, 3 wire, 1 ft (0.3 m) {. . . . . . .
CFM unrestricted 0.4 cfm . . . . . . . . . . . . . . . . . . . . . . . . . .
HP 1/16 HP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PSI 15 psi (1.0 bar , 104 kPa) . . . . . . . . . . . . . . . . . . . . . . .
Maximum Compressor Hose Length 60 ft (18 m). . . . .
Wetted Parts
Bare Spray Gun Stainless Steel, Brass, r,. .
Hard-coated Aluminum
Spray Gun Cups Aluminum, Polyethylene . . . . . . . .
2 Quart Accessory Remote
Pressure Pot Aluminum, Brass, . . . . . . . . . . . . . . . .
Polyethylene
2-1/2 Gallon Accessory Remote
Pressure Pot Steel with . . . . . . . . . . . . . . . . . . . . . . .
solvent–resistant finish, EPDM Gasket (standard)
Cart/Compressor Shipping W eight (w/o pkg., hose,
or gun) 22 lb (10 kg) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sound level per ISO 3744
Sound power 74.0 dB(A) . . . . . . . . . . . . . . . . . . . . . . . . .
Sound pressure 70.0 dB(A) . . . . . . . . . . . . . . . . . . . . . .
{ Extension cord must be 3-wire, 12 A WG; 100 ft or shorter .
Loctite
r is a registered trademark of the Loctite Corporation.
PTFE
PTFE

20  824-171
Sherwin-Williams Standard W arranty
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from
defects
in material and workmanship on the date of sale by an authorized Graco distributor to the original purchaser for use. With the
exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of
sale, repair or replace any part of the equipment determined by Graco to be defective. This warranty applies only when the equipment
is installed, operated and maintained in accordance with Graco’ s written recommendations.
This warranty does not cover , and Graco shall not be liable for general wear and tear , or any malfunction, damage or wear caused by
faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or sub -
stitution of non–Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of
Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture,
installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for
verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The
equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect
in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor , and
transportation.
THIS
W ARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER W ARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT
NOT LIMITED T O WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s
sole obligation and buyer ’ s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other
remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property , or any
other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the
date of sale.
GRACO MAKES NO W ARRANTY , AND DISCLAIMS ALL IMPLIED W ARRANTIES OF MERCHANT ABILITY AND FITNESS FOR
A PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD
BUT
NOT MANUF ACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches,
hose, etc.), are subject to the warranty , if any , of their manufacturer . Graco will provide purchaser with reasonable assistance in mak -
ing
any claim for breach of these warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment
hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract,
breach of warranty , the negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings
entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnais -
sent
avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires
exécutés, donnés ou intentés à la suite de ou en rapport, directement ou indirectement, avec les procedures concernées.
ADDITIONAL W ARRANTY COVERAGE
Graco does provide extended warranty and wear warranty for products described in the “Graco Contractor Equipment W arranty
Program”.
Phone Number
TO PLACE AN ORDER , contact your Graco distributor , or call this number to identify the distributor closest to you:
1–800–367–4023 T
oll Free
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
The SHER WIN–WILLIAMS COMPANY , 101 PROSPECT AVENUE, CLEVELAND, OHIO 441 15
PRINTED IN U.S.A. 824–171 January 1998