Doosan XXHP1270FCAT User manual

Doosan Infracore Portable Power
1293 Glenway Drive
Statesville, N.C. 28625
www.doosanportablepower.com
Book: 46499257 (4-27-2010) Rev A
This manual contains important safety information.
Do not destroy this manual.
This manual must be available to the personnel who operate and maintain this machine.
OPERATION and MAINTENANCE
COMPRESSOR MODEL
XXHP1270/XHP1500FCAT-T3 (D58)
MANUAL
Revised (10-12)
Doosan purchased Bobcat Company from Ingersoll-Rand Company in
2007. Any reference to Ingersoll-Rand Company or use of trademarks,
service marks, logos, or other proprietary identifying marks belonging
to Ingersoll-Rand Company in this manual is historical or nominative
in nature, and is not meant to suggest a current affiliation between
Ingersoll-Rand Company and Doosan Company or the products of
either.

2

3
TABLE OF CONTENTS
Operating & Maintenance Manual
TITLE PAGE
FOREWORD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Compressed Air . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Radiator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Transport. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Decals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
GENERAL DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
OPERATING INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Operating Controls and Instruments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Lifting Unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Setting Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Compressor Mounting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Before Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Normal Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Stopping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Air Aftercooler System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Aftercooler Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Low Ambient Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Daily Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Weekly Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Pressure Regulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Butterfly Valve (BFV) Linkage Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Start Pressure Adjustment:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Low Pressure Regulator Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
High Pressure Regulator Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Engine Overspeed Air Shutoff System Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Optional Engine Overspeed Shutdown with Engine Air Inlet Shutoff . . . . . . . . . . . . . . . . . . . . . . . .40
Operation of the Air Inlet Shutoff Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

4
TABLE OF CONTENTS
Operating & Maintenance Manual
TITLE PAGE
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Maintenance Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Maintenance Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Protective Shutdown System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Scavenge Line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Oil Temperature Control Valve (OTCV) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Compressor Oil Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
Compressor Oil Separator Element . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
Compressor Oil Cooler, Engine Radiator, and other Heat Exchangers . . . . . . . . . . . . . . . . . . . . . . . . .53
Air Filter Element. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
Cooling Fan Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Fan Belt Tension - Check and Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Fuel System (if applicable) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Fuel Filter Water Separator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Charge Air Cooler Pipework . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
Hoses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
Electrical System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
Battery (if applicable) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
Pressure System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
Lubrication. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
Engine Lubricating Oil. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
Compressor Lubricating Oil. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
LUBRICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
Compressor Oil Change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
Portable Compressor Fluid Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
Compressor Diagnostic Display Codes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
Troubleshooting Chart. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
ELECTRICAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
General Information and Operational Theory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
Wedge Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
Temperature Sensors and Pressure Transducers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
Controller Outputs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
Digital Inputs and Outputs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
Pressure Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
Electronic Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
Oil Temperature Controller (OTC). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
Electrical System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80
Trouble Shooting Flow Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81

5
TABLE OF CONTENTS
Operating & Maintenance Manual
TITLE PAGE
SCHEMATICS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Harness System Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84
Wedge to Engine Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
J1939 CAN BUSS Communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86
System Wiring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87

6

Book: 46499257 (4-27-2010) Rev A 7
Foreword

Operating & Maintenance Manual Foreword
8Book: 46499257 (4-27-2010) Rev A
Foreword
The contents of this manual are considered to be proprietary and confidential to Doosan
Infracore Portable Power (herein referred to as “Portable Power”), and should not be
reproduced without the prior written permission of Portable Power.
Nothing contained in this document is intended to extend any promise, warranty or
representation, expressed or implied, regarding the Portable Power products described
herein. Any such warranties or other terms and conditions of sale of products shall be in
accordance with the standard terms and conditions of sale for such products, which are
available upon request.
This manual contains instructions and technical data to cover all routine operation and
scheduled maintenance tasks by operation and maintenance staff. Major overhauls are
outside the scope of this manual and should be referred to an authorized Portable Power
Service department.
All components, accessories, pipes and connectors added to the compressed air system
should be:
• of good quality, procured from a reputable manufacturer and, wherever possible, be
of a type approved by Portable Power.
• clearly rated for a pressureat least equal to the machinemaximum allowable working
pressure.
• compatible with the compressor lubricant/coolant.
• accompanied with instructions for safe installation, operation and maintenance.
Details of approved equipment are available from the Portable Power Service departments.
The use of repair parts other than those included within the approved parts list may create
hazardous conditions over which Portable Power has no control. Therefore, Portable Power
cannot be held responsible for equipment in which non-approved repair parts are installed.
Portable Power reserves the right to make changes and improvements to products without
notice and without incurring any obligation to make such changes or add such improvements
to products sold previously.
The intended uses of this machine are outlined below and examples of unapproved usage are
also given. However, Portable Power cannot anticipate every application or work situation that
may arise. If in doubt, consult supervision.
This machine has been designed and supplied for above ground operation to be used for
compression of normal ambient air containing no additional gases, vapors or particles within
the ambient temperature range specified in the general data section of this manual.

Foreword Operating & Maintenance Manual
Book: 46499257 (4-27-2010) Rev A 9
This machine should not be used:
• For direct or indirect human consumption of the compressed air.
• Outside the ambient temperature range specified in the general data section of this
manual.
• When an actual or foreseeable riskof hazardous levels of flammablegases or vapors
exists.
• With other than Portable Power approved components.
• With guards, or controls or switches missing or disabled.
• For storage or transportation of materials inside or on the enclosure.
This company accepts no responsibility for errors in translation of this manual from the original
English version.
You as the customer are expected to provide certain service and maintenance items. Your
Portable Power dealer will provide all other more detailed service and maintenance items on
a special preventive maintenance schedule for each machine. It is very important that the
minimum service and maintenance requirements explained in this manual be performed at the
required intervals. Exceeding these intervals may reduce the reliability of the machine.
The purpose of this manual is to train the operator with functions, operation, and basic service
and maintenance requirements of the compressor. During the preparation of this manual,
every effort was made to ensure the adequacy and accuracy of the contents.
Your Portable Power dealer will assist with setup and initial startup of the compressor. He will
also provide brief operating and service instructions and will insure that a copy of this manual
is included with the machine. Before starting the compressor, this manual and instructions
should be carefully read to obtain a thorough knowledge of the duties to be performed. Please
take pride in the compressor, keep it clean, and in good mechanical condition.

Operating & Maintenance Manual Foreword
10 Book: 46499257 (4-27-2010) Rev A

Book: 46499257 (4-27-2010) Rev A 11
Safety

Operating & Maintenance Manual Safety
12 Book: 46499257 (4-27-2010) Rev A
Safety
General Information
Never operate unit without first observing all safety warnings and carefully reading the
operation and maintenance manual shipped from the factory with this machine.
Ensure that the operator reads and understands the decals and consults the manuals before
maintenance or operation.
Ensure that maintenance personnel are adequately trained, competent and have read the
maintenance manuals.
Make sure that all protective covers are in place and that the canopy/doors are closed during
operation.
The specification of this machine is such that the machine is not suitable for use in flammable
gas risk areas. If such an application is required then all local regulations, codes of practice
andsite rulesmust beobserved.Toensurethat themachinecan operateinasafeandreliable
manner, additional equipment such as gas detection, exhaust spark arrestors, and intake
(shut-off) valves may be required, dependent on local regulations or the degree of risk
involved.
A weekly visual check must be made on all fasteners/fixing screws securing mechanical parts.
In particular, safety-related parts such as lifting bail should be checked for total security.
All components which are loose, damaged or unserviceable, must be rectified without delay.
Air discharged from this machine may contain carbon monoxide or other contaminants which
will cause serious injury or death. Do not breathe this air.
This machine produces loud noise. Extended exposure to loud noise can cause hearing loss.
Always wear hearing protection when operating this unit.
Never inspect or service unit without first disconnecting battery cable(s) to prevent accidental
starting.
Do not use petroleum products (solvents or fuels) under high pressure as this can penetrate
the skin and result in seriousillness. Wear eye protection while cleaning unit with compressed
air to prevent debris from injuring eye(s).
Rotating fan blade can cause serious injury. Do not operate without guard in place.
Use care to avoid contacting hot surfaces (engine exhaust manifold and piping, air receiver
and air discharge piping, etc.).
Ether is an extremely volatile, highly inflammable gas. When it is specified as a starting aid,
use sparingly. DO NOT USE ETHER IF THE MACHINE HAS GLOW PLUGS OR INLET
HEATER STARTING AIDS OR ENGINE DAMAGE WILL RESULT.
Never operate unit with guards, covers or screens removed. Keep hands, hair, clothing, tools,
blow gun tips, etc. well away from moving parts.

Safety Operating & Maintenance Manual
Book: 46499257 (4-27-2010) Rev A 13
Compressed Air
Compressed air can be dangerous if incorrectly handled. Before doing any work on the unit,
ensure that all pressure is vented from the system and that the machine cannot be started
accidentally.
Ensure that the machine is operating at the rated pressure and that the rated pressure is
known to all relevant personnel.
All air pressure equipment installed in or connected to the machine must have safe working
pressure ratings of at least the machine safety valve setting.
If more than one compressor is connected to one common downstream plant, effective check
valves and isolation valves must be fitted and controlled by work procedures, so that one
machine cannot accidentally be pressurized or over pressurized by another.
Compressed air must not be used for adirect feed to any form of breathing apparatusor mask.
High Pressure Air can cause serious injury or death. Relieve pressure before removing filler
plugs/caps, fittings or covers.
Airpressure canremain trappedinan airsupply linewhich canresultinseriousinjuryordeath.
Always carefully vent air supply line at tool or vent valve before performing any service.
The discharged air contains a very small percentage of compressor lubricating oil and care
should be taken to ensure that downstream equipment is compatible.
If the discharged air is to be ultimately released into a confined space, adequate ventilation
must be provided.
When using compressed air, always use appropriate personal protective equipment.
All pressure containing parts, especially flexible hoses and their couplings, must be regularly
inspected, be free from defects and be replaced according to the manual instructions.
Avoid bodily contact with compressed air.
The safety valve located in the separator tank must be checked periodically for correct
operation.
Whenever the machine is stopped,air will flow back into the compressor system from devices
orsystemsdownstreamof themachineunless theservicevalve isclosed.Install acheckvalve
at the machine service valve to prevent reverse flow in the event of an unexpected shutdown
when the service valve is open.

Operating & Maintenance Manual Safety
14 Book: 46499257 (4-27-2010) Rev A
WARNING
!
Unrestricted air flow from a hose will result in a whipping motion of the
hose which can cause serious injury or death.
Safety devices such as hose restraints (whipchecks) must be used to prevent hose whipping
if a connection fails. Whipchecks are to be constructed of woven stainless steel, galvanized
steel wire rope or chain with a minimum strength of 17,000 pounds (75.4 kN) for 3” hose
operating at 500 psi. Whipchecks must be fastened to suitable mounting points or shackles.
Refer to the OperatingInstructions Section in this manualunder WARNING for unrestricted air
flow from a hose for more detail.
The mounts and/or shackles are to be of the same or greater strength as the whipchecks. An
engineer should be consulted about suitability of whipchecks, mounts, mounting points,
shackles and fittings as well as strength rating of materials. Whipchecks must be used at the
hose origination, termination and each hose to hose connection.
Hoses can fail in areas other than at connecting points and require daily inspection of the
hoses for:
• Cuts, cracks or kinks
• Weaken clamps due to rust and corrosion
• Damaged connections
• Deformity
• Incorrect or incompatible components or fittings
• Any visual damage
Hoses must be selected that are rated for the application as to the maximum pressure and
temperatureto beencounteredas wellascompatiblewiththe materialsbeingconveyedinside
the hose. Hoses must be compatible with the compressor lubricant.
Never allow the unit to sit stopped with pressure in the receiver-separator system.
Materials
Engine exhaust fumes will be produced during the operation of this machine. Ensure that
adequate ventilation of the cooling system and exhaust gases is maintained at all times.
WARNING
!
Avoid inhalation of engine exhaust fumes.

Safety Operating & Maintenance Manual
Book: 46499257 (4-27-2010) Rev A 15
The following substances are used in the manufacture of this machine and may be hazardous
to health if used incorrectly:
• anti-freeze
• compressor lubricant
• engine lubricant
• preservative grease
• rust preventative
• diesel fuel
• battery electrolyte
WARNING
!
Avoid ingestion, skin contact and inhalation of fumes
Should compressor lubricant come into contact with the eyes, irrigate with water for at least 5
minutes.
Should compressor lubricant come into contact with the skin, wash off immediately. Consult a
physician if large amounts of compressor lubricant are ingested or if compressor lubricant is
inhaled. Never give fluids or induce vomiting if the patient is unconscious or having
convulsions.
Safetydatasheetsforcompressor andenginelubricantsshould beobtainedfromthe lubricant
supplier.
DoNOTstart oroperatethismachineinaconfinedarea. Avoid breathing exhaustfumes when
working on or near the machine.
This machine may include such materials as oil, diesel fuel, antifreeze, brake fluid, oil/air filters
and batteries which may require proper disposal when performing maintenance and service
tasks. Contact local authorities for proper disposal of these materials.
Battery
A battery contains sulfuric acid and can give off gases which are corrosive and potentially
explosive. Avoid contact with skin, eyes and clothing. In case of contact, flush area
immediately with water.

Operating & Maintenance Manual Safety
16 Book: 46499257 (4-27-2010) Rev A
WARNING
!
Do not attempt to slave start a frozen battery since this may cause it to
explode.
Exercise extreme caution when using booster battery. To jump battery, connect ends of one
booster cable to the positive (+) terminal of each battery. Connect one end of other cable to
the negative (-) terminal of the booster battery and other end to a ground connection away
from dead battery (to avoid a spark occurring near any explosive gases that may be present).
After starting unit, always disconnect cables in reverse order.
Radiator
Hot engine coolant and steam can cause injury. Ensure that the radiator filler cap is removed
with due care and attention.
Do not remove the pressure cap from a HOT radiator. Allow radiator to cool down before
removing pressure cap.
WARNING
!
Hot engine coolant and steam can cause injury. When adding coolant or
antifreeze solution to the engine radiator, stop the engine at least one
minute prior to releasing the radiator filler cap. Using a cloth to protect
the hand, slowly release the filler cap, absorbing any released fluid with
the cloth. Do not remove thefiller cap until all excess fluid is released and
the engine cooling system fully depressurized.
WARNING
!
Follow the instructions provided by the antifreeze supplier when adding
or draining the antifreeze solution. It is advisable to wear personal
protective equipment to prevent skin and eye contact with the antifreeze
solution.
Transport
Whenloading ortransportingmachinesensure that thespecifiedlifting and tie downpointsare
used.

Safety Operating & Maintenance Manual
Book: 46499257 (4-27-2010) Rev A 17
Decals
Decals are located on the machine to point out potential safety hazards. Read and
follow these instructions. If you do not understand the instructions, inform your
supervisor.
Note that there are different decal headings:
DANGER
!
(Red Background)
Indicates the presence of a hazard which WILL cause serious injury,
death or property damage, if ignored.
WARNING
!
(Orange Background)
Indicates the presence of a hazard whichCAN cause serious injury, death
or property damage, if ignored.
CAUTION
!
(Yellow Background)
Indicates the presence of a hazard which WILL or can cause injury or
property damage, if ignored.
NOTICE
(Blue Background)
Indicates important set-up, operating or maintenance information.

Operating & Maintenance Manual Safety
18 Book: 46499257 (4-27-2010) Rev A
FREE SAFETY DECALS
To promote communication of Safety Warnings on
products manufactured by the Portable Power Division in
Statesville, N.C. Safety Decals are available free of
charge. Safety decals are identified by the decal
heading: DANGER, WARNING or CAUTION. Decal part
numbers are on the bottom of each decal and are also
listed in the compressor’s parts manual. Submit orders
for Safety Decals to the Statesville Parts Service
Department. The no charge order should contain only
Safety Decals. Help promote product safety! Replace
decals that are not readable.

Book: 46499257 (4-27-2010) Rev A 19
General Data

Operating & Maintenance Manual General Data
20 Book: 46499257 (4-27-2010) Rev A
General Data
*Does not include skids or other attachments.
MODELS XXHP1270FCAT XHP1500FCAT
Air Delivery - cfm (litres/sec) 1270 (599) 1500 (708)
COMPRESSOR
Rated Operating Pressure - psi (kPa) 350-500 (2413-3448) 200-350 (1379-2413)
ENGINE (Diesel)
Manufacturer Caterpillar Caterpillar
Model C18 C18
Rated HP at 1850 rpm (kw) 700 (522) 700 (522)
Electrical System 24VDC 24VDC
Full Load Speed - rpm 1625 1850
No Load Speed - rpm 1350 1350
FLUID CAPACITIES - U.S. Gallons (litres)
Compressor Lubricant 85 (321) 85 (321)
Engine Lube (including filter) 11.0 (41.6) 11.0 (41.6)
Engine Coolant (radiator) 13.5 (51) 13.5 (51)
Fuel Tank (Clean DIESEL fuel) NA NA
AMBIENT TEMPERATURE RANGE
Ambient Temperature Range -20°F to 120°F (-29°C to 49°C)
UNITS MEASUREMENTS/WEIGHTS
Feet (Meters) LRG
Overall Length 15.34 (4.68)
Overall Height 7.42 (2.26)
Overall Width 7.42 (2.26)
Gross Weight* - pounds (kg) 16,123 (7313)
(including fluids - no fuel) 16,911 (7671)