Shop fox W1750 User manual

Introduction
Your new Model W1750 Bandsaw Stand (Figure 1) is
designed for use with the Model W1749 9" Bandsaw.
Inventory (Figure 2) Qty
A. Long Top Brackets .........................................2
B. Short Top Brackets ........................................2
C. Long Bottom Brackets ....................................2
D. Short Bottom Brackets ....................................2
E. Stand legs ...................................................4
Hardware Bag (Not Shown)
• Carriage Bolts 5⁄16"-18 x 1⁄2" ........................... 16
• Hex Bolts 5⁄16"-18 x 13⁄4" .................................4
• Hex Nuts 5⁄16"-18 ........................................ 20
• Flat Washers 5⁄16" ........................................ 24
Specifications
• Overall Size ............... 211⁄2" W x 273⁄4" L x 271⁄4" H
• Weight .................................................12 lbs
Assembly
We recommend assembling the stand upside down. To
make it easier, have an assistant hold the pieces while
you assemble the stand.
Model W1750
Bandsaw Stand
Instruction Sheet
NOTICE
Do not final tighten stand bolts until all components
have been assembled.
Figure 1. Model W1750.
Figure 2. Model W1750 Inventory.
Figure 3. Top and bottom long brackets
secured to a stand leg.
To assemble the stand, do these steps:
1. Mount a long top and bottom bracket to a stand leg
and loosely secure with two 5⁄16"-18 x 1⁄2" carriage
bolts, flat washers, and hex nuts as shown in Figure 3.
A
B
D
E
C
Leg
Long
Bottom
Bracket
Long Top
Bracket

-2-
W1750 Bandsaw Stand
Figure 4. A completed leg assembly.
Figure 6. Completed stand assembly.
Figure 5. Short top and bottom brackets
secured to a leg assembly.
2. Secure a second leg to the long top and bottom
brackets with two 5⁄16"-18 x 1⁄2" carriage bolts, flat
washers and hex nuts as shown in Figure 4.
3. Repeat Steps 1–2 to build another leg assembly.
4. Secure the short top and bottom brackets to one of
the leg assemblies as shown in Figure 5 with four
5⁄16"-18 x 1⁄2" carriage bolts, flat washers, and hex
nuts.
5. Fasten the stand assembly to the other leg assembly
and secure with the remaining fasteners (Figure 6).
6. Turn the stand upright and adjust it so the legs are
evenly positioned, then tighten all the stand fasten-
ers.
Mounting
To mount the stand to the bandsaw, do these steps:
1. Align the four holes on the bottom of the Model
W1749 with the corresponding holes on the Model
W1750 top.
2. Using two 12mm open-end wrenches, secure the
stand to the bandsaw with four 5⁄16"-18 x 13⁄4" hex
bolts, four hex nuts, and eight 5⁄16" flat washers as
shown in Figure 7.
Customer Service
For questions contact Woodstock International Technical
Support at [phone], or send e-mail to: tech-
[e-mail].
Figure 7. Mounting Model W1749 bandsaw
to W1750 stand (2 mounting holes shown).
Leg
Short Bottom Brackets
Short Top Brackets
Hex
Bolt
Flat
Washers
Hex
Nut

-3-
W1750 Bandsaw Stand
COPYRIGHT © MAY, 2006 BY WOODSTOCK INTERNATIONAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC. Printed in China#8198BL
REF PART # DESCRIPTION
1 X1750001 LEG
2 X1750002 LONG TOP BRACKET
3 X1750003 SHORT TOP BRACKET
4 X1750004 LONG BOTTOM BRACKET
5 X1750005 SHORT BOTTOM BRACKET
6 XPCB02 CARRIAGE BOLT 5/16-18 X 1/2
7 XPW07 FLAT WASHER 5/16
8 XPN02 HEX NUT 5/16-18
9 XPB22 HEX BOLT 5/16-18 X 1-3/4
10 X1750010 FOOT PAD 45MM









