Show Tec Wipe Out 360 RGBW User manual

Wipe Out 360 RGBW V1
V1
Highlite International B.V. –Vestastraat 2 –6468 EX –Kerkrade –the Netherlands
Ordercode: 42562
MANUAL
ENGLISH

1
Ordercode: 42562
Wipe Out 360 RGBW
Table of contents
Warning ...............................................................................................................................................................................2
Unpacking Instructions.................................................................................................................................................2
LED Expected Lifespan ................................................................................................................................................2
Safety Instructions .........................................................................................................................................................2
Operating Determinations ..........................................................................................................................................4
Rigging ............................................................................................................................................................................4
Connection with the mains.........................................................................................................................................5
Return Procedure..........................................................................................................................................................6
Claims..............................................................................................................................................................................6
Description of the device.................................................................................................................................................7
Overview ........................................................................................................................................................................7
Frontside..........................................................................................................................................................................8
Backside .........................................................................................................................................................................8
Installation...........................................................................................................................................................................9
Set Up and Operation .......................................................................................................................................................9
Control Modes...............................................................................................................................................................9
One Wipe Out (Auto and Manual) ........................................................................................................................9
One Wipe Out (Sound-controlled).........................................................................................................................9
Multiple Wipe Outs (Master/Slave control)...........................................................................................................9
Multiple Wipe Outs (DMX Control) .......................................................................................................................10
Fixture Linking...............................................................................................................................................................11
Data Cabling...............................................................................................................................................................11
Control Panel ...............................................................................................................................................................12
Control Mode ..............................................................................................................................................................12
DMX Addressing ..........................................................................................................................................................12
Menu Overview...........................................................................................................................................................13
Main Menu Options....................................................................................................................................................15
1. Manual Mode ......................................................................................................................................................15
1.1 Manual Mode - LED ..........................................................................................................................................15
1.2 Manual Mode - Pan..........................................................................................................................................16
1.3 Manual Mode - Tilt.............................................................................................................................................17
2. Built-in Program Mode ........................................................................................................................................17
3. Sound-controlled Mode. ....................................................................................................................................17
4. DMX-512 Mode ....................................................................................................................................................17
5. Master/Slave Mode.............................................................................................................................................17
6. Settings...................................................................................................................................................................18
6.1 Settings –BL Time ...............................................................................................................................................18
6.2 Settings –Adjust .................................................................................................................................................18
6.3 Settings –Reset ..................................................................................................................................................18
6.4 Settings –Power .................................................................................................................................................18
6.5 Settings –Error.....................................................................................................................................................18
6.6 Settings –Lamp ..................................................................................................................................................18
6.7 Settings –Use ......................................................................................................................................................18
6.8 Settings –Sensor.................................................................................................................................................19
6.9 Settings –About .................................................................................................................................................19
DMX Channels .............................................................................................................................................................20
1 channel ..................................................................................................................................................................20
22 channels...............................................................................................................................................................20
26 channels...............................................................................................................................................................21
Maintenance....................................................................................................................................................................24
Replacing the Fuse.....................................................................................................................................................24
Troubleshooting ...............................................................................................................................................................24
No Light.........................................................................................................................................................................24
No Response to DMX..................................................................................................................................................25
Product Specifications....................................................................................................................................................26
Dimensions........................................................................................................................................................................27
Notes ..................................................................................................................................................................................28

2
Ordercode: 42562
Wipe Out 360 RGBW
Warning
Unpacking Instructions
Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure
that all parts are present, and have been received in good condition. Notify the dealer immediately and
retain packing material for inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture must be
returned to the factory, it is important that the fixture be returned in the original factory box and packing.
Your shipment includes:
• Showtec Wipe Out 360 RGBW
• PowerCon to Schuko (1,5 m)
• 1 bracket and 3 quick-locks
• User manual
LED Expected Lifespan
LEDs gradually decline in brightness over time. HEAT is the dominant factor that leads to the acceleration
of this decline. Packaged in clusters, LEDs exhibit higher operating temperatures than in ideal or singular
optimum conditions. For this reason, when all color LEDs are used at their fullest intensity, life of the LEDs is
significantly reduced. If improving the lifespan is of higher priority, place care in providing for lower
operational temperatures. This may include climatic-environmental and the reduction of overall
projection intensity.
Safety Instructions
Every person involved with the installation, operation and maintenance of this device has to:
•be qualified
•follow the instructions of this manual

3
Ordercode: 42562
Wipe Out 360 RGBW
Before the initial start-up, please make sure that there is no damage caused by transportation.
Should there be any, consult your dealer and do not use the device.
To maintain perfect condition and to ensure a safe operation, it is absolutely necessary for the user to
follow the safety instructions and warning notes contained in this manual.
Please consider that damages caused by manual modifications to the device are not subject to
warranty.
This device contains no user-serviceable parts. Refer servicing to qualified technicians only.
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance of
this manual or any unauthorized modification to the device.
•Never let the power cord come into contact with other cables! Handle the power cord and all
connections with the mains with particular caution!
•Never remove warning or informative labels from the unit.
•Never use anything to cover the ground contact.
•Never lift the fixture holding it by the projector-head, as the mechanics may be damaged. Always
hold the fixture by the transport handles.
•Never place any material over the lens.
•Never look directly into the light source.
•Never leave any cables lying around.
•Never loosen the screws of the rotating gobo otherwise you risk opening of the ball bearing.
•Do not insert objects into air vents.
•Do not connect this device to a dimmerpack.
•Do not switch the device on and off in short intervals, as this will reduce the device’s life.
•Do not touch the device’s housing bare-handed during its operation (housing becomes very hot).
Allow the fixture to cool for at least 5 minutes before handling.
•Do not shake the device. Avoid brute force when installing or operating the device.
•Only use the device indoors, avoid contact with water or other liquids.
•Only operate the fixture after having checked if the housing is firmly closed and all screws are tightly
fastened.
•Only operate the device after having familiarized with its functions.
•Avoid flames and do not put close to flammable liquids or gases.
•Always keep the case closed while operating.
•Always allow a free air space of at least 50 cm around the unit for ventilation.
•Always disconnect power from the mains, when device is not used or before cleaning! Only handle
the power cord holding it by the plug. Never pull out the plug by tugging the power cord.
•Make sure that the device is not exposed to extreme heat, moisture or dust.
•Make sure that the available voltage is not higher than stated on the rear panel.
•Make sure that the power cord is never crimped or damaged. Check the device and the power
cord from time to time.
•If the lens is obviously damaged, it has to be replaced.
•If device was dropped or struck, disconnect mains power supply immediately. Have a qualified
engineer inspect for safety before operating.
•If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not
switch it on immediately. The arising condensation water might damage your device. Leave the
device switched off until it has reached room temperature.
•If your Showtec device fails to work properly, discontinue the use immediately. Pack the unit securely
(preferably in the original packing material), and return it to your Showtec dealer for service.
•For adult use only. Moving head must be installed beyond the reach of children. Never leave the unit
running unattended.
•Never attempt to bypass the thermostatic switch or fuses.
•For replacement use fuses of same type and rating only.

4
Ordercode: 42562
Wipe Out 360 RGBW
•The user is responsible for correct positioning and operating of the Wipe Out. The manufacturer will
not accept liability for damages caused by the misuse or incorrect installation of this device.
•This device falls under protection class I. Therefore it is essential to connect the yellow/green
conductor to earth.
•During the initial start-up some smoke or smell may arise. This is a normal process and does not
necessarily mean that the device is defective.
•Repairs, servicing and electric connection must be carried out by a qualified technician.
•WARRANTY: Till one year after date of purchase.
Operating Determinations
•This device is not designed for permanent operation. Consistent operation breaks will ensure that the
device will serve you for a long time without defects.
•The minimum distance between light output and the illuminated surface must be bigger than 1
meter.
•The maximum ambient temperature ta= 40°C must never be exceeded.
•The relative humidity must not exceed 50 % with an ambient temperature of 40° C.
•If this device is operated in any other way than the one described in this manual, the product may
suffer damages and the warranty becomes void.
•Any other operation may lead to dangers like short-circuit, burns, electric shock, crash, etc.
You endanger your own safety and the safety of others!
Rigging
Please follow the European and national guidelines concerning rigging, trussing and all
other safety issues.
Do not attempt the installation yourself !
Always let the installation be carried out by an authorized dealer !
Procedure:
•If the projector is lowered from the ceiling or high joists, professional trussing systems have to be used.
•Use a clamp to mount the projector, with the mounting bracket, to the trussing system.
•The projector must never be fixed swinging freely in the room.
•The installation must always be secured with a safety attachment, e.g. an appropriate safety net or
safety cable.
•When rigging, derigging or servicing the projector, always make sure, that the area below the
installation site is secured and that there are not any unauthorized people around.

5
Ordercode: 42562
Wipe Out 360 RGBW
The Wipe Out can be placed on a flat stage floor or mounted to any kind of truss with a clamp and
quick-locks.
Improper installation can cause serious injuries and/or damage of property!
Connection with the mains
Connect the device to the mains with the power-plug.
Always check if the right color cable is connected to the right place.
International
EU Cable
UK Cable
US Cable
Pin
L
BROWN
RED
YELLOW/COPPER
PHASE
N
BLUE
BLACK
SILVER
NEUTRAL
YELLOW/GREEN
GREEN
GREEN
PROTECTIVE GROUND
Make sure that the device is always properly connected to the earth!
Improper installation can cause serious injuries and/or damage of property!

6
Ordercode: 42562
Wipe Out 360 RGBW
Return Procedure
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.
Package must be clearly labeled with a Return Authorization Number (RMA number). Products returned
without an RMA number will be refused. Highlite will not accept the returned goods or any responsibility.
Call Highlite 0031-455667723 or mail [e-mail] and request an RMA prior to shipping the fixture.
Be prepared to provide the model number, serial number and a brief description of the cause for the
return. Be sure to properly pack fixture, any shipping damage resulting from inadequate packaging is the
customer’s responsibility. Highlite reserves the right to use its own discretion to repair or replace
product(s). As a suggestion, proper UPS packing or double-boxing is always a safe method to use.
Note: If you are given an RMA number, please include the following information on a piece of paper
inside the box:
01) Your name
02) Your address
03) Your phone number
04) A brief description of the symptoms
Claims
The client has the obligation to check the delivered goods immediately upon delivery for any short-
comings and/or visible defects, or perform this check after our announcement that the goods are at their
disposal. Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be
reported to the carrier upon receipt of merchandise.
It is the customer's responsibility to report and submit claims with the shipper in the event that a fixture is
damaged due to shipping. Transportation damage has to be reported to us within one day after receipt
of the delivery.
Any return shipment has to be made post-paid at all times. Return shipments must be accompanied with
a letter defining the reason for return shipment. Non-prepaid return shipments will be refused, unless
agreed otherwise in writing.
Complaints against us must be prepared in writing or sent by fax within 10 working days after receipt of
the invoice. After this period complaints will not be handled anymore.
Complaints will only then be considered if the client has so far complied with all parts of the agreement,
regardless of the agreement from which the obligation is resulting.

7
Ordercode: 42562
Wipe Out 360 RGBW
Description of the device
Features
The Wipe Out 360 RGBW is an innovative concept and brings continuous rotating to LED Bars in a
compact housing but still with a surprisingly high light output.
•Very fast movement
•Continuous pan-rotation
•Light source: 4 x 10W RGBW LED
•Output@2m: 7000lux
•Input voltage: 100-240V, 60/50Hz
•Power consumption: 60W
•DMX channels: 1, 22, 26
•Clear LCD display for easy setup
•Sound Control
•Control modes: DMX, Auto, Manual, Sound, Slave
•Control protocol: DMX-512
•5-pin DMX signal connector IN/OUT
•3-pin DMX signal connector IN/OUT
•Blue-White power connector IN/OUT 100-240V
•Dimmer: 0-100%
•Strobe: 0-20Hz
•Pan: 540° or continuous, depending on DMX Channel
•Tilt: 200°
•Pan/Tilt resolution: 16-bit
•Beam Angle: 3°
•IP-Rating: IP20
•Housing: Metal & Flame retardant plastic
•Dimensions: 555 x 94 x 220 mm (LxWxH)
•Weight: 6,9 kg
Overview
Fig. 01

8
Ordercode: 42562
Wipe Out 360 RGBW
Frontside
Fig. 02
01) Moving head with 4 x 10W RGBW lenses
02) LCD Display + control buttons
03) 5-pin DMX signal connector OUT
04) 5-pin DMX signal connector IN
05) Power switch ON/OFF
06) Fuse 5S3A/250V
Backside
Fig. 03
07) Blue-White power connector IN 100-240V
08) Blue-White power connector OUT 100-240V
09) 3-pin DMX signal connector IN
10) 3-pin DMX signal connector OUT

9
Ordercode: 42562
Wipe Out 360 RGBW
Installation
Remove all packing materials from the Wipe Out 360 RGBW. Check if all foam and plastic padding is
removed. Connect all cables.
Do not supply power before the whole system is set up and connected properly.
Always disconnect from electric mains power supply before cleaning or servicing.
Damages caused by non-observance are not subject to warranty.
Set Up and Operation
Follow the directions below, as they pertain to your preferred operation mode.
Before plugging the unit in, always make sure that the power supply matches the product specification
voltage. Do not attempt to operate a 120V specification product on 230V power, or vice versa.
Connect the device to the main power supply. The device can be sound-controlled as it is equipped
with a built-in microphone.
Control Modes
There are 5 modes:
•Stand-alone (Auto)
•Manual
•Sound-controlled
•Master/Slave
•DMX-512 (1, 22, 26CH)
One Wipe Out (Auto and Manual)
01) Fasten the effect light to a firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Plug the end of the electric mains power cord into a proper electric power supply socket.
03) When the Wipe Out is not connected with a DMX cable, it functions as a stand-alone device.
Please see pages 16-18 for more information about the Auto Mode and Manual Mode.
One Wipe Out (Sound-controlled)
01) Fasten the effect light to a firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Plug the end of the electric mains power cord into a proper electric power supply socket.
03) Turn on the music. If the device is set to sound-control, then the Wipe Out will react to the beat of
the music. Please see page 18 for more information about the sound-control options.
Multiple Wipe Outs (Master/Slave control)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Use a 3-pin XLR cable to connect the Wipe Out.
The pins:
01) Earth
02) Signal -
03) Signal +
03) Link the units as shown in fig. 04. Connect the first unit's DMX "out" socket with the second unit's "in"
socket, using a DMX-signal cable. Repeat this process to link the second, third, and fourth units.
You can use the same functions on the master device as described on page 18 (Auto Mode or
Sound-controlled Mode). This means that you can set your desired operation mode on the master
device and all slave devices will react the same as the master device.

10
Ordercode: 42562
Wipe Out 360 RGBW
Multiple Wipe Outs (Master/Slave control)
Fig. 04
Multiple Wipe Outs (DMX Control)
01) Fasten the effect light to a firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Use a 3-pin or 5-pin XLR cable to connect the Wipe Outs and other devices.
04) Link the units as shown in fig. 05. Connect the first unit's DMX "out" socket with the second unit's "in"
socket, using a DMX-signal cable. Repeat this process to link the second, third, and fourth units.
05) Supply electric power: Plug electric mains power cords into each unit's IEC socket, then plug the
other end of the mains power cord into proper electric power supply sockets, starting with the first
unit. Do not supply power before the whole system is set up and connected properly.

11
Ordercode: 42562
Wipe Out 360 RGBW
Multiple Wipe Outs DMX Set Up
Fig. 05
Note : Link all cables before connecting electric power
Fixture Linking
You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller or to
run synchronized shows of two or more fixtures set to a master/slave operating mode. The combined
number of channels required by all the fixtures on a serial data link determines the number of fixtures the
data link can support.
Important:
Fixtures on a serial data link must be daisy-chained in a single line. To comply with the
EIA-485 standard, no more than 30 devices should be connected on one data link.
Connecting more than 30 fixtures on one serial data link without the use of a DMX optically
isolated splitter may result in deterioration of the digital DMX signal.
Maximum recommended DMX data link distance: 100 meters
Maximum recommended number of fixtures on a DMX data link: 13 fixtures
Maximum recommended number of Wipe Outs on a PowerCon link: 7 fixtures@110V
Maximum recommended number of Wipe Outs on a PowerCon link: 13 fixtures@240V
Data Cabling
To link fixtures together, you must obtain data cables. You can purchase DAP Audio certified DMX cables
directly from a dealer/distributor or construct your own cable. If you choose to create your own cable,
please use data-grade cables that can carry a high quality signal and are less prone to electromagnetic
interference.
DAP Audio Certified DMX Data Cables
•DAP Audio Basic microphone cable for allround use. bal. XLR/M 3 p. > XLR/F 3 p.
Ordercode: FL01150 (1,5m.), FL013 (3m.), FL016 (6m.), FL0110 (10m.), FL0115 (15m.), FL0120 (20m.).
•DAP Audio cable for the demanding user with exceptional audio-qualities and connector made by
Neutrik®. Ordercode: FL71150 (1,5m.), FL713 (3m.), FL716 (6m.), FL7110 (10m.).

12
Ordercode: 42562
Wipe Out 360 RGBW
The Wipe Out 360 RGBW can be operated with a controller in control mode or without the controller in
stand-alone mode.
Control Panel
A) LCD display
B) MODE button
C) SETUP button
D) UP button
E) DOWN button
Fig. 06
Control Mode
The fixtures are individually addressed on a data-link and connected to the controller.
The fixtures respond to the DMX signal from the controller. (When you select the DMX address and save it,
the controller will display the saved DMX address, next time.)
DMX Addressing
The control panel on the front side of the base allows you to assign DMX fixture addresses, which is the first
channel with which the Wipe Out will respond to the controller.
Please note, when you use the controller, the unit has 26 channels.
When using multiple Wipe Outs, make sure you set the DMX addresses right.
Therefore, the DMX address of the first Wipe Out should be 1(001); the DMX address of the second Wipe
Out should be 1+26=27 (027); the DMX address of the third Wipe Out should be 27+26=53 (053), etc.
Please, be sure that you do not have any overlapping channels in order to control each Wipe Out
correctly. If two or more Wipe Outs are addressed similarly, they will work similarly.
Controlling:
After having addressed all Wipe Out fixtures, you may now start operating these via your lighting
controller.
Note: After switching on, the Wipe Out will automatically detect whether DMX 512 data is received or
not. If there is no data received at the DMX-input, the “LED “ on the control panel will not flash.
If not, the problem may be:
•The XLR cable from the controller is not connected with the input of the Wipe Out 360 RGBW.
•The controller is switched off or defective, the cable or connector is detective, or the signal wires are
swapped in the input connector.
Note: It is necessary to insert an XLR termination plug (with 120 Ohm) in the last fixture in order to ensure
proper transmission on the DMX data link.

13
Ordercode: 42562
Wipe Out 360 RGBW
Menu Overview
See next page for the remaining menu functions.

14
Ordercode: 42562
Wipe Out 360 RGBW

15
Ordercode: 42562
Wipe Out 360 RGBW
Main Menu Options
Manual Mode
Auto Mode
Sound-controlled Mode
DMX-512 Mode
Master/Slave Mode
Settings
1. Manual Mode
01) While in the main menu, press the MODE button until the display shows .
02) Press the SETUP button to enter the menu.
03) Press the UP and DOWN buttons to toggle between the 3 options:
1.1 LED
1.2 Pan
1.3 Tilt
1.1 Manual Mode - LED
01) When the display shows , press the SETUP button to enter the LED adjustment menu.
02) Press the UP and DOWN buttons to toggle between the 3 adjustable options:
Auto
Color
Dimmer
03) When the display shows , press the SETUP button to enter the menu.
04) Press the UP and DOWN buttons to toggle between the 2 adjustable options:
Speed
Frequency
05) When the display shows , press the SETUP button to enter the menu.
06) You can now adjust the speed of your light show. The adjustment range is between
, from slow to fast.
07) When the display shows , press the SETUP button to enter the menu.
08) You can now adjust the strobe frequency. The adjustment range is between .
09) The device will now run a manual show, with the previously adjusted characteristics.
10) Press the MODE button to return to step 2 and press the UP and DOWN buttons until the display shows
.
11) Press the SETUP button to enter the menu.
12) Press the UP and DOWN buttons to toggle between the 2 adjustable options:
Static
Frequency
13) When the display shows , press the SETUP button.
14) Press the UP and DOWN buttons to adjust the LED colors. You can choose from the following options:
All on
Light blue
Light green
Light red
Purple

16
Ordercode: 42562
Wipe Out 360 RGBW
Cyan
Yellow
White
Blue
Green
Red
Black (Blackout)
15) Press the MODE button to return to step 12 and press the UP and DOWN buttons until the display
shows .
16) Press the SETUP button to enter the menu.
17) Press the UP and DOWN buttons to adjust the strobe frequency. The adjustment range is between
.
18) Press the MODE button to return to step 2, press the UP and DOWN buttons until the display shows
.
19) Press the SETUP button to enter the menu.
20) Press the UP and DOWN buttons to toggle between the following colors:
Red
Green
Blue
White
Frequency
21) If the display shows Red, Green, Blue or White, press the SETUP button to proceed to the LED intensity
adjustment:
22) Press the UP and DOWN buttons to adjust the intensity. The adjustment range for each color is
between 0-255, from dark to brightest.
23) When the display shows , press the SETUP button to enter the strobe settings.
24) Press the UP and DOWN buttons to adjust the strobe intensity. The adjustment range is between
1.2 Manual Mode - Pan
01) Repeatedly press the MODE button until the display shows .
02) Press the UP and DOWN buttons until the display shows .
03) Press the SETUP button to enter Pan adjustment.
04) Press the UP and DOWN buttons to toggle between the 4 options:
p-Auto
p-Manul
p-CCW
p-CW
05) When the display shows , press the SETUP button to enter. In this mode, it is not possible to
adjust the pan parameters.
06) When the display shows , press the SETUP button to enter.
07) Press the UP and DOWN buttons to manually adjust pan movement. The adjustment range is
between .
08) When the display shows , press the SETUP button to enter the menu.
09) Press the UP and DOWN buttons to manually adjust the speed of counterclockwise pan movement.
The adjustment range is between , from slow to fast.

17
Ordercode: 42562
Wipe Out 360 RGBW
10) When the display shows , press the SETUP button to enter the menu.
11) Press the UP and DOWN buttons to manually adjust the speed of clockwise pan movement. The
adjustment range is between .
1.3 Manual Mode - Tilt
01) Repeatedly press the MODE button until the display shows .
02) Press the UP and DOWN buttons until the display shows .
03) Press the SETUP button to enter Tilt adjustment.
04) Press the UP and DOWN buttons to toggle between the 2 options:
t-Auto
t-Manul
05) When the display shows , press the SETUP button to enter. In this mode, it is not possible to
adjust the tilt parameters.
06) When the display shows , press the SETUP button to enter.
07) Press the UP and DOWN buttons to manually adjust tilt movement. The adjustment range is between
.
2. Built-in Program Mode
01) While in the main menu, press the UP and DOWN buttons until the display shows .
02) Press the SETUP button to enter the Auto Mode.
03) Press the UP and DOWN buttons to choose the desired automatic show. The adjustment range is
between .
04) The device will now run the chosen automatic show.
3. Sound-controlled Mode.
01) While in the main menu, press the UP and DOWN buttons until the display shows .
02) Press the SETUP button to enter the Sound-controlled Mode.
03) Press the UP and DOWN buttons to adjust the sound sensitivity of the device. The adjustment range is
between , from low to high sensitivity.
04) The device will now react to the beat of the background music.
4. DMX-512 Mode
01) While in the main menu, press the UP and DOWN buttons until the display shows .
02) Press the SETUP button to enter the menu.
03) Press the UP and DOWN buttons to toggle between the 2 options:
Address
Channel
04) When the display shows , press the SETUP button to enter DMX address settings.
05) Press the UP and DOWN buttons to choose the desired DMX address. The adjustment range is
between .
06) When the display shows , press the SETUP button to enter channel mode menu.
07) Press the UP and DOWN buttons to choose one of the 3 channel modes:
1 channel
22 channels
26 channels
5. Master/Slave Mode
01) While in the main menu, press the UP and DOWN buttons until the display shows .
02) The device is now operating in Slave Mode. It means that it will react the same as the master device.

18
Ordercode: 42562
Wipe Out 360 RGBW
6. Settings
01) While in the main menu, press the UP and DOWN buttons until the display shows .
02) Press the UP and DOWN buttons to toggle between the following options:
6.1 BL time
6.2 Adjust
6.3 Reset
6.4 Power
6.5 Error
6.6 Lamp
6.7 Use
6.8 Sensor
6.9 About
6.1 Settings –BL Time
01) When the display shows , press the SETUP button to enter the display blackout settings.
02) Press the UP and DOWN buttons to choose one of the following options:
On (display continuously ON)
5s (display turns OFF after 5 seconds)
10s (display turns OFF after 10 seconds)
20s (display turns OFF after 20 seconds)
30s (display 30s turns OFF after 30 seconds)
6.2 Settings –Adjust
01) When the display shows , press the SETUP button to enter pan/tilt manual adjustment.
02) When the display shows , press the SETUP button to enter pan adjustment.
03) Press the UP and DOWN buttons to adjust pan. Both, positive and negative values, are possible.
04) When the display shows , press the SETUP button to enter tilt adjustment.
05) Press the UP and DOWN buttons to adjust tilt. Both, positive and negative values, are possible.
6.3 Settings –Reset
01) When the display shows , press the SETUP button to enter the menu.
02) When the display shows , press the SETUP button to run the reset or the MODE button to cancel
the reset.
6.4 Settings –Power
01) When the display shows , press the SETUP button to view the information about the output
power.
02) Press the UP and DOWN buttons to view the information about the main or LED output power.
6.5 Settings –Error
01) When the display shows , press the SETUP button to enter the menu.
02) The device will check for all possible software errors, while displaying current status: .
03) Press the SETUP button to complete the operation. If there were not any errors, the display will show
.
6.6 Settings –Lamp
01) When the display shows , press the SETUP button to view the light output information: .
6.7 Settings –Use
01) When the display shows , press the SETUP button to check for how long the device has already
been used.
02) When you press the SETUP button, the display will show .
03) Press the SETUP button to perform time reset or the MODE button to cancel time reset.

19
Ordercode: 42562
Wipe Out 360 RGBW
6.8 Settings –Sensor
01) When the display shows , press the SETUP button to enter the sensor settings.
02) Press the UP and DOWN buttons to toggle between the following 4 options:
p-hall
t-hall
p-Rast
t-Rast
03) When the display shows , press the SETUP button to view the pan sensor state.
04) If there are not any errors, the display will show .
05) When the display shows , press the SETUP button to view the tilt sensor state.
06) If there are not any errors, the display will show .
07) When the display shows , press the SETUP button to enter the pan correction menu.
08) Press the UP and DOWN buttons to toggle between the 2 options:
p-Sets
p-State
09) When the display shows , press the SETUP button to enter the menu.
10) Press the UP and DOWN buttons to enable or disable the pan correction.
If enabled, the device will reset the pan position to its default setting, whenever there is any
deviation from it.
11) When the display shows , press the SETUP button to enter the menu.
12) Press the UP and DOWN buttons to toggle between the 2 options:
history (general number of the corrections performed on the device)
current (number of corrections performed on the device since it has been switched on)
13) Press the SETUP button to reset both, history and current status.
14) When the display shows , press the SETUP button to run the reset, or the MODE button to
cancel the reset.
15) Repeatedly press the MODE button to return to step 7 and press the UP and DOWN buttons until the
display shows .
16) Press the SETUP button to enter the tilt correction menu.
17) Press the UP and DOWN buttons to toggle between the 2 options:
t-Sets
t-State
18) When the display shows , press the SETUP button to enter the menu.
19) Press the UP and DOWN buttons to enable or disable the tilt correction.
If enabled, the device will reset the tilt position to its default setting, whenever there is any deviation
from it.
20) When the display shows , press the SETUP button to enter the menu.
21) Press the UP and DOWN buttons to toggle between the 2 options:
history (general number of the corrections performed on the device)
current (number of corrections performed on the device since it has been switched on)
22) Press the SETUP button to reset both, history and current status.
23) When the display shows , press the SETUP button to run the reset, or the MODE button to
cancel the reset.
6.9 Settings –About
01) Repeatedly press the MODE button to return to step 1 and press the UP and DOWN buttons until the
display shows .
02) Press the SETUP button to enter the menu.
03) Repeatedly press the UP and DOWN buttons to view the current versions of the LED, engine, software
and model.