INNOVAPLAS BILTMOR 5050 WITH SELF-LATCHING 9600 User manual

REV. 02/26/2020 PN: PG:1
2257 route 139
Drummondville, Québec
J2A 2G2
1 year on step and closure.
1 year on hardware.
MANUFACTURER WARRANTY
WWW.INNOVAPLAS.COM
Required tools (not included)
A
1) Insert the two gussets in the slots and slide them
toward the corners.
2) Assemble the two main modules with the six screws,
nuts and washers provided.
3) Snap the door between the top and bottom module
within the slots provided.
Sand
(not included)
Sand
5 lbs
x6 x6 x6
A B C
BILTMOR 5050 WITH SELF-LATCHING 9600
Contents of Biltmor box SKU # 5050
Security strap
x2
x2 x2
(3/4 IN.)
x12
(2 1/2 IN.)
x2
SCREW KIT 140-0016
(2 1/2 IN.)
FG D C
Contents of Self-Latching box SKU # 9600
x2
x4
x3
A weather-resistant padlock
is recommended.
MAXIMUM functional
width is 1/4’’.
WARNING
Install the step on a flat surface.
Do not jump or dive from the step or ladder.
Remove the step from water when temperatures drop below freezing.
In winter, the step should be stored in an area protected from snow.
Never lift the step by its handrails.
Use BATTERY operated tools to avoid electric shock near water.
Ensure no corrosive materials are added to the step or harware kit.
The step must be installed per manufacturer’s instructions.
File off all stripped or sharp edges before assembly to avoid injuries
and liner damage.
The manufacturer is not responsible for damages or injuries caused
by improper installation or use of product.
To ease the installation of handrails and bolts, use a screwdriver to
line up the holes.
2X
GUSSET
INSERT NUT
Phillips #2 Phillips #3
7/16 wrench
Phillips bit
x2
x4
x2
(3/4 IN.)
x4
D
SCREW KIT 140-0067
x6 x6 x6
(1 IN.)
(1 ¹⁄2 IN.)
(³⁄4 IN.)
x2
(³⁄4 IN.)
x24 x12
AB C D E F
SCREW KIT 140-0010
Contents of “Riser kit” box
x4
x2
x2
x4
x1
x2
x2

REV. 02/26/2020 PN: PG:2
2257 route 139
Drummondville, Québec
J2A 2G2
WWW.INNOVAPLAS.COM
1 year on step and closure.
1 year on hardware.
MANUFACTURER WARRANTY
BILTMOR 5050 WITH SELF-LATCHING 9600
D
B
E
C
D
1) Fill the bag provided with sand.
The approximate weight should
be 5 lbs.
*SAND
1) Slide the two tie
wraps in place and
place the sand bags
into the riser.
2) Fasten the tie wraps.
Do not overtighten.
4x
4x
*Sand not included
F
x3
D
x2
3
1
/
4
”
1/4”
align screws from
center of plate
E
point 4
point 1
1) Insert the two step cups in the riser.*
2) Place the riser on the ground, install the step
on top of the riser and fasten with the four
screws and plastic screw caps provided.
3) Snap the screw caps covers in place.
* View step cups installation tips on YouTube:
https://www.youtube.com/watch?v=W5RH1VNxpu0
1) Snap the four post ends into the
step, making sure that the cylindrical
part is vertical and that the ends are
snapped properly in their respective
housings.
2) Snap the two feet to the bottom of
the step.
x20
1) Insert the four posts into the post
ends and secure them in place with the
screws provided (see right).
2) Insert the platform over the 2 rear
posts.
3) Insert the small and large handrails
as illustrated. Secure the large
handrails with the screws provided.
Leave the small handrails floating.
4)
Fasten the access panel with the screws
provided (see right).
D

H
Security strap
1) Once the step is in the
pool secure the platform
to the top seat (see
illustration) using the two
straps provided.
x2
OPTIONAL:
Once the pool step has been
completely assembled and
secured to the pool, attach the
2 screws supplied through the
platform to the top seat of your
pool to provided a more rigid
assembly.
x2
F
1) Slowly submerge the step into
the pool. Make sure you do not
damage the pool liner in the
process.
2) Angle the whole step so that it
is entirely under water. Purge all
the air from under the step.
REV. 02/26/2020 PN: PG:3
2257 route 139
Drummondville, Québec
J2A 2G2
WWW.INNOVAPLAS.COM
1 year on step and closure.
1 year on hardware.
MANUFACTURER WARRANTY
BILTMOR 5050 WITH SELF-LATCHING 9600
K
G
I J
1) Insert the two posts into
the rear holes of the step.
2) Force the posts to a
vertical position flush with
the rear surface and
secure in place with the
bolts and nuts provided.
3) Insert the two post
covers.
x2
x2
G
C
WARNING
LOCK THE DOOR TO THE
STEP WITH A PADLOCK
WHEN THE POOL IS NOT
IN USE TO PREVENT
DROWNING AND
UNAUTHORIZED ENTRY.
1) Slide the Self-Latching
posts through the
platform and small
handrails.
2) Secure the platform
using the screws
provided.
3) Secure the small
handrails to the posts
with the screws provided.
4) Insert the four post
covers on the handrails.
x12
D