ShowEx XMT-275 Vee Pro User manual

© Trynex International 2008 L1184
4 — 25
XMT-275 Vee Pro Express Mount Kit
Mounting Instructions
IN BED EXPRESS MOUNT
Step 1: Locate left and right side mounting rail and .
Step 2: Locate item cross rails.
Step 3: Assemble items , , together per exploded view. (Accessory Shim may be needed for adjustment).
Step 4: Install rear latches items and with 5/8" thin lock nut .
Step 5: Place frame assembly on truck and center left to right.
Step 6: Install items , & per illustration. Note: on older models, you will have to drill out frame to accept item stop
bolt. To do this, you will need to bolt item to lower frame rail using a drill template to locate the bracket, drill all four
holes and then install items , & .
Step 7: Determine front to back location by either placing spreader into locked position into frame assembly or by measuring
using rear side frame holes and measuring to rear of pick up bed. Mark holes with paint marker or scribe. Verify that
there are no critical components below the pick up bed such as a gas tank, etc.
Step 8: Drill holes and mount frame using supplied 5/8" hardware. Note: There are alternate holes for drilling around items that
may be in the way.
WHEEL KIT
Step 1: Assemble item to item using supplied hardware.
Step 2: Assemble items to item using supplied hardware.
Step 3: With spreader in truck, place item wheel arm on the rear center of upper rail of hopper (see illustration/pictures).
Step 4: Place item on auger weldment and trap the lower edge while at the same time positioning item to engage item
so that item pin with ring can keep the two assemblies together.
Step 5: Lock swivel wheels.
Step 6: Pull spreader back and o the in bed mount, allow spreader to rotate towards ground with the locked wheels
touching rst.
Step 7: Continue to pull spreader into a vertical position.
Step 8: When everything is stable, release wheel locks and slowly move spreader to storage location. Lock wheels when
nal place has been established.
Step 9: See photo and drawing illustrations for assembly and installation.
Note: Ratchet straps must still be used as part of the mounting system.

© Trynex International 2008 L1184
4 — 26
XMT-275 Express Mount Kit
Parts Breakdown
.ytQnoitpircseD.oNtraPyeK
D 6590
D 6589
D 6591
6595D
D 6593
D 6592
D 6573
D 6594
D 4127
D 4116
D 6581
D 4120
D 4124
D 4121
D 6572
D 6567
D 6570
D 6576
D 6138
D 6568
D 6569
D 6587
D 5717
Mounting Rail Left
Mounting Rail Right
Cross Rail
Backing Plate
Stop Latch Lt Side
Stop Latch Rt Side
5/8” Thin Lock Nut
Special Stop Bolt
5/8” Lock Nut
1/2-13 x 1-1/2” Hex Bolt
1/2” Fender Washer
1/2” Lock Nut
3/8-16 Lock Nut
3/8-16 x 1” Hex Bolt
Wheel Ball Pin
Wheel Cross Bar
Wheel Pivot w/Lock
5/16-18 x 1-1/4” Hex Bolt
5/16-18 Lock Nut
Wheel Foot Holder
Wheel Arm
3/8-16 x 2-1/2 HHCS Bolt
Nylon Spacer Bushing
1
1
2
4
1
1
2
4
4
8
8
8
5
4
1
1
2
12
12
1
1
1
4
Use Bushings To Space
frame out if required.