Sichuan AnSphere Technology NRF52810 User manual
BUNN PCBA User Manual
2 / 8
Revision History
Version
Description
Author
Date
V0.1
Initial version
Juan He
11-30-2021
V0.2
Complete instructions
Juan He
7-12-2021
BUNN PCBA User Manual
3 / 8
Contents
1 Instruction..................................................................................................................................................................... 4
2 Components.................................................................................................................................................................. 4
2.1 Hardware list......................................................................................................................................................4
2.2 Software list.......................................................................................................................................................4
3 Operation steps............................................................................................................................................................. 4
3.1 Hardware preparation........................................................................................................................................ 4
3.2 Software preparation......................................................................................................................................... 5
3.3 AT command debug...........................................................................................................................................7
4 Support..........................................................................................................................................................................8
BUNN PCBA User Manual
4 / 8
1 Instruction
BUNN is based on Microsoft Azure Sphere OS and provides end-to-end IoT security solutions.
BUNN has been configured with multiple interfaces including BLE, Ethernet, RS232,SD,USB.
Product features：
●Data storage: support to read & write SD from MT3620 through SPI and PC through USB
●Data transfer: support to data transfer through BLE, Ethernet, RS232,SD,USB
●BLE configuration: support to configure communication ways through BLE by APP
●Operating ambient temperature range: -30°C to +70°C (-22°F to 158°F)
●Operating ambient humidity: 10-95%
2 Components
2.1 Hardware list
Item
Number
Description
BUNN
1
Main product
Debug Dongle cable(optional)
1
Azure sphere debug cable
SD Card(optional)
1
Memory flash for main board
USB flash disk(optional)
1
Reading components for main board
5V2A DC Power Adapter(optional)
1
Power for main board
2.2 Software list
Item
Version
Description
bunn_sd_singed.imagepackage
1.0
Main executable program
lan-enc28j60-isu0-int5_signed.im
agepackage
1.0
Northbound network driver
3 Operation steps
3.1 Hardware preparation
BUNN PCBA interfaces shows in figure 1.
1. Connect power cables to BUNN
BUNN PCBA User Manual
5 / 8
2. Insert SD card to BUNN
3. Insert USB to BUNN
4. Connect Ethernet
5. Connect BUNN to PC through USB
6. Connect dongle to BUNN through mini HDMI
Figure 1. Device interfaces Figure 2. UART Pins
3.2 Software preparation
1. Format one SD card with FAT32 file system
BUNN PCBA User Manual
6 / 8
Figure 3 formatting SD
2. Download images
Download command：
(1) azsphere device sideload deploy --force --imagepackage G:\bunn_sd_singed.imagepackage
(2) azsphere device sideload deploy --force --imagepackage
G:\lan-enc28j60-isu0-int5_signed.imagepackage
BUNN PCBA User Manual
7 / 8
Figure 4 Download command
3.3 AT command debug
1. Download serial tool for debug.
2. Configure serial tool
(1) Port: use the serial port
(2) Parity: None
(3) Flow control：None
(4) Baud rate: 115200
(5) Data bits: 8
(6) Stop bits:1
Figure 5 SSCOM configuration
3. AT commands for debug
AT command
AT command note
AT response
AT response
note
AT+1
Request to connect RS232
AT+1
Success
BUNN PCBA User Manual
8 / 8
AT+2
Request to start LED
AT+2-ok
AT+2-fail
Success
Fail
AT+3
Request to stop LED
AT+3-ok
AT+3-fail
Success
Fail
AT+4
Request to connect Ethernet
AT+4-ok
AT+4-fail
Success
Fail
AT+6
Request to R/W SD through MT3620
AT+6-ok
AT+6-fail
Success
Fail
AT+7
Request to get MAC of BLE
AT+7+MAC
Success
AT+8
Request to get power down information
AT+8-ok
AT+8-fail
Power down
Power on
AT+9
Request to R/W SD through PC
AT+9-ok
AT+9-fail
Success
Fail
AT+0
Request to R/W USB through PC
AT+0-ok
AT+0-fail
Success
Fail
AT+d
Request to open watch-dog
AT+d-ok
AT+d-fail
Success
Fail
Table 1 AT commands
4 Support
Contact:
1. Email: crl@changhong.us
2. Phone: 1-408-970-0349
3. Address: 3945 Freedom Circle, Suite 320, Santa Clara, CA 95054
5 FCC ID Label
FCC NOTE FOR MODULER STATMENT
1.1 List of applicable FCC rules:
The module complies with FCC Part 15.247.
1.2 Summarize the specific operational use conditions:
The module has been certified for Fix, Mobile, Portable applications.
This transmitter must not be co‐located or operating in conjunction with any other antenna or
transmitter.
1.3 Limited module procedures:
The module has not its own RF shielding, which belong to limited module Standard requires:
Clear and specific instructions describing the conditions, limitations and procedures for third‐parties
to use and/or integrate the module into a host device (see Comprehensive integration instructions
below).
Resolve: Supply example as follows:
Installation Notes:
1) nRF52810 Module Power supply range is DC 3.3V, when you use nRF52810 Module design
product, the power supply cannot exceed this range.
2) When connect nRF52810 Module to the host device, the host device must be power off.
3) Make sure the module pins correctly installed.
4) Make sure that the module does not allow users to replace or demolition.
1.4 Trace antenna designs:
Not applicable.
1.5 RF exposure considerations:
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. The antenna(s) used for this transmitter must not
be collocated or operating in conjunction with any other antenna or transmitter.
Note: the host product manuals must include a statement in order to alert the users of FCC RF exposure
compliance.
1.6 Antennas
The antenna type is a dipole antenna, is permanently attached, can’t be replaced.
1.7 Label and compliance information
This device complies with part 15 of the FCC rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can radiate
radio frequency energy and, if not installed andused in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
‐Reorient or relocate the receiving antenna.
‐Increase the separation between the equipment and receiver.
‐Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
‐Consult the dealer or an experienced radio/TV technician for help.
The system integrator must place an exterior label on the outside of the final product housing the
nRF52810 Modules. Below is the content that must be included on this label.
The host product Labeling Requirements:
NOTICE: The host product must make sure that FCC labeling requirements are met. This includes
clearly visible exterior label on the outside of the final product housing that displays the contents
shown in below:
Contains FCC ID:2A4AD-NRF52810
1.8 Information on test modes and additional testing requirements:
When testing host product, the host manufacture should follow FCC KDB Publication 996369 D04
Module Integration Guide for testing the host products. The host manufacturer may operate their
product during the measurements. In setting up the configurations, if the pairing and call box options
for testing does not work, then the host product manufacturer should coordinate with the module
manufacturer for access to test mode software.
1.9 Additional testing, Part 15 Subpart B disclaimer:
The modular transmitter is only FCC authorized for the specific rule parts (FCC Part 15.247) list on the
grant, and that the host product manufacturer is responsible for compliance to any other FCC rules that
apply to the host not covered by the modular transmitter grant of certification. The final host product
still requires Part 15 Subpart B compliance testing with the modular transmitter installed when contains
digital circuity.
1.10 Information on test modes and additional testing requirements:
When testing host product, the host manufacture should follow FCC KDB Publication 996369 D04
Module Integration Guide for testing the host products. The host manufacturer may operate their
product during the measurements.
Table of contents
