Promax EN-206 User manual

EN-206
HIGH DEFINITION MULTI-STANDARD
MODULATOR
DVB-T
DVB-C - J83.B - J83.C
ATSC-T
ISDB-T*
- 0 MI2148 -

SAFETY NOTES
Read the user’s manual before using the equipment, mainly "SAFETY RULES"
paragraph.
The symbol on the equipment means "SEE USER’S MANUAL". In this manual
December also appear as a Caution or Warning symbol.
WARNING AND CAUTION statements December appear in this manual to avoid
injury hazard or damage to this product or other property.
USER'S MANUAL VERSION
Version Date Software Version
5.0 Novenber 2017 4.05

November 2017
SAFETY RULES
*The safety could not be assured if the instructions for use are not closely
followed.
*When using some of the following accessories use only the specified ones to
ensure safety.:
External DC charger
Power cord
*No use the external DC power cord this is damaged.
*Do not connect the external DC power until all cables are connected properly.
*In el manipulate external DC power supply.
*Observe all specified ratings both of supply and measurement.
*Remember that voltages higher than 70 V DC or 33 V AC rms are dangerous.
*Use this instrument under the specified environmental conditions.
*If the encoder modulator has been kept in cold conditions for a long time, keep it in
a warm room minimum 2 hours before plugging into the mains.
*Mount the device in vertical position with the connectors located on the top side.
*Do not obstruct the ventilation system of the instrument.
*To prevent fire or shock hazard, do not expose this appliance to rain or moisture.
*Use for the signal inputs/outputs, appropriate low radiation cables.
*Follow the cleaning instructions described in the Maintenance paragraph.
*The operator is not allowed to intervene within the team: Any other change on the
equipment should be carried out by qualified personnel.
*Mechanical handling / electric unit can cause damage. Do not connect the appliance
to the mains before or during assembly.

November 2017
* Symbols related to safety:
Descriptive Examples of Over-Voltage Categories
Cat I Low voltage installations isolated from the mains.
Cat II Portable domestic installations.
Cat IIIFixed domestic installations.
Cat IV Industrial installations.

November 2017
TABLE OF CONTENTS
1 INTRODUCTION ........................................................................................ 1
1.1 Description .......................................................................................... 1
1.2 Equipment Details................................................................................. 2
1.3 Installation .......................................................................................... 3
1.4 Cascade Installation .............................................................................. 5
2 OPERATIONS AND MANAGEMENT.............................................................. 6
3 MENU TREE ............................................................................................... 8
3.1 DVB-T................................................................................................. 9
3.2 DVB-C................................................................................................11
3.3 ATSC-T ..............................................................................................13
3.4 ISDB-T* .............................................................................................15
3.5 Parameters definition ...........................................................................17
4 USB PORT ................................................................................................22
4.1 TS Recorder and Save ..........................................................................22
4.1.1 Description ..................................................................................22
4.1.2 Operation ....................................................................................23
4.2 TS Playback ........................................................................................25
4.3 USB upgrade.......................................................................................26
4.4 Disk Usage .........................................................................................26
4.5 Remove Device ...................................................................................27
5 TS CREATOR SOFTWARE...........................................................................28
5.1 Installation .........................................................................................28
5.2 Operations of "TS Creator"....................................................................29
5.3 File Management .................................................................................30
6 WEB-SERVER OPERATION ........................................................................32
6.1 Login .................................................................................................32
6.2 Operation ...........................................................................................33
7 SPECIFICATIONS .....................................................................................43
8 MAINTENANCE .........................................................................................46
8.1 Cleaning Recommendations...................................................................46
9 APPENDIX................................................................................................47
*Special version

November 2017

November 2017 1
HIGH DEFINITION MULTI-STANDARD
MODULATOR
EN-206
1
1INTRODUCTION
1.1 Description
The EN-206 which allow audio/video signal input in TV distributions with
applications in home entertainment, surveillance control, hotel Digital Signage,
shops etc. It is an all-in-one device integrating MPEG4 AVC/H.264 encoding and
modulating to convert input signals to RF out.
The USB port is designed to record encoded video (TS) and save it in ts files in
the USB Keys or Hard Disks, and then the ts files can be playback through the
USB port. The ts files can be also generated on a computer with a specific
software.
The signals source could be from satellite receivers, closed-circuit television
cameras, blu-ray players, and antenna etc. its output signal is to be received by
selected standard TVs or STBs etc.
Figure 1. System Connection Chart.
1Trademark of the DVB - Digital Video Broadcasting Project.

1.2 Equipment Details
Front View
Figure 2.
Up View
Figure 3.
►Grounding: To connect the earth cable.
►DC 12V: Power Input.
►HDMI: HDMI stream input supporting HD signals.
►YPbPr / S-Video / AV: YPbPr / S-Video / AV signal input through a VGA
adapter cable.
►RF in: RF Loop-through input.
2November 2017

November 2017 3
►RF Output: RF output to distribute modulated signal.
►USB Port: For video record, playback and system upgrade.
►Ethernet Port: For web-server management.
1.3 Installation
Mount and tighten the screws and plugs to secure the unit to the wall.
Left 10 cm of free space around from each unit.
Connect the signal input in the respective connectors. The signal source
can be from a surveillance monitor, DVD, set-top box, CCTV and etc.
Optionally, connect the loop-through RF input coaxial cable.
Connect cable to RF output to STB/TV.
Power supply connection: a) Connect the earth cable; b) Connect the
power plug to the unit mains connector; c) Connect the power plug to the
mains socket.
Figure 4.

Figure 5.
4November 2017

November 2017 5
1.4 Cascade Installation
EN-206 unit has 1 TV signal to RF output encoded as Digital TV signal.
Several EN-206 units can be cascaded in order to increase the capacity. The
maximum capacity of a series of N units is 1xN incorporated TV signals. To
cascade 2 or more units, connect the RF output of the preceding unit to the TV
input (loop-through) of the next unit (see right illustration).
Figure 6.

2OPERATIONS AND MANAGEMENT
EN-206 is controlled and managed through the key board and LCD display.
Figure 7.
►LCD Display:
It presents the selected menu and the parameter settings. The backlight in
the display is on when the power is applied.
►LED:
These lights indicate the working status.
Power: It lights on when the power supply is connected.
Alarm: It lights on when the there is error, such as the signal
source loss.
USB: It lights on when the USB device is properly connected
and blocks out when the USB device get removed.
►Left/Right/Up/Down buttons:
Use these buttons to turn the screen pages, shift the target items by moving
the triangle, or change the parameter settings in the program mode.
6November 2017

November 2017 7
►Enter
Use this button to enter a submenu or save a new setting after adjustment;
press it to start adjusting the value of certain items when the corresponding
underline flash with Up and Down buttons.
Figure 8.
Press it to activate the hidden selections and change the setting with Up and
Down (or Left and Right) buttons.
Figure 9.
►Menu:
Press this button to step back.
►Lock:
Locking the screen / cancelling the lock state, and entering the main menu
after the initialization of the device. After pressing lock key, the system will
question the users to save present setting or not.
If not, the LCD will display the current configuration state.
After the initialization of the device, press LOCK to unlock the keyboard. Then
you will be able to browse in the menu tree.

3MENU TREE
When the power is connected, the LCD will start to initialize the program. After
the initialization of the device, press LOCK to unlock the keyboard. Then you will
be able to browse in the menu tree.
The LCD menu goes as below chart. Numbers on the menu refers to the numbers
on the menu tree.
8November 2017

November 2017 9
3.1 DVB-T

Figure 10. DVB-T menu tree.
10 November 2017

November 2017 11
3.2 DVB-C

Figure 11. DVB-C menu tree.
12 November 2017