Siemens ER95351HK Owner's manual

BUILT-IN GAS HOBS
INSTALLATION AND OPERATION INSTRUCTION en
ER94351HK
ER94331HK
ER95351HK

Dear customer,
Congratulations on your choice and thank you for purchasing one of our appliances. This practical,
modern and functional appliance is manufactured using materials of the highest quality which are subject
to strict Quality Control checks throughout the entire manufacturing process. The appliance is meticulously
tested to ensure that it meets your demands and produces perfect cooking results.
Do not remove the appliance from its protective packaging until it is installed in the unit.
Please read these instructions carefully before proceeding to install and use the appliance. The
information contained in these instructions is essential for the correct operation of the appliance and, more
importantly, for your safety.
The packaging of your appliance has been manufactured using only the materials which are strictly
necessary to guarantee efcient protection during transport.
These materials are 100% recyclable, thus reducing the environmental impact. You can also contribute to
caring for the environment, by following the advice below:
- dispose of the packaging in the appropriate recycling bin.
- before you get rid of an old appliance, make sure you disable it. Contact your local authority to nd out
the address of your nearest recycling centre to dispose of your appliance.
- do not pour used oil down the sink. Collect it in a sealed container and take it to an appropriate collection
point or, failing that, place it in the rubbish bin (it will end up in a controlled dump; this is probably not the
best option, but it will avoid contaminating ground water).
IMPORTANT:
In the unlikely event that the appliance should be damaged or not meet your expectations in terms
of quality, please inform us as soon as possible. For the warranty to be valid, the appliance must not
have been tampered with, or used inappropriately.
Preface

2
2
2
8
9
11
12
13
13
14
16
17
17
18
19
20
22
23
23
24
25
25
25
25
26
Packaging of the new hob
Disposal of the old hob
Safety precautions
Placement location
Countertop tapping
Connect to gas pipeline
Gas leak detection
Plug into the socket
Pan supports, caps and burner
Getting familiar with your new hob
Before rst use
Adjusting power
Operation method
Interlink Instruction
Timer
Unsuitable products
Maintenance
Warranty condition
Environmentally-friendly waste management
Table of Contents
Safety Precautions
Your new appliance
Installation
The gas burner operation
Cleaning and Maintenance
Faults
Technical data
Technical Assistance
Service
Used appliances and
packaging
1

All the packaging material are environmental friendly and
recyclable. When you are disposing of these packaging
materials, please do so in such a way that protects the
environment and minimizes waste.
Do not allow children to play with the thin lm or packaging
case to avoid suffocation or accidents.
The old hob should be taken to a recycling center where it
can be disposed of in a way which protects the environment.
Old hobs contain useful materials that can be recycled.
Discarded old electrical appliances can be hazardous to the
environment.
Read these instructions carefully. Reading these instructions
will enable you to use your appliance safely and effectively.
Use approved gas tubing bearing EMSD approval
marking (such as : 機電工程署批准EMSD APPROVAL
GTXXXX) for connection to appliances, or other
appropriate methods accepted by EMSD.
HK Town Gas connection
The operating pressure of this gas hob is 15mbar, therefore
no governor is required.
Attention! According to the Gas Safety Regulations of
Hong Kong, any gas installation works including the
installation of appliances and connection tubing, must
be undertaken by registered gas installers who are
registered for that appropriate classes and be employed
by registered gas contractors.
When installing built-in gas hob on top of stove cabinet,
please check that there is provision for ventilation at the
cabinet to ensure proper operation of the gas hob.
Do not store any ammable materials, sprays or
pressurized containers inside the stove cabinet.
Safety precautions
Packaging of the new hob
Disposal of the old hob
Safety precautions
2
Nameplate

The panel of this built-in hob (on selected model) is
made of tempered glass which is safer than normal
glass for this application. However, the following safety
precautions for using built-in hob with glass top panel
should also be noted in order to prevent the glass top
panel from breaking:
1. Clean the burner assembly frequently to maintain a
clear gas passage on the flame distributor. Clean and
tidy up the flame distributor after spillage of food and
liquid once the burner assembly cooled down.
2. Turn off the gas appliance immediately if abnormal
noise propagates from the gas appliance and contact
gas supply company or gas hob importer for inspection.
3. Do not use oversized utensils for cooking.
4. Do not impact the glass surface with hard objects or
place heavy objects on the glass surface.
Despite using the "TIMER" function (on selected model)
for cooking, user should not leave the gas stove un-
attended.
Please do not use additional fitting, such as aluminum cover.
All operations relating to installation and regulation must be
carried out by a registered gas installer, respecting
applicable regulations, standards and the specifications of
the local gas and electricity providers.
Before installing your new hob, ensure that it is being
installed according to the assembly instructions.
The Towngas model of this built-in cooker has been
exempted from the mandatory requirement for the installation
of external gas governor.
Safety precautions
3

This appliance has been designed for home use only, not for
commercial or professional use. This appliance cannot be
installed on yachts or in caravans. The warranty will only be
valid if the appliance is used for the purpose for which it was
designed.
The place in which the appliance is installed must have fully-
functioning ventilation, in accordance with the regulations.
Do not subject the appliance to draughts. These might blow
out the burner.
This appliance leaves the factory set to the type of gas that is
indicated on the specications plate. It must not be changed
to another type of gas.
Do not tamper with the appliance’s interior. If necessary, call
our Technical Assistance Service.
These operating and installation instructions should be
retained, and passed onto the buyer if the appliance is sold.
Do not switch on the appliance if it is damaged in any way.
Contact our Technical Assistance Service.
The surface of cooking appliances will be heated up during
use. Care must be taken when using these appliances. Keep
children well away from the appliance.
This appliance is only intended for cooking purposes, not as
a heating system.
Fat or oil which is overheated can catch re easily. Do not
leave oil or fats to heat up unattended. If oil or fats do catch
re, never use water to put the re out. Risk of burns! Put the
re out by covering the pan with a lid and switch off the hob.
Safety precautions
4

In the event of a malfunction, turn off the appliance’s gas and
electricity supply. For repairs, call our Technical Assistance
Service.
If one of the controls will not turn, do not force it. Call the
Technical Assistance Service immediately, so that they can
repair or replace it.
Never place unstable pans on the hob or the burners, as
they may accidentally tip over.
Do not clean the hob using a steam cleaner. Risk of
electrocution!
This appliance design and manufactured according to
GB16410-2007 standard for gas appliances: built-in
appliance.
Do not store or use corrosive chemicals, steamers,
ammable materials or non-food products below or near this
domestic appliance.
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
Never let children play with the appliance.
Never leave the appliance unattended during operation.
The graphics in this instruction manual are given as a guide
only.
The manufacturer is exempt from all responsibility if the
requirements of this manual are not complied.
The rst ignition (or ignition after it has been left unused for a
long time) may be difcult, as there is residual air in the gas
pipeline, it may be difcult to light the burner.
Safety precautions
5

Warning: Gas Poisoning
When using the hob, make sure to open the windows or
turner on the exhaust fan of the range hood so as to keep
good ventilation around the gas hob. The gas hob may cause
carbon monoxide poisoning if you are using the gas hob in a
closed kitchen with no ventilation for an extended time.
Warning: Explosion
If you detect a gas leakage while operating the Gas hob,
you should turner off the indoor main gas valve immediately,
and then open windows and doors for ventilation. Do not
use matches or any lighters at this time. Creating a ame at
this time may ignite the residual gas in the room and, cause
an explosion. In the case of a leak, please contact our local
service center immediately.
Warning: Fire
Do not ignite the gas hob for heating when no pan is
placed on it or there is no food in the pan. This may cause
the extraction hood over the gas hob to be damaged by
overheating, or cause a re if the residual grease in the
extraction hood is ignited.
Warning: Risk of burning
Do not let unattended children use or stand next to the gas
hob while it is in use. Once the gas hob has been turned off,
it remains very hot and dangerous for several minutes. At
this time to avoid burn injury, avoid touching the hot burners,
supports and the faceplate around the burners with your
hands or other part of your body.
When using the gas hob, please protect it from external air,
which may cause uneven heating or even extinguish the
ame.
When cooking food with vegetable oil and animal fats, you
should be careful to avoid res caused by overheating oil in
the pan.
Safety precautions
6

If re is caused by overheated oil, immediately use an iron
pot lid or other large metal object to cover the re, in order to
cut off the air needed for burning, and then turn off the indoor
gas valve. In order to avoid accidents, never use water to put
out oil or grease re.
Whenever the burner is extinguished for any reason, you
should turn it off and wait for at least 1 minute before re-
igniting the burner.
Normal operation of gas hob should not cause any unusual
noise. If you have any doubts, please contact our local
service center.
Safety precautions
7

Safety design
Each burner of this gas hob is equipped with a safety device
for the quick cut-off of the gas.
Personal-friendly design
This product inherits and carries forward the precise
processing and manufacturing techniques of Germany, as
well as a human-oriented design concept. Besides the hobs’
convenience and practicality, the gas hob also gives the user
a sense of beauty.
Your new appliance
Production speci cation
Product features
8
ER94351HK
ER95351HK
ER94331HK

This appliance has been designed for home use only. It cannot
be installed on yachts or in caravans.
Do not place the gas hob in the bathroom, bedroom, basement,
corrosive material in close proximity.
Do not place ammable or explosive objects on or around the
gas hob, e.g. curtains.
The distance between the side walls and the back wall with
the edge of the gas hob should be at least 100mm and 50mm
respectively. Otherwise if there are ammable materials around
the gas hob, e.g. wooden wall and plastic wall etc, then the gas
hob should be installed at a distance of at least 150mm to the
side wall and 100mm to the back wall.
The distance between the hob to the ammable ceiling should
be 1m, otherwise there is no limit.
The use of the gas hob will result in temperature rising and
humidity increasing in the room where the hob is installed.
Therefore, please ensure there are good ventilation openings.
If the gas hob operates at a high ame for a long time , then
good ventilation is required. To accomplish this ventilation, you
may open a window, door, or use an efcient range hood with
an exhaust fan.
Installing the gas hob over other appliances such as oven,
steam oven and microwave etc should be according to the
requirements specied in the manufacturer’s manual to ensure
it meets the ventilation requirement.
If a drawer is installed under the hob, it is recommended to use
a non-ammable intermediate support to isolate the objects
stored in the drawer from circulating air coming from the hob’s
ventilation system. Please do not put any heat-sensitive or
ammable products under the drawers, which include spraying
agent or shoes polishing.
If the gas hob is installed in a cupboard, the plastic cooking
and adhesive bonded panel in it should be subjected to the
re-resistant glue treatment (heat resistant glue); otherwise,
deformation or scaling of the surface-layers will likely result,
especially on the sides of the cupboard.
The gas hob should be installed on a solid, at worktop. The
minimum thickness of the worktop should be 16mm and the
depth should be more than 600mm.
The cupboard should have a tapping size which meets the
ventilation requirements and is open to the air. The stove
ventilation pipe opening should be a minimum of 100cm2.
Otherwise, the lack of ventilation might cause an explosion
resulting from the leakage of gas.
Installation
9
Placement location
ER94331HK
ER94351HK
ER95351HK
measurements in mm
measurements in mm
measurements in mm

According to the Gas Safety Regulations of Hong Kong, any
gas installation works including the installation of appliances
and connection tubing, must be undertaken by registered
gas installers who are registered for that appropriate classes
and be employed by registered gas contractors.
Before installation, please carefully check the nameplate on
your gas hob. Make sure that the gas hob type specied on
the nameplate (which is stuck to the back shell) is consistent
with the gas that you are currently using. If you have any
doubts on whether the gas you are using is consistent,
please contact our Customer Care Hotlines.
Install a special gas valve between the indoor gas connecting
hose and the gas hob, in order to switch on and off the gas.
It should be installed in such a way that in the event an
accident occurs during operation period, the user will be able
to immediately shut of the gas. In addition, please ensure
this gas valve can be accessed at all times.
Please install the domestic range hood with an exhaust pipe
in accordance with the local gas hob installation specication
and guides. This type of range hood should have a distance
of at least 650mm to the gas hob.
The gas hob has already received a strict gas leakage
performance test before leaving the factory. Do not dismantle
the faceplate or inner parts during the installation of the gas
hob, to avoid later gas poisoning and re risk resulting from
the gas leakage during the operation.
Please ensure that when the installation is completed, the
gas hose connected to the gas hob does not touch any
movable object in the cupboard, e.g. drawer, roller etc.
Please conrm the ashboard are safe and grounded.
If you move house and intend to reinstall the gas hob to your
new house, please contact our Customer Care Hotlines.
Installation
10
Gas hob
Shutter
Gas hob
Shutter
Gas hob
Ventilation pipe

Please perform the tapping on the countertop according to
the tapping template (keeping to the installation size of all
the  ve types of products). To ensure the proper connection
of the gas hose, a space of at least 100mm height should be
kept available below the gas hob.
To ensure the stable placement of the gas hob, please
ensure that after the tapping, the vertical sides of the
installation site are smooth.
Follow the method shown in the illustration on the left and
clamp the four spring sheets supplied with the product to the
corresponding four installation positions on the back shell.
After installing the spring sheets, push the entire gas
hob  rmly into the cutout opening in the countertop, until
the outside rim of the gas hob is seated closely on the
countertop.
Installation
11
Countertop tapping

According to the Gas Safety Regulations of Hong Kong, any
gas installation works including the installation of appliances
and connection tubing, must be undertaken by registered
gas installers who are registered for that appropriate classes
and be employed by registered gas contractors.
The indoor gas hose behind the gas meter and the air inlet at
the bottom of the gas hob should be connected with a metal
bellows and a rubber hose approved by EMSD whose length
should not exceed 1.5m.
We recommend you to use the metal bellows to attach
the connecting hose. Especially, if the other appliances
are installed under the hob such as a disinfecting cabinet,
backing oven and microwave oven etc, a gas rubber hose
must not be used for the gas connection.
Using a gas rubber hose for the gas connection
-The multi-directional air inlet used for connecting the hose is
provided in the packing case of gas hob.
-The two ends of the gas hose are connected to the gas hob
and the indoor gas valve(the inside diameter of the gas hose
is 9.4mm).
-When connecting the gas hose, you must insert the gas
hose until it reaches the red line on the multi-directional air
inlet, and secure it firmly in position with a hose clip.
-After the connection is completed, please make sure that
the gas hose is not flattened, twisted or bent by any other
objects. Then smear soap suds all over the hose connection
part; and check each part of the connection hose carefully to
see if there is any leakage.
-We recommend that you perform an airtight test for the gas
hob periodically while it is in use, or else replace the gas
hose annually.
-Do not leave the gas hose in a high temperature area or put
it contact with any high temperature section of the gas hob.
Installation
Connect to gas pipeline
12
multi-directional air inlet
red line
hose clip

Leak detection
Attention !
After the gas pipeline connection has been completed, the
leak detection test must be performed by registered gas
installer who employed by registered gas contractor.
Smear the suds on each connection part with a soft brush,
and then open the gas valve to check carefully if bubbles
appear, please close the gas valve immediately, and adjust
the air inlet connection until no bubbles appear.
Connection electrical source
The electrical source is xed in the middle of bottom, when
you use it, please conrm it is safety and grounded.
Please conrm the hob wire are grounded, it is used
attached a tri-pins, and the tri-pins are grounded, when it is
creepage, the setting can prevent human from getting an
electric shock.
We suggest the ashboard is xed on the right underside, be
far away from the gas and air inlet.
Installation
13
Gas leak detection
Plug into socket
≈100mm
≈900mm
surface
size of tapping 880±2mm

As shown in the below picture, please make sure that the
knobs, burner heads, caps and supports have been installed
correctly. Incorrect installation will seriously affect the normal
use of the product and shorten its life-span.
When installing the supports and burners, the user should
pay attention that the protruding objects on the bottom of the
supports and burners are aligned with the stretching slot on
the faceplate, which is used for maintenance. If you place the
components randomly or rotate them for hob placement, the
stainless steel faceplate may be scratched. The appearance
damage of the gas hob resulting from such installation
operations is not covered by our warranty.
Installation
Pan supports,
caps and burners
14
Hole
Spark Plug
Thermocouple

Installation
15
ER94351HK
ER95351HK
ER94331HK

Top view of product
Back view of product
EasyFixTM spring sheet
Foam seal
Installation warning
Name plate
Gas burner operation
Getting familiar with your new hob
16
Double-ring cap
Double-ring cap
Double-ring cap
Wok trivet
Wok trivet
Wok trivet
Burner base
Burner base
Small support
Small support
Small support
Main support
Main support
Main support
Inner cap
Inner cap
Inner cap
Outer cap
Outer cap
Outer cap
Burner base
Burner base
Burner base
Knob
Knob
Knob
Top sheet
Top sheet
Top sheet
ER94351HK
ER95351HK
ER94331HK
Burner base
Knob
Top sheet

17
These instructions apply to several appliance models. It is
possible that individual features are described which do not
apply to your appliance.
It is essential to ensure that all the burner parts and the pan
supports are correctly installed for the appliance to work
correctly. Fig.1+2.
Please clean the hob and its accessories thoroughly. This
will remove the ‘new’ smell of the hob.
Before using, ensure the gas pipeline, knob, burner heads
and caps, and supports have been mounted correctly. Then,
open the indoor gas valve.
The rst ignition (or ignition after it has been left unused for a
long time) may be difcult, as there is residual air in the gas
pipeline, it may be difcult to light the burner. This is a normal
phenomenon. Please repeat the igniting operations, until the
hob has ignited properly.
To adjust the ame properly, refer to the following ve-stage
ame power indication chart and function descriptions. Select
your ame as desired.
Gas burner operation
Before rst use
Adjusting power
Fig.1
Fig.2
hole