Siemens SIMATIC ET 200SP User manual

___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
SIMATIC
ET 200SP
DQ 4x24..230VAC/2A ST digital
output module
(6ES7132-6FD00-0BB1)
Manual
03/2015
A5E32043575
-AB
Preface
Guide to documentation
1
Product overview
2
Wiring
3
Parameter
assignment/addressing
4
Interrupts/diagnostics alarms
5
Technical specifications
6
Parameter data record
A

Siemens AG
Division Digital Factory
Postfach 48 48
90026 NÜRNBERG
GERMANY
A5E32043575-AB
Ⓟ
12/2016 Subject to change
Copyright © Siemens AG 2014 - 2015.
All rights reserved
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by
personnel qualified
for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.

DQ 4x24..230VAC/2A ST digital output module (6ES7132-6FD00-0BB1)
4Manual, 03/2015, A5E32043575-AB
Preface
Purpose of the documentation
This manual supplements the system manual ET 200SP distributed I/O system
(http://support.automation.siemens.com/WW/view/en/58649293).
Functions that generally relate to the system are described in this manual.
The information provided in this manual and in the system/function manuals supports you in
commissioning the system.
Conventions
CPU: When the term "CPU" is used in this manual, it applies to the CPUs of the S7-1500
automation system as well as to the CPUs/interface modules of the ET 200SP distributed I/O
system.
STEP 7: In this documentation, "STEP 7" is used as a synonym for all versions of the
configuration and programming software "STEP 7 (TIA Portal)".
Please also observe notes marked as follows:
Note
A note contains important information on the product described in the documentation, o
n the
handling of the product or on the section of the documentation to which particular attention
should be paid.
Security information
Siemens provides products and solutions with industrial security functions that support the
secure operation of plants, solutions, machines, equipment and/or networks. They are
important components in a holistic industrial security concept. With this in mind, Siemens’
products and solutions undergo continuous development. Siemens recommends strongly
that you regularly check for product updates.
For the secure operation of Siemens products and solutions, it is necessary to take suitable
preventive action (e.g. cell protection concept) and integrate each component into a holistic,
state-of-the-art industrial security concept. Third-party products that may be in use should
also be considered. You can find more information about industrial security on the Internet
(http://www.siemens.com/industrialsecurity).
To stay informed about product updates as they occur, sign up for a product-specific
newsletter. You can find more information on the Internet
(http://support.automation.siemens.com).

DQ 4x24..230VAC/2A ST digital output module (6ES7132-6FD00-0BB1)
Manual, 03/2015, A5E32043575-AB 5
Table of contents
Preface ................................................................................................................................................... 4
1 Guide to documentation .......................................................................................................................... 6
2 Product overview .................................................................................................................................... 8
2.1 Properties..................................................................................................................................8
3 Wiring ................................................................................................................................................... 10
3.1 Wiring and block diagram .......................................................................................................10
4 Parameter assignment/addressing ........................................................................................................ 12
4.1 Parameters .............................................................................................................................12
4.2 Explanation of parameters ......................................................................................................13
4.3 Address space ........................................................................................................................14
5 Interrupts/diagnostics alarms................................................................................................................. 15
5.1 Status and fault displays .........................................................................................................15
5.2 Load voltage status.................................................................................................................17
5.3 Interrupts.................................................................................................................................17
5.4 Diagnostics alarms..................................................................................................................17
6 Technical specifications ........................................................................................................................ 18
6.1 Technical specifications ..........................................................................................................18
A Parameter data record .......................................................................................................................... 21
A.1 Parameter assignment and structure of parameter data record.............................................21

DQ 4x24..230VAC/2A ST digital output module (6ES7132-6FD00-0BB1)
6Manual, 03/2015, A5E32043575-AB
Guide to documentation
1
The documentation for the SIMATIC ET 200SP distributed I/O system is arranged into three
areas.
This arrangement enables you to access the specific content you require.
Basic information
The system manual describes in detail the configuration, installation, wiring and
commissioning of the SIMATIC ET 200SP. distributed I/O system. The STEP 7 online help
supports you in the configuration and programming.
Device information
Product manuals contain a compact description of the module-specific information, such as
properties, terminal diagrams, characteristics and technical specifications.
General information
The function manuals contain detailed descriptions on general topics regarding the SIMATIC
ET 200SP distributed I/O system, e.g. diagnostics, communication, Web server, designing
interference-free controllers.
You can download the documentation free of charge from the Internet
(http://w3.siemens.com/mcms/industrial-automation-systems-simatic/en/manual-
overview/tech-doc-et200/Pages/Default.aspx).
Changes and supplements to the manuals are documented in a Product Information.

Guide to documentation
DQ 4x24..230VAC/2A ST digital output module (6ES7132-6FD00-0BB1)
Manual, 03/2015, A5E32043575-AB 7
Manual Collection ET 200SP
The Manual Collection contains the complete documentation on the SIMATIC ET 200SP
distributed I/O system gathered together in one file.
You can find the Manual Collection on the Internet
(http://support.automation.siemens.com/WW/view/en/84133942).
My Documentation Manager
The My Documentation Manager is used to combine entire manuals or only parts of these to
your own manual.
You can export the manual as PDF file or in a format that can be edited later.
You can find the My Documentation Manager on the Internet
(http://support.industry.siemens.com/My/ww/en/documentation).
Application examples
Applications examples support you with various tools and examples for solving your
automation tasks. Solutions are shown in interplay with multiple components in the system -
separated from the focus in individual products.
You can find application examples on the Internet
(http://support.industry.siemens.com/cs/ww/en/ps/ae).
CAx Download Manager
The CAx Download Manager is used to access the current product data for your CAx or CAe
systems.
You configure your own download package with a few clicks.
In doing so you can select:
●Product images, 2D dimension drawings, 3D models, internal circuit diagrams, EPLAN
macro files
●Manuals, characteristics, operating manuals, certificates
●Product master data
You can find the CAx Download Manager on the Internet
(http://support.industry.siemens.com/my/ww/en/CAxOnline).
TIA Selection Tool
With the TIA Selection Tool, you can select, configure and order devices for Totally
Integrated Automation (TIA).
This tool is the successor of the SIMATIC Selection Tool and combines the known
configurators for automation technology into one tool.
With the TIA Selection Tool, you can generate a complete order list from your product
selection or product configuration.
You can find the TIA Selection Tool on the Internet
(http://w3.siemens.com/mcms/topics/en/simatic/tia-selection-tool).

DQ 4x24..230VAC/2A ST digital output module (6ES7132-6FD00-0BB1)
8Manual, 03/2015, A5E32043575-AB
Product overview
2
2.1
Properties
Article number
6ES7132-6FD00-0BB1
View of the module
①
Module type and name
⑦
Function class
②
LED for diagnostics
⑧
Color coding module type
③
2D matrix code
⑨
Function and firmware version
④
Wiring diagram
⑩
Color code for selecting the color identification labels
⑤
LEDs for channel status
⑪
Article number
⑥
LED for supply voltage
Figure 2-1 View of the DQ 4×24..230VAC/2A ST module

Product overview
2.1 Properties
DQ 4x24..230VAC/2A ST digital output module (6ES7132-6FD00-0BB1)
Manual, 03/2015, A5E32043575-AB 9
Properties
The module has the following technical properties:
●4 digital outputs each with a value status (quality information)
●Supply voltage L+
●Switches in zero point
●Output current 2 A per channel
●Total current 8 A (per module)
●Configurable substitute values (per channel)
●Suitable for solenoid valves, AC contactors, and indicator lights
The module supports the following functions:
●Firmware update
●Identification data I&M0 to I&M3
●Reconfiguration in RUN
●PROFIenergy
You can configure the module with STEP 7 (TIA Portal) and with a GSD file.
Accessories
The following accessories must be ordered separately:
●Labeling strips
●Color identification labels
●Reference identification label
You can find more information on accessories in the ET 200SP distributed I/O system
(http://support.automation.siemens.com/WW/view/en/58649293) system manual.

DQ 4x24..230VAC/2A ST digital output module (6ES7132-6FD00-0BB1)
10 Manual, 03/2015, A5E32043575-AB
Wiring
3
3.1
Wiring and block diagram
This section includes the block diagram of the DQ 4x24..230VAC/2A ST module with the
terminal assignments for 2-wire and 3-wire connection.
You can find information on wiring the BaseUnit in the ET 200SP distributed I/O system
system manual.
NOTICE
Dangerous voltage. Risk of death or serious injury.
Always disconnect the system and module from the power supply before commencing
work.
Note
Limiting overvoltage
You must ensure overvoltage is limited to 1
kV for the encoder supply.
Note
Power limitation
To limit power, each input voltage must have a fuse with a maximum rating of 10
A tripping
current. The fuse must be a quick
-acting microfuse.
Note
You may use and combine the different wiring options for all channels.