Signature S024 User manual

Instruction Manual
20LWater Boiler
S024
AC: 220V-240V~ 50Hz 1650W

Guarantee
This product is guaranteed for 12 months from the date of original purchased. If any defect arises
due to faulty materials of workmanship faulty products must be returned to place of purchases.
Refunds or replacement is at the discretion of the store.
The following conditions apply:
•The product must be returned to the retailer with original proof of purchases.
•The product must be installed and used in accordance with the instructions contained in this
instruction guide.
•It must be used only for domestic purpose.
•It does not cover wear and tear, damage, misuse or consumable parts.
•SVG has no responsibility for incidental or consequential loss or damage.
•Valid in the UK and Eire Only
Technical Specification
AC: 220V-240V~ 50Hz 1650W Link House, Bute Street,
Fenton, Stoke On Trent,
Staffordshire,ST4 3PR

Spare Parts Identification
1. Screw
2. Bottom fixer
3. Bottom plate
4. Power cord
5. Fixer
6. Heating element
7. Resettable thermostat
8. Screw
9. Screw
10. Keep warm plate
11. Auto thermostat
12. Screw
13. Inner pot down cover
14. ON/OFF switch
15. Yellow indication light
16. Red indication light
17. Screw
18. Handle
19. Handle starter
20. Housing
21. Screw
22. Upper cover
23. Handle
24. Screw
25. Water gauge fixed plate
26. Water gauge nut
27. Gasket
28. Water gauge jacket
29. Water gauge
30. Gasket
31. Key-press
32. Water faucet upper cover
33. Water faucet shaft
34. Spring
35. Water faucet core
36. Water faucet
37. Fixer screw
38. Water faucet sealed ring
39. Water faucet nut
40. Inner wiring
41. Buckle

Important Safeguards
When using electrical appliances, basic precautions should always be followed, including the
following:
1. Read all instructions.
2. Never immerse the appliance in water
3. Never switch on the appliance if there is no water in the tank
4. Always use the appliance on a dry, level and heat-resistant surface away from any edges
5. Ensure hands are dry before using the appliance
6. The outside of appliance gets very hot during use. Do not touch the surface
7. Do not remove the top cover while boiling.
8. If the appliance is overfilled, boiling water will spill out of the unit
9. The appliance produces boiling water – ensure the unit is out of reach of children.
Electrical safely
The wires in the mains lead are coloured in accordance with the following code:
GREEN/YELLOW: EARTH (E)
BLUE: NEUTRAL (N)
BROWN: LIVE (L)
As the colors of the wires in the mains lead of this appliance may not correspond with the coloured
markings identifying the terminals in your plug, proceed as follows:
The wire which is coloured GREEN & YELLOW must be connected to the terminal in the plug
which is marked with the letter “E” by the earth symbol or coloured GREEN,
GREEN/YELLOW.
The wire which is coloured BLUE must be connected to terminal which is marked with the letter
“N” or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal which is marked with the
letter “L” or coloured RED
Always ensure that the Mains Cord is located into the Plug through the Cord Guard or Cable
Clamp, (plug wiring diagram above), and that the Cord Guard screws are tightened to clamp the
Cord (outer sheath and inner coloured wires) into position in the Plug. Make sure that plug top is
also fitted securely.
This appliance must be protected by a 13 Amp fuse in a 13 Amp type (BS1363) plug. Should you
need to replace the fuse, use only a 13Amp ASTAapproved BS1363 fuse (13A).

OPERATION GUIDELINES
It is important to ensure the correct Plug Adaptor is used when operating in a country not using the
UK 13 Amp socket system. If in doubt, consult a qualified electrician.
Before using this Boiler
The appliance must be earthed installation:
1. Please read this instruction manual completely.
2. Before using the appliance, first clean the tank, top cover and body etc.
3. Place the unit upright on a firm and flat surface
4. Plug the appliance into an earthed socket while the unit is switched off.
How To Use This Boiler
•Fill the tank with cold water. There is a maximum level marked on the inside of the tank –
do not fill above this mark.
•Make sure the environmental temperature indoors is about 10-38 degrees and
environmental humidity is less than 90%
•Replace the cover and switch the unit on.
•The heating lamp indicator should now light up the unit will begin to boil the water.
•After about 35 minutes the water temperature will have reached 97 degrees and the
auto-thermostat switches the large heating element off and the small heating element on
which automatically keeps the water at the correct temperature.
•When about three cups of water are remaining in the tank, turn the unit off and unplug it
from the electric outlet.
Thermal cut-out
The appliance is fitted with a thermal cut-out. If this is activated, the unit will turn itself off.
Although the lamp will remain on, the unit must be unplugged before it can be reset. To reset the
appliance, wait until the appliance has cooled down. The reset button is located on the underside of
the appliance.
The safety device may have been switched off during transport, if so reset the thermal cut-off
following the above instructions.
If resetting this thermal cut-out does not switch the unit back on, place contact the manufacturer.

Cleaning
This unit must be cleaned thoroughly after each use. This is in addition to weekly cleaning using
vinegar to remove mineral deposits. If these deposits are not removed, pitting of the metal can occur
and may result in damage to the appliance.
Cleaning after use:
•Cleaning the tank, top cover and the body, etc. and dry them with a soft dry cloth. All these
parts are made of stainless steel and can be cleaned with a scouring agent.
•If the appliance is to function properly, the cavity in the middle of the base must be free of
lime scale. Use a scale remover if necessary.
•This heater includes an overheat protection system that turns off the heater when parts of the
unit are getting excessively hot.
•To clean the tap, move a brush up and down through the tap then insert the brush through
opening inside the appliance to clean the tap connection. Wash the tap handle in hot soapy
water and rinse. Replace the tap.
•Do not use baking soda to clean the appliance as it can discolor and pit the metal.
PROBLEM
Trouble Shooting
CAUSE REMEDY
The light is off,
the water is not heated. The unit is not connected to power cord
Check the switch, outlet,
fuse, cord and connect it
correctly.
The light is off, the water
is not heated.
The unit automatically shut-down
when it detects that there is no
water inside the boiler.
Simply press the reset
button underneath boiler
unit.
The light is off,
the water is heated.
1. The lights or resistance are
loose.
2. The lights or resistance broke
down.
Take it to an authorized
service center for repair.
The light is on, the water
is not heated. 1. The wire is loose. 2. Heater tube broke down. Take it to an authorized service center for repair.
The switch doesn't turn
into keep warm position
automatically.
The warm thermostat is
malfunctioning. Take it to an authorized service center for repair.

Disposal instructions for Signature items in accordance with the WEEE directive.
Disposal of Unit
Appliances bearing the symbol shown here may not be disposed of in domestic rubbish.
You are required to dispose of old electrical and electronic appliances like this
separately. Please visit www.recyclemore.co.uk, or www.recylcenow.co.uk for access
to information about the recycling of electrical items. The WEEE directive, introduced
in August 2006, states that all electrical items must be recycled, rather than taken to
landfill. Please arrange to take this appliance to your local Civic Amenity site for
recycling, once it has reached the end of its life.
Imported & Distributed throughout the U.K. By SVG Group ST4 3PR
www.signature-products.co.uk