Signtex Crystal CRR-REC Series Quick start guide
Series CRR-REC
Remote Edge-Lit Exit Sign
CrystalRecessed Mount
REV 02.09.2
for Universal Central Battery System Series CBS
MASTER
1. Disconnect AC power before servicing. 7. Do not let power cords touch hot surfaces.
2. Refer to wiring diagram for proper connections. 8. Mount and secure the fixture at a location and height
3. All servicing should be performed by qualified personnel. to avoid ready access and tampering by unauthorized
4. Consult your local building code for approved wiring and persons.
installation. 9. The use of accessory equipment is not recommended by
5. Do not use outdoors. the manufacturer and may cause an unsafe condition.
6. Do not use this equipment for other than intended use.
IMPORTANT SAFEGUARDS READ AND FOLLOW ALL SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
INSTALLATION INSTRUCTIONS AND OWNER'S MANUAL
Before installing or connecting any primary power wiring,
DISCONNECT MAIN POWER SUPPLY AT THE CIRCUIT BREAKER OR FUSE.
LAMP HOUSING
ASSEMBLY
PIGTAIL
CONNECTOR
ASSBY HOUSING
SCREW #8-32
2 SUPPLIED
24 VDC
INPUT
CIRCUIT
24 VDC
OUTPUT
CIRCUIT
W
WHITE
GREEN
W
G
G
R
R
B
B
WALL
LAMP PLUG
KEY
G- GREEN: COMMON GND: 24 VDC NEG
W- WHITE: EXITS AND CVRE: 12-24 VDC POS
R- RED: EMERGENCY: 24VDC POS
B- BLACK: SECURITY / NIGHT OPS: 24 VDC POS
ALL MODELS
EMERGENCY POWER RATING (EPR):
SINGLE FACE- 2 WATTS
DOUBLE FACE- 4 WATTS
WATERFALL LENS WALL MTSTANDARD WALL MT
24 VDC
INPUT
CIRCUIT
24 VDC
OUTPUT
CIRCUIT
W
WHITE
GREEN
W
G
G
R
R
B
B
WALL
POLARIZED CONNECTOR
TRIM PLATE
LAMP HOUSING
SCREWS
#6-32 4 REQD
TRIM PLATE
SCREWS #8-32
(2 SUPPLIED)
STANDARD WALL MOUNT
1. Install Recessed Back Box as required. Edge of box should be just below finished panel surface.
2. Connect 24VDC input/output circuit wiring as shown above, and connect the GREEN and WHITE
leads to the pigtail connector supplied.
3. Position the sign assembly over the back box and connect the polarized lamp plug. Secure the sign
assembly to back box with the two color-matched #8-32 screws supplied. Trim plate should be flush
with the panel surface.
WATERFALL LENS WALL MOUNT
1. Follow STANDARD WALL MOUNT steps 1-2.
2. Position the lamp housing and lens assembly over the back box and connect the polarized lamp
plug. Secure the lamp housing to the back box with four #6-32 screws supplied.
3. Slide Trim plate over lens carefully, until flush with panel surface, and secure with
two #8-32 color-matched screws supplied.
MASTER
-2-
Before installing or connecting any primary power wiring,
DISCONNECT MAIN POWER SUPPLY AT THE CIRCUIT BREAKER OR FUSE.
Series CRR-REC
Wall Mount
Installation
Remote Edge-Lit Exit Sign
CrystalRecessed Mount
for Universal Central Battery System Series CBS
REV 02.09.2
TOP MOUNT
KEY
G- GREEN: COMMON GND: 24 VDC NEG
W- WHITE: EXITS AND CVRE: 12-24 VDC POS
R- RED: EMERGENCY: 24VDC POS
B- BLACK: SECURITY / NIGHT OPS: 24 VDC POS
24 VDC
INPUT
CIRCUIT
24 VDC
OUTPUT
CIRCUIT
W
W
G
G
R
R
B
B
CEILING
PIGTAIL
CONNECTOR
TRIM PLATE
TRIM PLATE
SCREWS #8-32
(2 SUPPLIED)
LAMP HOUSING SCREWS
#6-32 4 REQD
LAMP PLUG
GREEN
WHITE
1. Follow STANDARD WALL MOUNT steps 1-2.
2. Position the lamp housing and lens
assembly below the back box and connect the
polarized lamp plug. Secure the lamp housing
to the back box with four #6-32 screws
supplied.
3. Slide Trim plate over lens carefully, until flush
with panel surface, and secure with two #8-32
color-matched screws supplied.
END MOUNT
KEY
G- GREEN: COMMON GND: 24 VDC NEG
W- WHITE: EXITS AND CVRE: 12-24 VDC POS
R- RED: EMERGENCY: 24VDC POS
B- BLACK: SECURITY / NIGHT OPS: 24 VDC POS
24 VDC
INPUT
CIRCUIT
24 VDC
OUTPUT
CIRCUIT
G
GREEN
WHITE
G
W
W
R
R
B
B
PIGTAIL
CONNECTOR
LAMP
PLUG
LAMP HOUSING
SCREWS #8-32 x 3/4"
(2 SUPPLIED)
WALL
TRIM PLATE
1. Follow STANDARD WALL
MOUNT steps 1-2.
2003529
R
T
E
E
T
K
N
I
L
I
D
S
E
T
CM
US
220VFWAvenu e,Grasonville,MD21638
TEL:(410)827--8300 Fax:(410)827-8866
[email protected] www.signtexinc.com
Signtex Inc
LIGHTING
