AmazonBasics B00MIBN16O User manual

AmazonBasics Desk Monitor Mount
B00MIBN16O

2
English . . . . . . . . . . . . . . . . . . . . . .3
Français . . . . . . . . . . . . . . . . . . . .17
Deutsch . . . . . . . . . . . . . . . . . . . .31
日本語 . . . . . . . . . . 45
中文. . . . . . . . . . . . . . . . . . . . 59
Italiano . . . . . . . . . . . . . . . . . . . . .72
Español. . . . . . . . . . . . . . . . . . . . .86

3
English
Instruction Manual · English
AmazonBasics Desk Monitor Mount
Contents
Make sure that the package contains the following parts:
Upper arm
(1 pc)
Bracket cover
(1 pc)
Grommet bracket
(1 pc)
M8 (1/4-20UNC, 3 inch)
(1 pc)
Wing nut
(1 pc)
Cable tie
(2 pcs)
M4 × 10 mm screw
(4 pcs)
Lower arm
(1 pc)
M4 × 10 mm knob
(4 pcs)
Base
(1 pc)
4 mm Allen wrench
(1 pc)
2.5 mm Allen wrench
(1 pc)
M3 x 6 mm
screw
1 (pc)

4
Supported monitor weights
Your monitor mount supports a monitor of the following weight:
Monitor adjustments
Your monitor mount lets you adjust the monitor viewing angle, height, tilt, and orientation
(portrait or landscape).
5 to 25 lbs
(2.3 to 11.3 kg)
lbs
kg
360°
180°
360° 13 in.
(330 mm)
70°
5°
Viewing angle Height Tilt Orientation

5
Assembly Instructions
Step 1: Choose a mounting option.
You can mount the monitor arm using the:
• Desk-clamp mount to attach your monitor arm to the edge of a tabletop. Go to
“Desk-clamp mount” on page 6.
• Plate mount to attach your monitor mount to an area that is away from the edge of a
tabletop. This mounting option requires a hole through the mounting surface. Go to
“Plate mount” on page 7.
Caution: Because mounting surface materials
can vary widely, make sure that the mounting
surface is strong enough to handle your monitor
mount and the monitor.

6
Desk-clamp mount
Step A: Determine the thickness of the mounting surface, then use the 4 mm Allen wrench to
adjust the location of the mounting clamp assembly, if necessary.
•Thetop screw holes on the clamp bracket fit a mounting surface thickness of less than
5/8 in. (1.6 cm).
•Themiddle screw holes on the clamp bracket fit a mounting surface thickness between
1/4 to 1 5/8 in. (0.6 to 4.1 cm).
•Thebottom screw holes on the clamp bracket fit a mounting surface thickness between
1 1/4 to 2 5/8 in (3.2 to 6.7 cm).
Step B: Slide the mounting clamp assembly onto the mounting surface, then tighten the
clamp.
Caution: Do not rotate the monitor past the
edge of desk. The weight of the monitor may
cause the desk to tip over.
<3/8 in. (1 cm) 1/2 to 1-3/8 in.
(1.2 to 3.56 cm) 1.5 to 2-3/8 in.
(3.7 to 6.0 cm)
4 mm Allen wrench

7
Plate mount
Step A: Remove the mounting clamp assembly from the clamp bracket on the base.
Step B: Remove the clamp bracket from the base. Keep the screws you remove. You will use
them later.
Step C: Make sure that the side of the grommet bracket with recessed screw holes is facing
down. Insert the M8 × 3 in. screw through the square hole in the center of the grommet
bracket.
Note: To keep the 3-inch screw from falling inside the base, temporarily attach the wing nut to
hold it in place.
4 mm
4 mm

8
Step D: Attach the grommet bracket to the base with the 3 screws you removed from the
clamp bracket.
Note: If the screws are not flush to the grommet bracket, the grommet bracket is upside down.
Remove these screws and the M8 × 3 in. screw, turn the grommet bracket over, then put all the
screws back in.
Step E: Remove the clamp plate from the clamp assembly using a Phillips screwdriver.
Step F: Center the base over the top of the hole in the mounting surface, then, from the
bottom of the mounting surface, slide the clamp plate you removed onto the M8 × 3 in. screw.
Secure the clamp plate to the screw with the wing nut.
Note: The M8 × 3 in. screw must be centered in the hole.
Caution: For secure arm attachment and to
avoid equipment damage, the base and the
clamp plate must make contact with the
mounting surface on both sides of the hole.
4 mm
0.31 to 2 in.
(8 to 51 mm)
< 2.25 in.
(57 mm)

9
Step 2: Determine the orientation of the monitor
You can mount the monitor in a locked portrait or landscape orientation, or you can leave the
monitor free to rotate 360°.
• If you want the monitor to rotate freely, do not insert the M3 x 6 mm screw.
• If you want the monitor in a locked orientation, insert the M3 x 6 mm screw into the front
of the plate on the upper arm.
Note: If you insert the screw, then want to change the monitor’s orientation after you mount the
monitor to the upper arm, you need to remove the monitor from the upper arm and insert or
remove the M3 x 6 mm screw.
Monitor rotates freely.
Monitor is locked in portrait or
landscape orienation.

10
Step 3: Attach the upper arm to the back of the monitor using a Phillips screwdriver.
Note: If a stand is attached to the monitor, remove the stand.
Note: You can use the M4 × 10 mm screws or M4 × 10 mm knobs to attach the arm to the
monitor.
Caution: The mounting screw holes on the
back of the monitor may require screws of a
different type or length than the provided
M4 × 10 mm screws or knobs.
• Using screws of that are too big in
diameter will damage the screw holes on
the monitor.
• Using screws that are too small or too
short may cause the monitor to fall off the
arm.
• Using screws that are too long may
damage the interior of the monitor.
Before you attach the monitor to the upper arm,
make sure that the provided screws or knobs fit
the screw holes on the back of the monitor.
If the provided screws or knobs do not fit, refer
to the documentation that came with the
monitor for the correct screw type and size.
Warning: The upper arm is under
tension and will move up rapidly, on its
own, as soon as the attached monitor is
removed. For this reason, remove the upper
arm, lay the monitor face down on a soft
surface, then remove the monitor. Failure to
follow this instruction may result in serious
personal injury or equipment damage.
M4 × 10 mm screws M4 × 10 mm knobsOR