Classic Exhibits visionary DESIGNS VK-1104 User manual

www.classicexhibits.com
Step 1
Page 1 of 3
866.652.2100
© 2013
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX -
VK-1104 - General Layout
10’
10’
Plan View

www.classicexhibits.com
Step 2
Page 2 of 3
866.652.2100
© 2013
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - General Setup Instructions
The Tool Typical Connection
Horizontal Inline Connection (remove only one setscrew)
Base Plate Connection Vertical Connection
(remove only two setscrews)
Most Visionary Designs exhibits can be
assembled with the supplied Hex Key Tool.
Occasionally, a flat head screwdriver may
be required.
Most horizontal extrusion connections have a patented expandable lock. This lock inserts into
the groove of an opposing extrusion. Tightening the lock with the Hex Key Tool expands the lock
and creates a strong positive connection.
Remove only (1) setscrew when disassembling. Replace setscrew in
extrusion after assembling it. Before packing, replace setscrew in
extrusion to avoid losing it.
Attach base plate to round or square
vertical extrusion using the bolt provided.
Be careful not to strip the threads.
When vertical extrusions are packed in
portable cases rather than crates or
tubs, they must broken down into
smaller sections which then require
assembly.
Remove only (2) setscrews when
disassembling. Replace setscrews in
extrusion after assembling it. Before
packing, replace setscrews in extrusion
to avoid losing them.
Using Your Setup Instructions
The Visionary Designs Setup Instructions are created specifically for your
configuration. They are laid out sequentially, including an exploded view of
the entire display, and then a logical series of detailed steps to assemble the
main structure and components. We encourage you to study the instructions
before attempting to assemble your exhibit.
Each page reminds you to tighten the setscrews after disassembling your
exhibit to prevent loss of the locks and setscrews (see below in RED).
This is VERY IMPORTANT.
Cleaning and Packing Your Display
1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only
non-abrasive cleaners.
2) When cleaning laminate inserts or countertops, use mild cleansers and a
soft material such as cotton.
3) Keep all display components away from extreme heat and long exposure
to sunlight to avoid warping and fading.
4) Retain all packing material. It will make re-packing much easier and will
reduce the likelihood of shipping damage.
Typical Connection (cont’d)
Numbered Label
Each extrusion contains a numbered label which
corresponds with setup instructions.
The label is located within a groove of the extrusion
(when possible). With Visionary Designs the labels
contain Black numbers unless otherwise specified.
Detail C EliateDDliateDDetail B
Detail A
Setscrews

www.classicexhibits.com
Step 1
Page 1 of 3
866.652.2100
© 2013
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - Backwall Assembly
1
1
4
5
4a
6a 6b
7a 7b
8a 8b
2a
3a
5a
2
3
Item
1
2/2a
3/3a
4/4a
5/5a
6a/6b
7a/7b
8a/8b
Description
Oval Base Plate
47.5”h Round Vertical Extrusion
47.5”h Round Vertical Extrusion
47.5”h Round Vertical Extrusion
47.5”h Round Vertical Extrusion
50.875” Curved Horizontal Extrusion
50.875” Curved Horizontal Extrusion
50.875” Curved Horizontal Extrusion
Quantity
2
1
1
1
1
1/1
1/1
1/1
Steps:
1) Connect vertical extrusions [3 and 5] to lower vertical extrusions [2 and 4].
2) Connect vertical assemblies [2/3 and 4/5] to oval base plates [1], refer to Detail D on
General Info. Page.
3) Assemble curved horizontals by connecting pieces [6a to 6b, 7a to 7b, 8a to 8b].
4) Connect lower curved assembly [6a/6b] between vertical assemblies [4/5 and 2/3] as shown
below.
5) Connect curved assemblies [7a/7b] between vertical assemblies [4/5 and 2/3].
7) Connect curved assemblies [8a/8b] between vertical assemblies [4/5 and 2/3].
Note: Attaching Graphics
Velcro the Graphics to the Top Front Edge of
the Upper Horizontals,
to the Bottom Front Edge of the Lower Horizontals
and along both sides

www.classicexhibits.com
Step 2
Page 2 of 3
866.652.2100
© 2013
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX -
Header and Literature Pockets Attachments
Attach connector piece to rack
as shown. Then connect
assembled literature
rack to connector extrusion.
Literature Rack Attachment
Tighten Lock
to Secure
Attach Oval Header to Hooks with Velcro, 1 on top center and 1 on bottom center.
Place hooks over backwall as shown.

www.classicexhibits.com
Step 3
Page 3 of 3
866.652.2100
© 2013
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX -
Pedestal Assembly
Floor
Insert Insert
Insert Door
Item
15
16
17
17A
18
19
20
21
22
Description
38”h Vertical Extrusion
38”h Vertical Extrusion
42”h Vertical Extrusion
Plate for Counter Connection
38”h Vertical Extrusion
20”w Horizontal Extrusion
8.5”w Horizontal Extrusion
20”w Horizontal Extrusion
8.5”w Horizontal Extrusion
Quantity
1
1
1
1
1
2
2
2
2
15
16
17
18
19
20
19
20
21
22
21
22
Steps:
1) Connect horizontal extrusions [19 and 20] between vertical extrusions
[15, 16, 17 and 18] at approximately 3.5” up from floor to bottom of metal.
2) Set floor in place atop lip of horizontal extrusions.
3) Place doors and inserts in place as shown.
4) Connect horizontal extrusions [21 and 22] between vertical extusions
[15, 16, 17 and 18] and atop inserts and door.
5) Velcro shelf supports to inside of pedestal, then set internal shelf atop supports.
6) Place counter atop assembled pedestal, attach [17A] to extrusion
[17] then connect smaller counter to [17A].
Plex Graphic Connection
Attach graphic using
Stand-off barrel and cap.
Extrusions 19 and
20 have a lip for
floor to rest
upon.
NOTE: TOP SIDE
Label needs to be
at top of round extrusion.
3A
17A
Internal Shelf
Slide pin into
hinge attached to
Round Vertical.
Slide Door hinge
atop pin.
Door
Hinge
Pin
Hinge
Door Attachment
Shelf
Support
Velcro
Strip
3.50”
3.50”