SIMPA SRJB72S User manual

香港煤氣適用
For Hong Kong Town Gas
嵌入式平面爐
Built-in Hob
: SRJB72S
SRJB73S
型號
Model
使用說明書
User Instructions

重要安全指示 …………………………………………………………………. 第頁
安裝指示……………………………………………………………………….. 第頁
操作指示 ………………………………………………………………………. 第頁
清潔及保養…………………………………………………………………….. 第頁
故障處理 ………………………………………………………………………. 第頁
規格 ……………………………………………………………………………… 第頁
注意!
根據香港氣體安全條例，任何氣體裝置工程，包括爐具和接駁喉管的安裝，
必須由註冊氣體裝置技工執行，而該技工已於相關的氣體工程類別註冊及受
聘於註冊氣體工程承辦商。
目錄
1
3
5
8
9
10

1
重要安全指示
以下指示對氣體爐具的安全操作十分重要，請詳細閱讀。如有查詢或需要維修服務，請致電煤氣公司24小
時客戶服務熱線2880 6988。
安裝
1. 使用認可印有機電工程署批准標記 (例如: 機電工程署批准 EMSD APPROVAL GTXXXX) 的氣體接駁喉管
連接爐具或使用機電工程署接納的其他恰當方法。
2. 必須安裝穩壓器(C002D-04000-2) ，並確定壓力設定為 1.0 千帕。
3. 當在櫥櫃面安裝嵌入式氣體煮食爐時，檢查面板進風口(如適用)沒有阻塞，以確保煮食爐在使用時操作
正常。
4. 爐具須安裝在空氣流通之房間內。
5. 不要將易燃物料、噴霧及壓縮容器置於爐具下方的廚櫃內。
使用
1. 當懷疑洩漏氣體時，將窗戶打開，以及關閉煤氣錶閥。切勿操作任何電器或電掣開關。切勿在現場使用
任何電話。在現場以外的地方，致電煤氣公司緊急事故熱線，電話：2880 6999。
2. 請參照說明書內指引正確使用爐具。
3. 爐具只供家用，切勿用於工商業用途。
4. 除煮食外，切勿使用爐具作其他用途，例如烘乾衣物。
5. 使用爐具前，請開啟窗戶及排氣系統。
6. 不可讓兒童使用爐具。
7. 切勿讓爐具在無人看管下運作。
8. 切勿在爐頭加上錫紙碟，這會引致燃燒問題。
9. 請確保爐頭蓋及爐頭身沒有變形，如有異常，請聯絡煤氣公司安排更換。
10. 使用前，確保爐頭蓋、爐頭身和爐架擺放正確，沒有傾斜。
11. 請確保爐頭火孔沒有被水或污漬堵塞。
12. 在一個爐架上，切勿放置超過10公斤的重量。
13. 爐架很重的，切勿掉下。
14. 不應按下點火旋鈕超過10秒。如爐頭於10秒後仍未燃點，等待最少1分鐘後，才再試燃點。
15. 請確保使用時火焰平均。
16. 注意爐面、爐頭及爐架的高溫。
17. 切勿使用直徑過大的平底煮食鍋具，避免溫度過高而造成燙傷及影響爐具的使用壽命。使用細小鍋具
時，請將火力調低，避免火焰超出鍋具底部。
爐頭 最大平底煮食鍋具直徑（毫米）
左爐頭 280
右爐頭 280

2
18. 請確保鍋具穩定地放在爐架上，如鍋具容易滑動，必須緊握它。
19. 面板是固定的，切勿移動。
20. 燒開水或煮湯時，注入的水量連湯料不可超過鍋具容量三分之二，溢出液體會影響燃燒和損壞爐具。
21. 使用小火時，不應急速打開爐具下方的廚櫃門，以免氣流弄熄爐火。
22. 烹調時，請盡量蓋上鍋具。而鍋具的手柄亦應轉向適當位置，避免受熱或碰撞。
23. 請勿在爐具附近使用噴霧產品。
24. 使用後，應將所有旋鈕設於關閉位置。
25. 經常清潔爐頭以保持火孔暢通，如滾瀉食物及汁液，應在爐具冷卻後儘快清潔爐頭。
保養
1. 定期檢查氣體喉管狀況，確保沒有紐結或裂縫，若發現損壞，請聯絡煤氣公司更換喉管。
2. 讓爐具完全冷卻後，才可進行清潔。
3. 進行清潔時，應穿上保護手套避免割傷。避免接觸爐具的內部位置。
4. 清洗爐頭蓋及爐頭身後，用乾布將爐頭蓋完全抹乾，爐頭火孔不可留有水份，以免影響燃燒。
5. 使用前和使用後，注意爐頭的狀況和清潔。以下不正常狀況會產生燃燒不良，進而引致爐具損壞。請確保
採取相應措施，糾正有關問題。
重要安全指示
不正常情況 處理措施
爐頭蓋及爐頭身變形 聯絡煤氣公司更換零件。
爐頭蓋及爐頭身傾斜 將爐頭蓋及爐頭身重新放好，不可傾斜。
爐頭火孔被水堵塞 用布將爐頭蓋及爐頭身抹乾後，重新放好。
爐頭火孔被污積或溢出物堵塞 用溫和清潔劑和刷子清潔爐頭蓋及爐頭身，用布抹乾後，重新放好。

3
安裝位置
安裝爐具
氣體接駁
安裝指示


703 403
600
最少 100
開孔尺寸：
寬703 x 深403 毫米
圖1
單位:毫米

4
安裝指示



爐頭放置
 中爐頭蓋的定位針應對準爐頭身定位槽。
爐架放置





芯火爐頭蓋傾斜
外環爐頭蓋傾斜
雙環爐頭
爐架錯誤放置
爐碟
爐頭座
芯火爐頭蓋
爐頭身
外環爐頭蓋
雙環爐頭
中爐頭
爐碟
爐頭座
爐頭身
爐頭蓋
爐架定位凹部
爐碟凸部
爐頭蓋傾斜
中爐頭
爐頭蓋
定位針
爐頭身定位槽

5
操作指示
爐具介紹
前方
❶爐架
❷芯火爐頭蓋
❸外環爐頭蓋
❹爐頭身
❺中爐架
❻中爐頭蓋
❼中爐頭身
❽旋鈕
❾強化玻璃面板
❿點火電極
⓫熄火安全裝置
⓬底盤
⓭電池盒(位於底部前方靠右位置)
⓮燃氣接口
❶❷
❸
❹
❺
❻
❼
❽
❾
❿
⓫
⓬
⓭
⓮
❿
⓫
SRJB72S SRJB73S
雙環爐頭
中爐頭

6
旋鈕及標示
左/右爐頭
中爐頭(SRJB73S)
操作指示

7
點燃爐頭
火力調節
爐頭點燃後，可按烹調所需轉動旋鈕調節火力。請緩慢調節火力。
關閉爐頭
操作指示



 在調較最大火力至接近中火時，若發現外環火焰不穩定(微弱或熄滅)，請立即調大火力，直至外
環火焰穩定，才繼續使用；或調小火力，使用芯火。



8
一般
清潔爐具
清潔及保養



9
故障處理

1. 電池已耗盡。 更換電池。
電池擺放錯誤。 正確裝上電池。
點火電極上有污垢或沾濕。 清理及抹乾點火電極。
2. 未開啟煤氣錶閥及／或爐具供氣閥。 完全開啟煤氣錶閥及／或爐具供氣閥。
喉管內含有空氣。 重複點火至喉管內空氣完全排出。
錫紙碟阻塞爐頭。 除去錫紙碟。
點火電極上有污垢或沾濕。 清理及抹乾點火電極。
3. 熄火安全裝置上有污垢。 清理熄火安全裝置。
未完全按下旋鈕或旋鈕沒有轉至點燃位
置。
按下旋鈕及轉至點燃位置。
4. 熄火安全裝置上有污垢。 清理熄火安全裝置。
爐火過弱被風吹熄，熄火安全裝置啟動。 旋鈕轉至關閉位置。等待 1分鐘，重新點火。
5. 爐頭蓋及爐頭身有污垢。 使用暖水及清潔劑清洗爐頭蓋及爐頭身。抹乾
後放好，重新點火。
6. 爐頭蓋及爐頭身變形。 聯繫煤氣公司更換零件。
爐頭蓋及爐頭身擺放不正確。 旋鈕轉至關閉位置。待爐具冷卻後，重新放好
爐頭蓋及爐頭身，並重新點火。
7. 為方便點燃爐頭，點燃火花會維持最多 5
秒。
屬正常，不需處理。
8. 爐頭蓋及爐頭身擺放不正確。 旋鈕轉至關閉位置。待爐具冷卻後，重新放好
爐頭蓋及爐頭身，並重新點火。
9. 殘留在爐頭內的氣體瞬間燃燒。 屬正常，不需處理。

10
規格
型號 SRJB72S SRJB73S
基本
規格
爐具類別 氣體煮食爐
安裝方式 嵌入式
氣體種類 香港煤氣
供氣壓力（千帕） 1.5
穩壓器出口壓力（千帕） 1.0
氣體接駁 ½吋英制陽螺紋
點火裝置 快易電子點火
爐頭數目 2 3
額定熱負荷
（千瓦）
左爐頭 5.5 5.5
右爐頭 5.5 5.5
中爐頭 / 2.85
總10.2 12.2
面板物料 搪瓷
面板厚度（毫米） /
爐具尺寸
－高 x 闊x 深
（毫米）
底盤至廚檯面 54 x 750 x 470
底盤至爐面 63 x 750 x 470
底盤至爐架 126 x 750 x 470
開孔尺寸－闊 x 深（毫米） 703 x 403
面板尺寸－闊 x 深（毫米） 750 x 470
重量（千克） 16.0 18.0
電源供應 1.5 伏特 C 型鹼性電池（1枚）
耗電量 （瓦） / /
安全
裝置
熄火安全裝置 熱電偶式
防高溫保護裝置 / /
連續煮食自動熄火功能 / /
功能 過熱熄火功能 / /
智慧功能 / /

Important Safety Instructions…………………………………………….. P.
Installation Instructions……………………………………………………... P.
Operation Instructions……………………………………………………….. P.
Cleaning and Maintenance………………………………………………... P.
Troubleshooting……………………………………………………………….... P.
Specifications……………………………………………………………………... P.
Contents
1
3
5
8
9
10
Attention!
According to the Gas Safety Ordinance of Hong Kong, any gas installation works
including the installation of appliances and connection tubing, must be undertak-
en by registered gas installers who are registered for those appropriate classes
and be employed by registered gas contractor.

1
The following instructions are very important to safe operation of gas appliance. Please read through them
carefully. Please contact Towngas Company on 24-hour customers service hotline [phone] for enquiry and
services.
Installation
1. Use approved gas tubing bearing EMSD approval marking (such as: 機電工程署批准 EMSD APPROVAL
GTXXXX) for connection to appliance, or other appropriate methods accepted by EMSD.
2. Fix the gas governor (C002D-04000-2). Ensure that the pressure setting is 1.0kPa.
3. When installing gas appliance on top of kitchen cabinet, check that the air-intake opening at top plate (if
applicable) is not blocked in order to ensure proper operation of the gas appliance.
4. Install the appliance in a well-ventilated room.
5. Do not store any flammable materials, sprays or pressurized containers inside the kitchen below appliance.
Operation
1. In case of suspected gas leak, open windows and shut off gas meter valve. Do not operate any electric
appliances or switches. Do not use any phones on site. Contact Towngas Emergency Hotline on 2880 6999
with a phone outside the premises.
2. Please use the appliance properly according to the operating instructions.
3. This appliance is designed for domestic use only. Do not use it for commercial purposes.
4. Do not use the appliance for any purposes other than cooking, e.g. drying clothes.
5. Open windows and turn on ventilation system before operating the appliance.
6. Do not allow kids to use appliance.
7. Do not leave operating appliance unattended.
8. Do not add aluminum discs to burners. This will incur combustion problem.
9. Ensure that burner cap and burner body are not deformed. Contact Towngas Company to replace the parts
if deformation is found.
10. Before use, ensure the burner cap, burner body and pan supports are in correct position and are not tilted.
11. Ensure that flame holes of burners are free from water and dirt.
12. Do not put weight exceeding 10kg on each pan support.
13. Pan support is heavy. Do not drop it.
14. Do not press the rotary knob for more than 10 seconds. If the burner is not ignited after 10 seconds, wait at
least 1 minute before making further attempt.
15. Make sure that flame condition is uniform during operation.
16. Heed high temperature of top plate, burners and pan supports.
17. Do not use flat bottom cooking utensil with too large diameter to avoid the risk of scald by high
temperature and reduce the service life of the appliances. When using small utensil, reduce flame power
that flame does not escape from utensil bottom.
Important Safety Instructions
Burner Maximum Diameter of
Flat Bottom Utensil (mm)
Left Burner 280
Right Burner 280

2
18. Ensure stability of utensil resting on pan support. Hold utensil firmly if it slips easily.
19. Top plate is fixed. Do not remove it.
20. Do not fill water including soup ingredients over two-thirds of utensil volume when boiling water or soup.
Spilled liquid of boiling will affect combustion and damage the appliance.
21. When the appliance is operating at low flame, do not open underneath cabinet door rapidly; otherwise,
flame may be extinguished by air draught.
22. Always use cooking utensils with a cover and make sure that the handles of the cooking utensils are
correctly positioned to avoid heating and collision of handles.
23. Do not use sprays near the appliance.
24. All knobs should be turned to off position after use.
25. Clean the burner frequently to maintain a clear gas passage of flame holes. Clean and tidy up the burner
after spillage of food and liquid once the appliance cools down.
Maintenance
1. Check condition of gas hose regularly. Ensure that it is free from kink or crack. Contact Towngas Company
to replace it if damage is found.
2. Allow the appliance to cool down completely before cleaning.
3. Wear glove to protect the hands from cut injury when cleaning the appliance. Do not touch any internal
parts of the appliance.
4. Dry burner cap and burner body completely with dry cloth after washing. Flame holes of burner must be
free from water lest combustion is affected.
5. Before and after use, notice the condition and cleanliness of burner. The following abnormal conditions will
incur abnormal combustion and thus damage of the appliance. Ensure undertaking measures to rectify the
problem accordingly.
Important Safety Instructions
Abnormal Condition Handling Measure
Burner cap and burner body
are deformed
Contact Towngas Company to replace the parts.
Burner cap and burner body
are tilted
Replace burner cap and burner body properly. Burner cap and
burner body must not be tilted.
Burner flame holes are blocked
by water
Dry burner cap and burner body with cloth and replace them
properly.
Burner flame holes are blocked
by dirt or cooking spillage
Clean burners with mild detergent and brush. Ensure that burners
are wiped dry before replacing them.

3
Installation Position
Install the appliance in a well-ventilated room, but do not install at
the position of strong wind. Keep it away from any flammable
objects (such as paper, oil), combustible, sprays or pressurized
containers. The appliance should be installed with a distance of
more than 150mm away from surrounding combustible materials.
Allow 650mm or more clearance above appliance. Install a range-
hood at a distance of not less than 650mm from the surface of
pan support of appliance. If the range-hood requires a different
installation distance, adopt the larger value. The combustion
products of appliance shall be evacuated by means of range-
hood.
The appliance can be installed in cut-out dimension.
 Cut-out dimension : W703 x D403 mm
If another appliance (e.g. dishwasher, washer) is to be installed under the gas appliance, keep a clearance of at
least 10mm from the bottom of the appliance. If the installation instructions of the appliance underneath
require a different distance, adopt the larger value. If an airflow generating appliance or device (such as built-in
oven, clothes dryer) is to be installed under the built-in gas appliance, a partition shelf must be added and
sealed with silicone gel. This prevents air draught affecting the appliance operation.
Appliance Installation
Position the appliance onto the bench-top opening. Secure the base tray with screw. Sealing gasket should be
affixed around the entire periphery of top plate bottom. Position the top plate properly onto the bench-top.
Then put the rotary knobs in correct position.
Gas Connection
Connect the gas appliance to the gas supply according to the prescribed standards in force and ensure that the
appliance matches with the type of gas supply. Furthermore, check that the supply pressure is 1.5 kPa and
governor pressure is 1.0 kPa.
Installation of Battery
Before use, the battery must be installed correctly. Appliance does not operate if batteries are placed wrongly.
Installation Instructions


703 403
600
Min. 100
Cut-out dimension ：
W703 x D403 mm
Fig.1
Unit: mm

4
Placement of Burner
Make sure that the following parts are fitted properly before use.
 Double-ring burner is composed of outer ring flame burner cap,
simmer flame burner cap and burner body.
 Middle burner is composed of burner cap and burner body.
 Place the burner caps and body onto the burner base without tilting.
 Locating pins of middle burner cap should be matched with the
notches of burner body.
Placement of Pan Support
Make sure that the following parts are fitted properly before use.
 Place the pan support in position horizontally with the depression fit
to the projection of drip pan.
Installation Instructions






Tilted simmer
burner cap
Tilted outer ring
burner cap

Tilted burner cap
Double-ring Burner Middle Burner
Improper placement of pan support
Drip pan
Burner base
Simmer
burner cap
Burner body
Outer ring
burner cap
Double-ring Burner
Middle Burner
Drip pan
Burner base
Burner body
Burner cap
Pan support de-
pression
Drip pan projecon
Burner cap
locating pin
Burner cap
locating notch

5
Appliance Descriptions
Installation Instructions
Front
❶Pan support
❷Simmer burner cap
❸Outer ring burner cap
❹Burner body
❺Middle pan support
❻Middle burner cap
❼Middle burner body
❽Rotary knob
❾Top plate
❿Ignition electrode
⓫Flame failure safety device
⓬Base tray
⓭Battery box (located at right-
front corner of bottom position)
⓮Gas Connection
❿
⓫
⓬
⓭
⓮
❿
⓫
Double-ring burner
Middle burner
❶❷
❸
❹
❺
❻
❼
❽
❾
SRJB72S SRJB73S