Simpex Electronic SRP-2309-100-RGBW-24V User manual

1 Änderungen vorbehalten. Angaben ohne Gewähr. / 26.09.2019 © Simpex Electronic
SRP-2309-100-RGBW-24V
100W DALI DT8 DIMMABLE LED DRIVER
Product Features
• DT8 Dimmable 4-Channel RGBW LED driver
• 100-240VAC wide input voltage
• 4-channels DC24V constant voltage output
• Built-in DALI interface, DALI DT8 device, each dvice is controlled via a single DALI address
• Color control according to DALI specicaons of device type 8
• Complies to DALI Standards IEC 62386-209-:2011
• Compable with universal DALI masters that supports DT8 commands
• Compable with AC-Push dimmer
• Compabel with DT6 DALI commands
• IP20 rang, suitable for indoor LED lighng applicaons

2 Änderungen vorbehalten. Angaben ohne Gewähr. / 26.09.2019 © Simpex Electronic
Technical data
INPUT
Voltage Range 100-240VAC
Frequency Range 50/60Hz
Power Factor (typ.) >0.9@230VAC
Total Harmonic Distoron THD ≤ 15% (@ full load /230VAC)
Eciency typ. 90% @ 230VAC full load
AC Current (typ) 1.2A @ 100VAC, 0.5A @ 230VAC
Inrush Current (typ) Cold start max. 50A@230VAC
Leakage Current < 0.5mA/230VAC
Stand by Power Consumpon 1W
OUTPUT
LED Channel 4
DC Voltage 24VDC
Voltage Tolerance +/- 1%
Max. Current max. 4.1A/CH, CH1+CH2+CH3+CH4 = 4.1A
Rated Power max. 98.4W
PROTECTION Short Circuit Yes, recovers automacally aer fault condion is removed
Over Temperature Yes, recovers automacally aer fault condion is removed
CONTROL
Dimming Interface DALI DT8
Dimming Range 0.1% - 100% for color sengs
1%-100% for brightness sengs (DT6, AC Push)
Dimming Methode PWM, 1.5kHz
Dimming Curve Logarithmic
ENVIRONMENT
Working Tempetrature -20°C - + 45°C
Max. Case Temperature 75°C
Working Humidity 10%-95% RH non-condensing
Storage Temperature -40°C - +80°C
Storage Humidity 10% - 95% RH
IP Rang IP20 (suitable for indoor LED lighng applicaons)
Safety & EMC
Safety Standards TUV EN61347-1, EN61347-2-13 approved
DALI Standards Comply with IEC 62386-209:2011
Withstand Voltage I/P-O/P: 3.75KVAC
Isolaon Resistance I/P-O/P: 100M Ohms / 500VDC / 25°C / 70% RH
EMC Emission EN55015, EN61000-3-2, EN61000-3-3
EMC Immunity
EN61547, EN61000-4-2,3,4,5,6,8,11, , surge immunity Line-
Line 1KV
Others
MTBF 193.6K hrs min. @ 230VAC full load and 25°C ambient tempe-
rature
Dimension 244 x 64 x 32mm
Warranty 5 years

3 Änderungen vorbehalten. Angaben ohne Gewähr. / 26.09.2019 © Simpex Electronic
Product dimension
Wiring diagram
Wiring diagram with DALI DT8
Wiring diagram with AC Push
Wiring diagram with DALI

4 Änderungen vorbehalten. Angaben ohne Gewähr. / 26.09.2019 © Simpex Electronic
Installaon
Operaon
SAFETY AND WARNINGS
• Do not install with power applied to the device
• Do not expose the device to moisture
• Do never connect two minuses (by example –R & -B) connect to the same potenal (same minus at the
module)
• Approved wire diameter: AWG16—AWG20 / 0.5mm2-1.5mm2
6-7mm isolated
Set DALI address manually via buons
1. Press and hold down any of the two buons unl numeric digital display ashes, then release the
buon.
2. 1.2. Click any of the two buons once to select a digit, click again to change the digit unl the desi-
red DALI address appears. Click rst buon to set “tens” posion and second buon to set “units”
posion. The address can be set from 00~63.
3. Then press and hold down any of the 2 buons unl the numeric digital display stops ashing to
conrm the seng.
Note: DALI address can be manually assigned from 00-63-FF, by factory defaults, no DALI address is assig-
ned for the dimmer, and the dispaly shows FF. Seng DALI address as FF will reset the dimmer to factory
defaultes
DALI address assigned by DALI masters
DALI address can also be assigned by DALI Master controller automacally, please refer to user manuals of
compable DALI Masters for specic operaons.
Note: The digital display will show AU. When the DALI master is assigning addresses.
Once an address is selected, all four channels' address will be the same. For example, if the dimmer is
addressed to 22 on the display then CH1, CH2, CH3 and CH4 will be the same address

5 Änderungen vorbehalten. Angaben ohne Gewähr. / 26.09.2019 © Simpex Electronic
Important Informaon
Drivers with PWM dimming might cause noises due to vibraon in the driver itself or resoncance frequencies of
other products.
Standard DALI preseng: 100% brightness for all 4 channels
CASE A Powersupply went to overload protecon mode
What happens ?
The strips start to blink. You are able to reduce the brightness with the soware and the strips will stop with blinking. You
can‘t controll the colors any more.
What can I do to go back to solve the problem?
A. 1. Reduce the load accoring to the specicaon.
2. Dissconnect the powersupply from AC for at least 10 min. Aer 10 min. it will go back to the factory sengs
3. You are now able to control the device again.
B 1. Dissconnect the load.
2. Dissconnect the powersupply from AC for at least 10 min. Aer 10 min. it will go back to the factory sengs
3. Connect the powersupply to AC
4. Connect the powersupply with your DALI soware.
5. Reduce Power On level and the max level. The level has to be under the max. load of the powersupply.
6. Switch the powersupply o and connect again the load.
7. You are now able to control all other parameter of the device.
Note: Simpex is just responsible for the product itself and not for consequential damages or costs. Extended
warranty requirements have to be agreed case by case. The general terms and conditions of the Simpex
Electronic AG apply (hps://www.simpex.ch/en/Imprint/) .