Simplicity 204 User manual

10” HEAVY
DUTY PLOW
NOTE: REPOSITION BEAM END TO THESE HOLES, WHEN
USING PLOW WITH 2-WHEEL TRACTORS.
,~fgM ’
the plow is used H rith the “725”,
move the Beam End to the center of the
Plow Beam Assembly after moving the
Spacer(“A”) to outside of Beam Assem-
b/y, opposite of Spacer “B”
MODEL 725 RIDING TRACTOR LANDLORD RIDING TRACTOR
ASSEMBLY AND ADJUSTMENT
( REQUIRES #203 HITCH ADAPTER )
1. Remove varnish from moldboard and share, using
a good grade of varnish remover. (Keep greased when
not in use. )
CAUTION: Be sure that the rolling, coulter is out of
the ground when the tractor is in reverse gear.
2. Bolt standard ( 1
) to plow bottom ( 2 ) .
3. Bolt beam ( 3 ) to standard at ( 4 ) . Lock with jam
nut so that beam is free to swing on standard.
4. Attach depth regulating yoke rod assembly ( 5 ).
Pin and cotter pin.
6. Attach the lift pin and chain assembly ( 9 ) to the
beam at
( 8 ) by means of the pin and spring clip pro-
vided. The hitch clevis adapter ( 10 ) is then attach-
ed to the tractor hitch by means of the pivot pin.
Connect the plow to the hitch adapter with the hitch
pin and insert the lift pin ( 9 ) In the tractor rear lift
assembly and secure in place with a pin and s,pring
clip.
5. Attach rolling coulter assembly
( 6 ) and adjust
coulter standard ( 7 ) so that blade runs approximately 7. Wheel weights should be used when operating the
l/2” to the left of landslide. Set the rolling coulter 10” Plow. The weights are designed so that as many
for best depth depending upon the soil. weights as necessary may be added to the wheels
Lie,. in USA
S,MPL,C,TY MANUFACTURING COMPANY, INC.

PLOW BOLT 704006
NUT 717006
704007 PLOW BOLT
r Order by Part Number
Reference Part Description
Letter NO.
A 112065 Share
B 1?2044 Standard
C 112077
Beam Assembly, Plow
D 11204: Yoke Rod Pssembly
E
112050
Yoke, L.H.
F
112051
Yoke, R.H.
G
112052 Pin, Yoke
H
722006
Pin, Cotter, w/extended prong, l/S” dia. x 1” lg.
1
112053 End Assembly, Flow Beam
K 715036
Capscrew, Hex Hd., 3/W-16 x 2-l/4” lg.
L 720002 Washer, Lock, 3/S”
.M 717003 N”t, Full Hex., 3/S”-16 NC
v112057 Standard, Coulter
J
8271023 Clamp
39201073 Nut, Special, S/16” x1”~ 2 l/4” lg.
:2 713004 Set Screw, Cup Point, Sq. Hd., 3/S”-16 NC x 1” lg.
112040 Coulter Assembly, w/bushing
‘P
112058 Spindle, Coulter
I:
‘?6!055 Washer
v 717018 Nut, Hex, ,am, 5/E"-11NC
'iv 705046
Screw, Cap, Hex., l/Z”-13 NC x1 3/4” lg.
.x 717006 Nut, Hex., Full, l/Z”-13 NC
T112068 Moldboard
7.
112069 Brace, Moldboard
ha
112066 Saddle
Aa
112067 Landside
AC 112070 Angle, Slip Heel
-a
112076
spacer, Plow Beam
AE 8111050 Bushing, Coulter