Simply Elegant 220-101 User manual

220-101
220-102
220-109
Retractable Screen
www.simplyelegantproducts.com 1
Outswing French Doors, Full Size and Retro Size (Full Size 6/0 can be cut to fit 5/4 and 5/0; Retro Size 6/0 can be cut to fit 5/10, 5/4 and 5/0)
INSTRUCTIONS (Page 1 of 4)
RETRACTABLE SCREEN ASSEMBLY AND INSTALLATION INSTRUCTIONS
PART REVIEW AND CHECK
Step 1: Verify that the following components are
included in the box. See No. 1a. Parts are listed from top
to bottom. See No. 1.
• Screen Housing marked A and D
• Screen Housing marked B and C
• Screen Track with white locking hardware in center
• Screen Track with black locking hardware in center
• Two Screen Track Covers
• Mounting screws for track
TOOLS REQUIRED
• Level
• Square
• Tape measure
• Screwdriver: at head and Phillips head
• Pencil
• Hacksaw
LAYOUT
Step 2: Remove all of the above items from the box and
place on the oor in front of the French door where the
double screen is to be installed.
The screen housings and tracks should line up with their
corresponding letters in a clockwise fashion, as indicated
below: A to A, B to B, C to C and D to D. See No.2.
No. 1 No. 1A
No. 1B
No. 2
A to A B to B
D to D C to C

220-101
220-102
220-109
Retractable Screen
www.simplyelegantproducts.com 2
Outswing French Doors, Full Size and Retro Size (Full Size 6/0 can be cut to fit 5/4 and 5/0; Retro Size 6/0 can be cut to fit 5/10, 5/4 and 5/0)
INSTRUCTIONS (Page 2 of 4)
RETRACTABLE SCREEN ASSEMBLY AND INSTALLATION INSTRUCTIONS
ASSEMBLY PREPARATIONS
Step 3: Very important! Please examine the picture at
right for additional details, see No. 3. Before snapping
the header and sill screen tracks into the screen
housings, please look at the backside of both the header
and sill screen tracks.
There you will nd a clear removable tape with the
numbers 6/0, 5/10, 5/4 and 5/0 on each end of the
track. These numbers correspond to the door unit size
that the screen will t onto.
Depending on the size door unit this system is being
installed on, you may need to cut both ends on the line
that corresponds with your door unit size, except for 6/0
sizes where no cutting is necessary.
Since this is a double retractable French door screen you
will need to cut both ends so that each retractable door
screen meets in the center of the door.
Note: If you only cut one end of the track,
the center will be off!
ASSEMBLY
Step 4: Once the sill and header screen tracks have been
cut to the appropriate size, slide each screen track into
each screen housing until they snap in place. See No. 4.
Lock in clockwise fashion as indicated below: A to A,
B to B, C to C and D to D. The screen frame unit is now
assembled and ready for mounting to the door unit.
No. 3
No. 4
A to A B to B
D to D C to C

220-101
220-102
220-109
Retractable Screen
www.simplyelegantproducts.com 3
Outswing French Doors, Full Size and Retro Size (Full Size 6/0 can be cut to fit 5/4 and 5/0; Retro Size 6/0 can be cut to fit 5/10, 5/4 and 5/0)
INSTRUCTIONS (Page 3 of 4)
RETRACTABLE SCREEN ASSEMBLY AND INSTALLATION INSTRUCTIONS
INSTALLATION
Step 5: Remove all trim molding from the interior side
of the frame (if present) and all sill molding (see No. 5)
from the French door frame before installing the double
retractable screen.
Removing the sill molding will require a at screwdriver
so that you can pry the molding from the door sill.
Now move the assembled screen unit up and center it
on the door unit, see No. 5A.
The inside edge of the screen housing should be ush
with the inside of the door frame. The sill track should
be positioned at least 1/8” below the top of the door sill,
see No. 5B.
Step 6: After positioning the screen frame unit on the
French door unit and making sure the two screens meet
up in the center correctly with the door, screw the head
track into the door frame. Screw in only two of the four
screws because you may need to adjust the position of
the screen unit to make sure that the screen is square
and level, see No. 6.
Step 7: Check again to make sure the screen sill track is
below the door sill by at least 1/8”. See No. 5B. Once this
is done, check again to make sure the screen is square
and level, if not adjust.
Now screw the screen sill track to the door sill. See No. 7.
No. 5 No. 5A
No. 5B
No. 6
No. 7

220-101
220-102
220-109
Retractable Screen
www.simplyelegantproducts.com 4
Outswing French Doors, Full Size and Retro Size (Full Size 6/0 can be cut to fit 5/4 and 5/0; Retro Size 6/0 can be cut to fit 5/10, 5/4 and 5/0)
INSTRUCTIONS (Page 4 of 4)
RETRACTABLE SCREEN ASSEMBLY AND INSTALLATION INSTRUCTIONS
INSTALLATION
Step 8: Test the screen door unit to see if the screen
meets correctly in the center.
If there is some trouble with the screen door sliding
and/or locking into place, you may need to check again
that the screen frame is level and square.
If needed, you can adjust the screen tension with
a Phillips head screwdriver at the end of the screen
housing. By pushing in and turning clockwise you
increase the tension or by turning counter-clockwise you
lower the tension. See No. 8.
Caution: The spring is under tension. Hold the
screwdriver tightly while adjusting!!!
Step 9: After making adjustments, add the rest of the
screws to the head track.
Step 10: Before you add the screen head and sill covers,
the head and sill screen covers may need to be cut to t
the correct width of your door unit like the screen head
and sill tracks.
Use a hacksaw to cut the end of the screen cover where
the cut line indicator tape is located. See No. 9.
After cutting, remove the remaining tape, snap the
screen covers over the top of both screen tracks. See No.
10.
Your retractable screen installation is now complete!
No. 8
No. 9
No. 10