Sirocco Fire Royal 1000 User manual

“Fire Royal”
Models 1000 & 600
DECORATIVE FUEL EFFECT APPLIANCE, THIS IS A
NATURAL GAS (G20) APPLIANCE FOR USE IN GB AND IE
ONLY AT A SUPPLY PRESSURE OF 20mbar.
USER’S, INSTALLATION
AND SERVICE MANUAL REMOTE
PLEASE KEEP THESE INSTRUCTIONS IN A SAFE
PLACE FOR FUTURE REFERENCE
Our policy is constant development and improvement.
Strict accuracy of illustrations and specifications is not guaranteed.
Modifications to design and materials may be necessary subsequent to
publication.
WINTHER BROWNE
75 Bilton Way, Enfield, London, EN3 7ER
Tel.[phone] Fax [phone]
V-11-07
eco

2
TABLE OF CONTENTS
IMPORTANT NOTES___________________________________________ 3
USER’S SECTION_____________________________________________ 4
FUEL EFFECT ________________________________________________ 4
GAS CONSUMPTION __________________________________________ 4
OPERATING INSTRUCTIONS -__________________________________ 4
MANUAL VERSION _______________________________________________ 4
TO LIGHT THE FIRE _________________________________________________4
SELECT THE BURNER FLAME LEVEL _________________________________4
TO TURN OFF_______________________________________________________4
CLEANING _________________________________________________________4
OPERATING INSTRUCTIONS - REMOTE CONTROL VERSION___________ 5
TO LIGHT THE FIRE _________________________________________________5
TO SELECT THE REQUIRED FLAME LEVEL ____________________________5
TO TURN OFF_______________________________________________________5
OXYGEN DEPLETION SYSTEM__________________________________ 5
FUEL BED ASSEMBLY _________________________________________ 5
INSTALLATION SECTION ______________________________________ 6
1 GENERAL DATA__________________________________________ 6
2 GENERAL INSTALLATION REQUIREMENTS ___________________ 6
3 CHECK CARTON CONTENTS _______________________________ 7
4 THE FIREPLACE _________________________________________ 7
5 GAS SUPPLY PIPE________________________________________ 7
6 APPLIANCE INSTALLATION ________________________________ 7
6.5 CHECK FOR GAS SOUNDNESS _____________________________ 8
6.6 FUEL BED ASSEMBLY_____________________________________ 8
7 FUNCTIONAL CHECKS ____________________________________ 8
8 CHECK FOR SPILLAGE ____________________________________ 8
9 FINAL CHECK AND CUSTOMER BREIFING ____________________ 9
10 SERVICING______________________________________________ 9
10.1 TO REMOVE THE BURNER UNIT ____________________________ 9
10.2 TO REMOVE THE PILOT BURNER ASSEMBLY ________________ 10
10.3 TO REMOVE THE GAS TAP / FSD / IGNITION UNIT ____________ 10
11 MAINTENANCE SPARES __________________________________ 10
12 FAULT FINDING _________________________________________ 10
V-11-07

3
IMPORTANT NOTES
1. SOFT WALL COVERINGS, (e.g. EMBOSSED
VINYLS etc.) WHICH HAVE A RAISED
PATTERN, ARE EASILY AFFECTED BY HEAT
AND MAY SCORCH OR BECOME
DISCOLOURED WHEN CLOSE TO A
HEATING APPLIANCE. PLEASE BEAR THIS
IN MIND WHEN RE-DECORATING.
2. AS WITH ANY GAS FIRE, THIS APPLIANCE
MUST BE INSTALLED BY A COMPETENT
PERSON (e.g. IN GB A C.O.R.G.I. MEMBER)
IN ACCORDANCE WITH THE INSTALLATION
INSTRUCTIONS AND THE LATEST EDITION
OF THE GAS SAFETY (INSTALLATION AND
USE) REGULATIONS OR THE RULES IN
FORCE.
3. IF THE FIRE IS INTENDED TO BE
INSTALLED TO A FIREPLACE THAT WAS
PREVIOUSLY USED FOR BURNING SOLID
FUELS THE CHIMNEY MUST BE SWEPT
PRIOR TO INSTALLATION.
4. THE FIRE MUST NOT BE INSTALLED
DIRECTLY ONTO CARPETS OR OTHER
COMBUSTIBLE MATERIALS.
5. HOLE IN THE WALL APPLICATIONS.
INSTALATIONS MUST COMPLY WITH BS;
5871/3 2005. REFER TO 2.10A AND FIG 3.
FOR POSITIONING
6. HEARTH APPLICATIONS. THE FIRE MUST
STAND ON A NON-COMBUSTIBLE HEARTH.
THE HEARTH MATERIAL MUST BE A
MINIMUM OF 12.5mm THICK. ITS TOP
SURFACE SHOULD BE 50mm ABOVE THE
FLOOR LEVEL TO DISCOURAGE THE
PLACING OF RUGS, CARPETS OR OTHER
COMBUSTIBLE MATERIALS OVER IT. THE
FINISHED HEARTH LEVEL MUST EXTEND
300mm BEYOND THE VERTICAL FACE OF
THE FIREPLACE OPENING FOR BOTH THE
16” AND 18” MODELS. THE MINIMUM WIDTH
OF THE HEARTH MUST BE 650mm FOR THE
16” VERSION AND 700mm FOR THE 18"
VERSION.
7. THE FIRE MUST NOT BE FITTED AGAINST A
COMBUSTIBLE WALL.
8. THE MINIMUM HEIGHT ABOVE THE TOP
SURFACE OF THE HEARTH FOR ANY
PROJECTION (e.g. SHELF etc.) 150mm DEEP
MADE FROM WOOD OR ANY OTHER
COMBUSTIBLE MATERIAL IS 766mm. FOR
COMBUSTIBLE PROJECTIONS ABOVE
150mm DEPTH ADD 12.5mm TO THE ABOVE
CLEARANCE FOR EVERY 25mm OF
ADDITIONAL PROJECTION DEPTH.
9. NEVER THROW PAPER OR OTHER
MATERIAL ONTO THE FIRE.
10. IT SHOULD BE APPRECIATED THAT
ALTHOUGH THIS APPLIANCE CONFORMS
TO ALL THE REQUIRED STANDARDS, IT IS
A DECORATIVE FUEL EFFECT HEATING
APPLIANCE WITH AN OPEN FLAME AND
CERTAIN PARTS OF ITS SURFACE WILL
BECOME HOT. A SUITABLE GUARD, WHICH
COMPLIES WITH THE REQUIREMENTS OF
B.S. 8423 IS THERFORE RECOMMENDED
FOR THE PROTECTION OF THE VERY
YOUNG, THE ELDERLY OR THE INFIRM.
SUCH A GUARD IS ALSO RECOMMENDED
FOR THE PROTECTION OF PET ANIMALS.
11. ALWAYS SWITCH THE FIRE OFF AND
ALLOW SUFFICIENT TIME FOR IT TO COOL
DOWN BEFORE HANDLING ANY
COMPONENTS.
12. PLEASE NOTE THAT THIS APPLIANCE
RETAINS HEAT FOR A LONG TIME AFTER IT
HAS BEEN TURNED OFF.
PLEASE NOTE
On first lighting your new fire, a slight odour may
occur due to its new condition. This is quite
normal and will disappear after a few hours use.
After some hours use, the ceramic coal or other
ceramic pieces may change colour. This is quite
normal.
Type. Due to the nature of this kind of burner,
there will be various “popping” and flame noises
not usually associated with ordinary gas fires,
these noises are perfectly normal.
The fire has been designed to give years of
trouble free service. To maintain its optimum
performance, advantage should be taken of the
regular servicing and inspection facilities
available for gas appliances. Annual servicing is
recommended. These instructions are provided
to help you in operating the fire and should be
kept in a safe place.
V-11-07

4
USER’S SECTION
FUEL EFFECT
This fire in certain models is supplied with ceramic
fuel effect pieces to simulate a real fire and a
granular bed to provide flame distribution across
the bed. These items are safe to handle and they
are designed for easy re-fitting after removal.
Gas consumption
Please refer to the general data on page 6 item 1
OPERATING INSTRUCTIONS -
Manual Version
Figure 1
OFF
IGNITION
HIGH
LOW
For your safety, the fire is fitted with a Flame
Supervision Device (FSD), which will shut off the
gas supply if for any reason the pilot is
extinguished. This device incorporates a fixed
probe, which senses heat from the pilot burner
flame. If the probe is cool, the device will prevent
any gas flow unless the control knob is pushed in
at the IGNITION position.
If for any reason the flames go out or if the fire has
been turned off for any reason, always WAIT FOR
3 MINUTES before attempting to relight.
TO LIGHT THE FIRE
1. From the off position, SLOWLY push in
and turn the control knob anti-clockwise to
activate the spark at the IGNITION
position.
2. Keep the control knob pressed in at this
position for approximately 10 – 20
seconds to allow the Flame Supervision
Device to warm.
3. Release the control knob. The pilot should
remain lit independently.
SELECT THE BURNER FLAME LEVEL
NOTE: When first turned on the flames will appear
predominately blue. The ceramic bed will take time
to warm up.
1. After lighting the pilot as described above,
turn the control knob anti-clockwise to the
HIGH position. The fire will now ignite.
2. To decrease the amount of flame push the
control knob in slightly and turn to the
LOW position. The fire can now be used at
any desired setting at any position
between minimum (LOW) and maximum
(HIGH).
TO TURN OFF
1. Push in and turn the control knob
clockwise to the OFF position to
extinguish the flames and the pilot flame.
2. If desired he pilot flame can be left on to
make it quicker and easier to light the fire.
Although the pilot is using gas all the time
it is on, the amount used is minimal. To do
this turn the control knob to the IGNITION
position instead of the OFF position as
described above. If the fire is to be
switched OFF for long periods, it is
recommended that the control knob be
turned to the OFF position.
CLEANING
All cleaning MUST be carried out when the fire is
cold. NOTE: Heat is retained for some time after
the fire is switched OFF. Clean the surround and
fender parts with a slightly damp cloth and then
dry. Abrasive cleaners should NOT be used.
Normally the fire should only need dusting. Light
coatings of soot will usually be burnt off during the
normal operation of the fire. If however, particles of
mortar from the chimney accumulate these should
be removed from the coals and back brick by
dismantling them and cleaning with a soft brush
If soot or other foreign matter has become mixed
with the granular materials and cannot be removed
by hand, remove the contaminated layer and
replace with a clean layer. When levelling ensure
that none of the granules are pushed into the pilot
burner outlet.
If large pieces of debris are found any where in the
fireplace, the chimney and appliance should be
V-11-07

5
inspected and serviced by a competent person
before further use.
OPERATING INSTRUCTIONS -
Remote Control Version
TO LIGHT THE FIRE
(Ensure the battery is connected and batteries are
also in the handset)
To light the fire, point the handset to the sensor on
the front your fire. Push and hold the two buttons
together, on the left hand side of the handset. The
fire will give out a beep sound and you can release
the buttons. After a few seconds you will hear the
clicking spark to the pilot light. Once the pilot is lit
the fire main burner will come on to the high
position (this whole process will take no more than
20 seconds). Fig 2.
TO SELECT THE REQUIRED FLAME
LEVEL
To turn down the fire, point the handset to the
sensor on your fire then push and hold the minus
button (small flame), if you release immediately
the flame will go to low if you hold the flame will
lower slowly and you can release the button to
your desired position.
To turn the fire up, point at the sensor, push the
plus button until the desired flame height is
reached.
The fire may be left in the standby mode (pilot
only) by pressing the small round button on the
handset.
TO TURN OFF
To turn your fire off, point the handset at the
sensor and push the top left button. The fire will go
out.
OXYGEN DEPLETION SYSTEM
If the Oxygen Depletion System (ODS) operates,
i.e. shuts off the gas supply to the fire, WAIT FOR
THREE MINUTES and follow the operating
instructions on pages 4 and 5.
The ODS is designed to shut off the gas supply to
the burner if the oxygen content of the room falls
below a certain level. If it continues to operate then
contact your installer to have the fire and flue
system checked.
SERVICING AND MAINTENANCE
If your fire requires servicing or maintenance,
please contact your supplier quoting the model
name and the serial number. Both of which can be
found on the data badge, which is located next to
the control knob behind the ash pan cover.
BATTERY REPLACEMENT
HAND SET. USE ALKALINE BATTERIES ONLY
(9 Volt PP3)
IN THE HANDSET
BATTERIES IN THE UNIT. THE BATTERY PACK
IS LOCATED BEHIND THE GLASS PANEL ON
THE RIGHT BOTTOM EDGE OF THE FIRE.
PULL THE PACK TO THE SIDE BEING
CAREFULL NOT TO DAMAGE THE CABLE IT IS
ATTACHED TOO. REPLACE ONLY WITH 6 “AA”
ALKALINE BATTERIES
FUEL BED ASSEMBLY
The granular dispersal compound provided in a
plastic bag should be poured into the burner
vessel and gently levelled to the lip of the tray.
Remove any spilt granules from under or around
the burner and particularly from the pilot assembly.
ALWAYS ENSURE THAT THE GRANULAR
MATERIAL LIES LOOSELY AND IS NOT
ALLOWED TO COMPRESS.
Pebbles or ceramic chippings The ceramic
components come in a sealed plastic bag do
not tip onto the burner tray as this will cause
dust which could impair the pilot performance.
Ensure that the pebbles or chippings are placed
evenly in a single layer ensuring there is a gap
directly in front of the pilot to ensure correct
lighting of the burner.
FIG 4.
DETAIL A
SCALE 1 : 1
A
KEEP THIS
AREA
CLEAR
V-11-07