Skinact Palermo User manual

Spa Equipment
&
Toll Free: 1.800.418.0830 www.skinact.com
www.spaandequipment.com International: 818.834.6640
Palermo Spa Facial Treatment Table
User Manual

Toll Free: 1.800.418.0830 www.skinact.com
www.spaandequipment.com International: 818.834.6640
Spa Equipment
&
Copyright © 2021 Spa and Equipment, All Rights Reserved
NOTICE
No part of this document may be photocopied, reproduced, or trans-
lated into any other language without prior written consent of Spa and
Equipment/SkinAct.
e information in this document is subject to change without notice
at any time and should not be construed as a commitment by Spa and
Equipment/SkinAct.
Spa and Equipment/SkinAct assumes no responsibility for any errors
that may be in this document, nor does it make expressed or implied
warranty with regard to this material, including, but not limited to,
the implied warranties of merchantability and tness for a particular
purpose.
Spa and Equipment/SkinAct shall not be liable for incidental or con-
sequential damages arising out of the furnishing, performance, or use
of this document and the program material which it describes.
P. 2

Pinch Points
!
Pinch Points
!
P. 3
Precautions
• Read this manual carefully before installation and operation.
• No one should ever sit on the foot rest or backrest areas.
• is unit should only be operated by trained professionals.
• Keep children from using or playing on the unit.
• Do not stand on any portion of the unit.
• Ensure the unit is kept dry and free of water. Also, make sure any
attachments like remote controls are free of water.
• When operating the unit, ensure that your and your clients’ hands
or other body parts cannot be pinched by the moving parts (see
pinch points below).
• If you have gone through the troubleshooting steps in this manual
and an issue persists, please call Spa and Equipment/SkinAct for
further assistance: 1(800)418-0830
• OPERATE AT YOUR OWN RISK AND USE COMMON SENSE:
OWNER/OPERATOR IS RESPONSIBLE FOR HIS/HER OWN
SAFETY AS WELL AS ANYONE NEAR OR ON THE UNIT.

Cut from
inside
Lay the side
down
Scan to see
video
Cut from inside
the box
P. 4
INSTRUCTIONS
• When you receive the box, carefully cut the tape on the top aps and
open the top (see photo below).
• To see a video about removing your item from the box, visit https://
youtu.be/OGIz0NLdW1I or scan the QR code below.
• en you can cut one short side of the box and lay it down. is
makes it easier to carry the item out of the box.
• Make sure to cut from the inside of the box. is helps to protect
from accidentally cutting your unit.
Removing From The Box

Furniture Dolly
Pallet Jack
P. 5
Removing From The Box
• Please keep all packaging materials. is helps in the event that you
need to return the unit for whatever reason.
• TEAM LIFT: Make sure to have at least two people to li and move
the unit.
• Do not li from the head rest or foot rest areas.
• For this unit, it is best to li with one hand on the metal where the
arm rest connects to the unit (1) and another hand where the hand
remote goes (2). Do not grab the metal hook that the hand remote
hooks onto.
• Li the unit with your partner and walk it out of the box.
• We recommend setting the unit on a furniture dolly or pallet jack
when and where it is practical to use one. Otherwise, you can carry
the unit to your desired location.
One hand here
One hand here
2
1

P. 6
Installation
• Please keep all packaging until you test all the functions.
• Place the unit in the desired location in your space. Attach the arm
rests, head rest, and any other accessories.
• Ensure the ground below the bed is at and not wet or slippery.
• If the bed wobbles on your oor, adjust the leveling feet (photo below)
by spinning them to raise or lower them. e foot that the clears the
oor when you rock the table is the one that will need adjustment.
• Once you have extended one of the feet to x the wobbling, if your
feet have an adjustable nut like in the photo below, you can spin the
nut up until it reaches the metal of the base.
• Ensure the power cable is connected to the unit and plug it into an
appropriate wall outlet.
• Test all of the motor functions on the unit. Ensure the hand remote
works as it should.
Lock foot
with nut
Leveling
feet

P. 7
Reset
Button
Chair Rotation Lock
!
• On the backrest there are controls for the backrest, seat tilt, and table
height.
-Above the controls on the backrest is a reset button (see below).
When the reset button is pressed, the unit automatically returns to
the seated chair position and lowest height. It is recommended the
chair be in this position when a client gets on or o the chair.
-Also, when a client gets on or o, ensure the chair rotation is
locked (see below).
-Another thing to help a client get on or o is to swing one of the
arm rests out of the way for him or her.
• On the seat cushion there are controls for the backrest, seat tilt, leg
rest angle, and table height.
• On the leg cushion there is a button for the leg rest angle.
Motor Controls on the Palermo

P. 8
Not all buttons on the hand remote have a function. Please see below to
see what each button does.
* e motors will be locked and no buttons will work to move the bed.
** Reset button automatically returns the unit to the seated chair position
and lowest height. It is recommended the chair be in this position when a
client gets on or o the chair.
Hand Remote Use
Backrest up & down
Seat tilt back & forward
Chair height up & down
Leg rest up & down
Reset button **
Locks bed*

Adjustable
Height:
25”-37”
74.5” W/ head rest and foot rest on
80.5” W/ head rest and foot rest extended
59” W/O head rest and foot rest on
37.5” 22.5” in Front
27” in Back
P. 9
Measurements

24”
33”
23”
10”
22”
20”
11.5”
6.5”
P.10
Measurements

P.11
'LPHQVLRQV6SHFL¿FDWLRQV
Maintenance
• Length without leg rest or head rest attached: 59”
• Length with leg rest extension and head rest on: 74.5”
• Length with leg rest extension and head rest out: 80.5”
• Width without arm rests: 23”
• Width with arm rests: 33”
• Heights: 25” - 37”
• BASE ONLY Dimensions: 37.5” L x 22.5” W in front: 27” W in back
• Backrest angle: 0° at to 80° inclined
• Footrest angle: 0° at to 85° declined
• Seat tilt angle: 0° to 10°
• Rotation: 150°
• Capacity of 350 lbs
• Colors available: Black or White
* All height measurements are from ground to top of cushion *
** All measurements have a 0.25 to 0.75 inch tolerance **
*** Hand remote control sold separately ***
• When cleaning and sanitizing, do not use bleach, Barbicide, or other
harsh chemicals. Using harsh chemicals can damage the upholstery.
• Simple Green or upholstery cleaners work great for cleaning the up-
holstery. We recommend using Lysol Wipes for sanitizing the uphol-
stery.
• Clean and sanitize the upholstery aer each treatment.
• Every six months, visually inspect the parts of the unit. If there are
any abnormal noises or vibrations during operation, call Spaande-
quipment/SkinAct and describe the situation.

P.12
Troubleshooting
Warranty
Issue Possible Reason Solution
Motorized sections
not moving.
e power cord is not
connected properly.
1) Ensure outlet is work-
ing.
2) Ensure cord is connect-
ed well.
Hand (or foot) remote is
not working.
1) Ensure hand (or foot)
remote is plugged in well.
2) Replace the hand (or
foot) remote.
Control box not working. 1) Contact Spaandequip-
ment/SkinAct Technical
Department: 1(800)418-
0830
Abnormal sounds or vi-
brations.
Parts need lubricating oil. 1) Add lubricating oil.
Motor quality issues. 1) Contact Spaandequip-
ment/SkinAct Technical
Department: 1(800)418-
0830
• is item has a 1-year limited warranty for malfunctions and manu-
facture defects only (parts, labor, and shipping not included). THIS
WARRANTY IS VOID IN THE EVENT EQUIPMENT IS DAM-
AGED BY IMPROPER USE.
• To read the full Warranty Policy, please visit https://www.spaande-
quipment.com/Return-Warranty-Repair-Policy.html or scan the QR
code below.
Scan for
warranty