2
3
4
5
6
1
ALL-IN-ONE
SWING TRAINER
USAGE GUIDE
PARTS & INITIAL SETUP
Thank you for choosing a SKLZ All-In-One Swing Trainer. We are dedicated to
providing you with the best tools and instruction possible to help you unleash your
athletic potential. If there is anything else we can do to help you optimize your
call (1-877-225-7275). Visit www.SKLZ.com for product videos, drills, and additional
products for use with All in One Swing Trainer
BEFORE YOU BEGIN:
» Read all setup and usage instructions carefully.
» This product is not suitable for children under 3 years of age.
» Always check equipment for wear or damage before use. If any is found,
do not use product. If any components are missing, please contact SKLZ
toll free at 1-877-225-7275 x128.
CAUTION:
» When in use, make sure your All-In-One Swing Trainer is set up in a clear area to
avoid damage to property.
» When using your All-In-One Swing Trainer, please have others stay clear of the
hitting area to reduce the risk of injury.
» Do not store in extremely high or low temperatures to avoid damaging or reducing
the life of your All-In-One Swing Trainer.
» Do not leave your All-In-One Swing Trainer outdoors for extended periods of time.
» All-In-One Swing Trainer can be used by right and left handed golfers.
» All-In-One Swing Trainer can be adjusted in more ways than suggested here
in the instructions.
IMPORTANT:
SAVE THIS INFORMATION IN THE EVENT THAT THE
MANUFACTURER NEEDS TO BE CONTACTED FOR
REPLACEMENT PARTS.
ISAFETY INSTRUCTIONS:
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR
PROPERTY DAMAGE AND WILL VOID YOUR WARRANTY.
Most injuries are caused by misuse and/or not following instructions. Use caution when using
this product.
INSTRUCTION MANUAL INCLUDES:
» All-In-One Swing Trainer
» Usage guide
ASSEMBLY
BASE
BASE POLE
FILL CAP
T-CONNECTOR
MOUNT
T-CONNECTOR
SECONDARY
POLE
ROUND END
FOAM PADS
FOAM PADS (2)
Your All-In-One Swing Trainer is designed
to provide the largest possible number of
configurations to use as an aide to better swing
and stance habits. Both the lower Base Pole and
the attached Secondary Pole can be extended
or retracted, raised or lowered, and rotated
to horizontal. The included foam pads may be
added or removed to provide a comfortable
contact point for some setups. Familiarize
yourself with the included components before
beginning assembly.
1 - Remove the Fill Cap (A) and fill the Base (B)
with water or sand to make the Base rest
solidly on the ground. When base is full,
make sure to move base around to evenly
distribute water or sand throughout the
entire base unit. If this is not done the base
will be uneven and will result in tipping over.
2 - Holding the Base steady, raise the Base
Pole (C) upright. The silver Release Buttons
will snap into the first of four holes, in the
vertical position.
3 - Slide the T-Connector Mount (D) a few inches
on to the Base Pole and snap the clamp shut.
Exact placement is not important; it can be
repositioned at any time.
4 - Slide the T-Connector (E) on to the
Secondary Pole (F) and clamp in place near
the center.
5 - Slide the two round-end Foam Pads (G) and
(H) onto each end of the Secondary Pole.
NOTE: the two Pads have different diameter
openings to match the opposite ends of the
pole. Match the diameters so both pads fit.
6 - If desired, install the two additional pads (I)
onto the length of the Secondary Pole as
needed. These can be simply slipped over
the Secondary Pole using the long cut down
the length of the pad.
7 - Attach the Secondary Pole to the Base
Pole by pressing together the two parts of
the T-Connector.
The Secondary Pole can be rotated any time
at the T-Connector; press it firmly into place to
hold a position. Both Poles can be extended by
pressing the silver Release Button near one end
and pulling out the extension.
PUSH BUTTON TO
RELEASE POLE
FILL CAP
7
B
G H
D
E
F
A
C
I
