SKYDANCE LP-150M-12 User manual

User Manual Ver 1.0.2
Model No.: LP-150M-12, LP-150M-24
Features
Page 1
0/1-10V Constant Voltage LED Driver
● Dimming interface: 0-10V, 1-10V, 10V PWM, Resistor, AC Push-Dim
● Universal AC input / 100-277VAC
● 1 channel constant voltage output, Max. total output power 150W
● Built-in active PFC function: 0.98 Typ
● Synchronize on multiple number of LED drivers
● Over-heat / Over-voltage /Over-load / Short circuit protection
● Suitable for indoor LED lighting application
● 5 Year, 50,000hr warranty
Technical Parameters
LP-150M-12, LP-150M-24 0/1-10V Constant Voltage LED Driver
Applications
● Suitable for LED related xture or appliance which use LED light bar and LED tape (like LED Decoration or Advertisement devices).
● Ofce / Commercial / Domestic Lighting, Hotels, Retail and Display.
● Use for retrot upgrades & new luminaire designs.
Warranty
5 years
Short Circuit
Protection
Over Load
Protection
Over-heat
Protection
Synchronization
Digital
Dimming
Push-Dim
0/1-10V
Dimming
Output Voltage 12VDC
Output Current Max. 12.5A
Output Power
Dimming Range
PWM Frequency
Input Voltage Range
Frequency Range
Efficiency 92％/230VAC
Alternating Current 2A/100VAC, 0.75A/230VAC, 0.7A/277VAC
Inrush Current
Leakage Current
No Load Power 2W/100VAC, 2W/230VAC, 2.5W/277VAC
Over Load
Over Temperature
Woking Temperature
T-case Max
Working Humidity
Storage Temperature/Humidity
Temperature Coefficient
Vibration Resistance
Security Specifications
Withstand Voltage
Insulation Resistance
EMC Emission
EMC Immunity
Shut down the output Voltage, when the load>=110％～140％, auto recovers.,
Short Circuit
Protection
Environment
Safety&EMC
-20℃～50℃
90℃
0～100％
2000Hz
100～277VAC
50/60Hz
Output
Model
Input
＜5mA
Max. 150W
Cold start 71A at 230VAC
20％～90％RH, non-condensing
-40℃～80℃10％～95％RH,
±0.03％/℃ (0-50％)
10-500Hz, 2G, 6min/cycle X,Y,Z axes/2min,
IEC/EN61347-1, IEC/EN61347-2-13, GB19510.14
I/P-O/P: 3750VAC
I/P-O/P: 100MΩ/500VDC/25℃/70％RH
EN61000-4-2.3.4.5.6.8.11, EN61547
EN55015, EN61000-3-2 Class C, IEC61000-3-3
Ripple & Noise <=150mV 230/ VAC
IP Rating
Certications
IP20
CE
24VDC
Max. 6.25A
LP-150M-12
Power Factor >0.98/230VAC
L-N:1KV
Anti Surge
THD ＜5％/100VAC, ＜10％/230VAC@ half lood/277VAC@75%load
Startup time 2S/100VAC, 1S/230VAC
LP-150M-24
Over Voltage Shut down the output Voltage, when the Voltage>=110％～140％, re-powerontorecover
Shut down the output Voltage, re-powerontorecover
Shut down the output Voltage, re-powerontorecover
Mechanical Structures and Installations
310.00 mm
45.00 mm
30.00 mm
L
N
L1
Push DIM
LL1
Vo+
Vo
AC N input
AC L input
AC Push input
LED output -
LED output +
DIM
DIM +
0/1-10V input -
0/1-10V input +
Gross weight
Net weight
Dimming Curve
100
90
80
70
60
50
40
30
20
10
PWM duty(%)
50 60 70 80 90 100
Brightness(%)
10 20 30 40
Gamma=1.6
AC Push dimming 0/1-10V dimming
100
90
80
70
60
50
40
30
20
10
5.0 6.0. 7.0 8.0 9.0 10.0
0/1-10V(V)
1.0 2.0 3.0 4.0
Gamma=1.6
PWM duty(%)
Installation precautions
Please do not stack the products.
The distance between two products should be ≥1m
so as not to affect heat dissipation and lifespan of the products.
≥1m
≥1m ≥1m
420g
450g

User Manual Ver 1.0.2 Page 2
LP-150M-12, LP-150M-24 0/1-10V Constant Voltage LED Driver
100120140160180
20
40
60
80
100
AmbienTemperature,Ta(℃)
Load(%)
Static characteristic
Input voltage(VAC) 50/60Hz
-10 100 20 30 40 50 60 70
20
40
60
80
100
Load(%)
-20
Output Load VS Temperature
200 220 240 260 280
200 3040608010090
20
40
60
80
100
Load(%)
-20
L
N
L1
Push DIM
LL1
Vo+
Vo
DIM
DIM +
● Short press:
Turn on or off light.
● Long press (1-6s):
Press and hold to step-less dimming,
With every other long press, the light level goes to the opposite direction.
● Dimming memory:
Light returns to the previous dimming level when switched off and on again, even at power failure.
● Synchronization:
If more than one LED driver are connected to the same push switch, do a long press for more than 10s,
then the system is synchronized and all lights in the group dim up to 100%.
This means there is no need for any additional synchrony wire in larger installations.
We recommend the number of LED drivers connected to a push switch does not exceed 25 pieces,
The maximum length of the wires from push to LED driver should be no more than 20 meters.
Wiring Diagram
1. 0/1-10V Connection
● The 0/1-10V input is operable via commercially available simple rotary wall switchs designed for 0/1-10V
dimming equipment or from decicated system central dimming controllers.
● Compliant with 0-10V, 1-10V, 10V PWM, RX(4 in 1).
● We recommend the number of LED drivers connected to 0/1-10V dimmer does not exceed 50 pieces,
The maximum length of the wires from dimmer to LED driver should be no more than 50 meters.
● If the LED driver be used with the RF remote or Push-Dim interface prior to using the 0/1-10V interface,
the 0/1-10 V signal should change over 10% to return 0/1-10 V control.
2. AC Push-Dim connection
The provided AC Push-Dim interface allows for a simple dimming method using commercially available non-latching
(momentary) wall switchs.
0-10V
1-10V
PWM(500Hz-3KHz,10V)
RX(200K-500K)
Single color LED strip
AC Power
50/60Hz
PushSwitch
L
N
Single color LED strip
Single color LED strip
L
N
L1
Push DIM
LL1
Vo+
Vo
DIM
DIM +
L
N
L1
Push DIM
LL1
Vo+
Vo
DIM
DIM +
Failure analysis and troubleshooting
CaseTemperature,TC(℃)
fault cause solution
The light can not be turned on 1. no power
2. Wrong wiring 1. Check the power supply
2. Connection test
brightness of the light is
inconsistent 1. Output cable is too long
2. Wire diameter is too small
1. Reduce wire length or loop power
supply
2. Replace Replace to thicker wires
Hiccup ashing light Overload Check the power of the light
Multiple LED drivers are
out of sync Inconsistent switch gradients All initialization, unied setting,
switch gradient