skyvoe NXG-65 User manual

Ceiling Tilt Mount
Installation Manual
NXG-65 / NXG-70 / NXG-80
Adjustable Fixed
Adjustable or Fixed Ceiling Mount Columns should be fully assembled and
secured to the ceiling prior to the following the instructions in this manual.

1
InstallatIon ManualnXG 6550 / 7070 / 8070 |
Included in the tilt mount kit:
Tools Required for Installation:
Additional Parts Needed:
2- Mounting Arms
1- Mounting Plate
2- Locking Bars
Ratchet with 1/2” Socket 1/2” Wrench
1/2”
1/2”
These parts are found in the supplied Ceiling Mount Parts (CMP-1) box.
4 qty.
5/16” Hex Head Bolts
8 qty.
SS Flat Washers
4 qty.
5/16” NyLock Nuts

2All Rights Reserved. 2017 SkyVue®
Installation Manual - Tilt Mounts
Lay television down, viewing side down on blanket.
Lay blanket down on at
sturdy surface. Run hand
over surface to make sure
there are no sharp object
or protrusions, when the
television is laying down.
Gather the 4clamping nuts with springs. These will be in a separate
bag shipped with the User Manual Packet.

3
InstallatIon ManualnXG 6550 / 7070 / 8070 |
Align Holes Secure Screws
1: Remove the hex head screws and
washers. Set the screws and washers in a
secure location.
2: Insert spring nuts as shown in
picture (2 per power strut). Spring should
be touching both sides of the power strut
as shown.
3: Align holes of the mounting arms
with the holes of the clamp nut springs.
The arms should be level with each
other. Insert the hex head screws and
washers from the rst step and secure
tightly as shown in the example to the
right and below.

4All Rights Reserved. 2017 SkyVue®
Installation Manual - Tilt Mounts
Adjustable or Fixed Ceiling Mount Columns should be fully assembled and
secured to ceiling prior to the following steps.
Locate lower mounting plate.
Align holes from Tilt Mount Plate
to Column Mounting Plate.
Place the 4 provided 5/16” hex
head bolts with at washers
through the aliened plate holes.
X 4
X 4
Listed parts are found in the supplied
Ceiling Mount Parts (CMP-1) box.
• 4 - 5/16” Hex Head Bolts
• 4 - SS Flat Washers

5
InstallatIon ManualnXG 6550 / 7070 / 8070 |
With a 1/2” wrench on the
bolt head and a ratchet with
1/2” socket on the NyLock
nut - tighten and secure plates
together.
On the back of the mount, place
the 4 provided at washers
and 4 provided NyLock nuts on
exposed bolt threads.
Listed parts are found in the supplied
Ceiling Mount Parts (CMP-1) box.
• 4 - SS Flat Washers
• 4 - 5/16” NyLock Nuts
X 4
X 4

6All Rights Reserved. 2017 SkyVue®
Installation Manual - Tilt Mounts
With the help from a friend, lift the television and attach the hooks on the
mounting arms to the plate on the tilt mount. Tighten knobs on arms once
the tilt is set correctly for the television.
Once the television is hung on the plate. Be sure to tighten the position set
screw on the bottom of the mounting arm to secure the television in place.
HOOK
Connected
to
Ceiling
SECURE BY INSERTING LOCK BAR AND
FASTENING PAD LOCK
SET & TIGHTEN
KNOBS
Congratulations you have successfully installed your tilt mount. If you have
any questions feel free to contact our technical support team
[phone] option 2
Mounting Arm
Mount Plate
Locking Bar

7
InstallatIon ManualnXG 6550 / 7070 / 8070 |
Notes: