skyvoe NXG-32 User manual

Tilt Mount Installation
Manual
NXG-32

2
InstallatIon ManualnXG 32 |
Included in the tilt mount kit:
Tools Required for Installation:
2- Mounting Arms
1- Mounting Plate
2- Tilt Control Knobs
2- M6 Carriage Bolts
2- Flat Washers
2- Star Washers
4- 5/16”x 2 ½” Lag Screws
4- 5/16” Lag Shields
4- 5/16” Flat Washers
Ratchet with 1/2” Socket Drill with 1/2” Masonry Bit or
3/16” Wood Bit
1/2”
Masonry Wood
1/2”
3/16”

3All Rights Reserved. 2017 SkyVue®
Installation Manual - Wall Tilt Mount
Gather the following:
1. Slide the M6 bolt through the hole on the Control Arm
2. Place the ABS washer on the thread side of the bolt.
3. Place the lock washer on the thread side of the bolt.
4. Place then twist the knob on to the bolt.
Do not tighten all the way this will control the amount of tilt the television
has once it is put on the wall bracket.
Tilt Control Knob
x 2 x 2 x 2 x 2
M6 Bolts Lock Washer ABS Washer

4
InstallatIon ManualnXG 32 |
Warning: Do not plug speaker bar into A/C outlet until connections to the tele-
vision have been plugged in. This will severely damage the speaker bar if not
followed completely.
Lay television down, viewing side down on blanket.
Lay blanket down on at sturdy
surface. Run hand over sur-
face to make sure there are no
sharp object or protrusions,
when the television is laying
down.

5All Rights Reserved. 2017 SkyVue®
Installation Manual - Wall Tilt Mount
Remove and set aside the 4 screws and washers as indicated with
the red circles.
Align holes of the mounting arms with the holes on the back of the
television. Reinsert the screws and washers from previous step and
tighten securely.
Align Holes Secure Screws
Note:
Both kNoBs Need
to face the sides of
the televisioN

6
InstallatIon ManualnXG 32 |
For Masonry:
Set height, level, and mark drill locations on wall. With masonry bit, drill
1/2” pilot holes and hammer in lag bolt shields. Hold the plate to the wall.
Make sure the plate is level. Using the 4 supplied lag bolts and washers
secure plate to the wall.
For Wood:
Set height, level, and mark drill locations on wall.
IMPORTANT: Make sure that drill marks are located where bolts will get secured
in a stud or a substantial wood structure.
With wood bit, drill 3/16” pilot hole. Hold the plate to the wall. Make sure
the plate is level. Using the 4 supplied lag bolts and washers secure plate
to the wall.
For Anchoring Into
Masonry Wood

7All Rights Reserved. 2017 SkyVue®
Installation Manual - Wall Tilt Mount
With the help of a friend lift the television and attach the hooks on the
mounting arms to the plate on the tilt mount. Tighten knobs on arms once
the tilt is set correctly for the television.
Once the television is hung on the plate. Be sure to tighten the position set
screw on the bottom of the mounting arm to secure the television in place.
HOOK
SECURE BY
TIGHTENING
SET SCREW
SET & TIGHTEN
KNOBS

8
InstallatIon ManualnXG 32 |
Congratulations you have successfully installed your tilt mount. If you have
any questions feel free to contact our technical support team
[phone] option 2.

9All Rights Reserved. 2017 SkyVue®
Notes: