Skyworks Si4731-DEMO User manual

Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [e-mail] • www.skyworksinc.com
Rev. 0.1 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 4, 2021
Si4731-DEMO
Si4731 DEMO BOARD USER’SGUIDE
1. Features
Worldwide FM band support, 76–108 MHz
Worldwide AM band support, 520–1710 kHz
Auto seek/auto scan
48 FM and 48 AM station presets
FM Radio Data Services (RDS) decoding (Pi Pty Ps RT CT AF displays)
Automatic set time/date function via RDS
Automatic Alternative Frequency (AF) switching
Automatic AM channel spacing detection
Single battery operation down to 0.9 V or three battery operation
Adjustable parameters include
Tuning spacing
Seek SNR/RSSI thresholds
Soft mute SNR/RSSI thresholds
Channel filters
Stereo and mono blend thresholds
Band limits
De-emphasis (50 or 75 µs)
AM channel spacing detection threshold
Stereo/mono indicator
Volume control with mute function
AM/FM band and signal quality indicator display
Battery voltage indicator
Calendar display
3x4 matrix keypad interface
Direct input of station frequencies
2. Overview
The Skyworks Solutions Si4731-DEMO board provides a complete portable AM/FM radio design with numerous
enhanced features that demonstrate the capabilities of the Skyworks Solutions AM/FM and MCU product families.
The Si4731-DEMO comes in a 3x3 mm 20-pin QFN package and is layout compatible with the entire Skyworks
Solutions Si47xx radio family of FM receivers, transmitters, and transceivers. The host MCU is a Skyworks
Solutions C8051F930 with internal oscillator and built-in DC-DC converter. A 79 x 101 dot matrix LCD provides the
flexibility to display a variety of system information including RDS. The demo board can work with either one AA
battery using the dc-dc converter of the C8051F930 MCU or three AAA batteries.

Si4731-DEMO
2 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [e-mail] • www.skyworksinc.com
Rev. 0.1 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 4, 2021
3. Description
Figure 1 and Figure 2 shows the physical layout of the board with key components indicated.
Figure 1. Si4731-DEMO Board Top Side in Calendar Mode
Figure 2. Si4731-DEMO Board Bottom Side
U3
J5

Si4731-DEMO
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [e-mail] • www.skyworksinc.com 3
Rev. 0.1 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 4, 2021
Power:
S14: 3 cell / 1 cell selection
S15: Power on / off
Audio connectors:
J14: Audio input (unused)
J15: Audio headphone output
Antenna selections:
J1: FM whip antenna connector
J2: FM SMA connector for FM conductive testing
J3: AM SMA connector for AM conductive testing
J4: AM air loop antenna wire connector
J5: JTAG connector
T1: Transformer for AM air loop operation (not shown)
JP1: FM antenna input selection
JP2: AM signal input selection
JP3: AM antenna type selection
Open: AM ferrite loop stick antenna
Short: AM air loop antenna
JP4: FM PCB antenna selection
Short: Embedded PCB trace as FM short antenna for Si4704/05/1x/2x
Open: No PCB short antenna
Main components:
LCD: 79x101 dot matrix LCD
U1: Skyworks Solutions Si4731 AM/FM/RDS tuner
U2: Audio amplifier
U3: Skyworks Solutions C8051F930 MCU
U4: LDO
Control interface:
Reset Key: Reset button
KeyPad: 3x4 matrix buttons for human interface
1-2: FM SMA (J2)
1-3: FM whip antenna (J1)
1-4: FM headphone (J15)
3
42
1
1-2: AM ferrite loop stick
1-3: AM air loop (J4)
1-4: AM SMA (J3)
3
4
2
1

Si4731-DEMO
4 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [e-mail] • www.skyworksinc.com
Rev. 0.1 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 4, 2021
4. Operation
This section describes the operating modes of the Si4731-DEMO board. The board provides two major modes of
operation: Calendar and AM/FM radio.
4.1. Calendar Mode
Upon power on, the board automatically enters the Calendar Mode and displays the following information:
Year-month-day
Hour-minute
Day of the week
Battery voltage
The demo board display in Calendar Mode is illustrated in Figure 1.
In Calendar Mode, the SET/9 key is used to enter the setup menu. The M+/3 and M-/7 keys are used to select
different adjustable items (hour, minutes, year, day, month). The UP/4 and DOWN/8 keys are used to set the value
for each selected item.
The Calendar Mode date and time can also be set automatically with RDS Current Time (CT) information from a
broadcast radio station as described in the following section.
4.2. AM/FM Radio Mode
From Calendar Mode, the POWER button is used to enter AM/FM Radio Mode which displays the following
information:
1. Signal SNR indicator
2. Signal RSSI indicator
3. Band frequency indicator
4. Battery voltage indicator
5. Band frequency unit indicator
6. Stereo/mono indicator
7. Volume indicator
8. Band indicator
9. RDS information
The demo board display in AM/FM Radio Mode is illustrated in Figure 3 and Figure 4:
Figure 3. LCD Display in FM Radio Mode
7
1 23
4
5
6
8
9

Si4731-DEMO
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [e-mail] • www.skyworksinc.com 5
Rev. 0.1 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 4, 2021
Figure 4. LCD Display in AM Radio Mode
4.2.1. Band Selection
In Radio Mode, the BANDS/0 key is used to switch between the AM and FM bands.
4.2.2. Time/Date Auto Set
Many radio stations broadcast RDS data including clock/time CT information. The AM/FM demo board can capture
this information to automatically set the time and date. In FM Mode, when RDS CT information is received, the CT
indicator will be displayed. The MEM/AL/1 button can be used to update the calendar date and time with the CT
information. CT information is not available on all radio stations and is normally sent only once per minute.
4.2.3. Alternative Frequency (AF) Switching
The AM/FM demo board monitors RDS for alternate frequency (AF) information. When RDS alternative frequency
information is received, the AF indicator will be displayed. If the signal quality of the currently tuned station
degrades, the radio will automatically change to one of the alternative frequency stations.
4.2.4. Tune/Seek
In Radio Mode, pressing the UP/4 or DOWN/8 button for less than 0.5 s will tune the frequency by the preset step
size. Holding the button for longer than 0.5 s but less than 3 s will perform a station seek.
4.2.5. Scan
In Radio Mode, the MSCAN/5 button is used to scan for all valid stations in the selected band and will automatically
save them into preset selections. After a scan operation, the M+/3 and M-/7 keys will cycle through the preset
station list. Scan operation can be aborted by pressing MSCAN/5 again, or by pressing the UP/4 or DOWN/8 key.
4.2.6. Parameter Settings
In Radio Mode, the SET/9 key is used to select the parameter setup menu as illustrated in Figure 5 and Figure 6.
The M+/3 or M-/7 keys will cycle through the available items in the menu. The UP/4 or DOWN/8 keys are used to
set the desired value for each item. Select “Yes” under “Factory Def” to go back to the factory default settings for all
items.
1 3 2
4
7
5
8

Si4731-DEMO
6 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [e-mail] • www.skyworksinc.com
Rev. 0.1 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 4, 2021
Figure 5. LCD Display in FM Setup Menu
Figure 6. LCD Display in AM Setup Menu
4.2.7. Digit Keys
In Radio Mode, the FUNC/DIGIT key is used to switch the keypad to digital input mode. A “Dig” indicator is
displayed in this mode and all keys marked with a digit are used to input a channel frequency. A frequency is
considered valid if it lies within the band limits. If a non-valid frequency is entered, the closest band limit will be
entered and displayed.
4.2.8. Volume
The VOL+/2 or VOL–/6 keys are used to adjust the volume up or down. The board audio output will be muted when
volume is at the lowest setting.
4.2.9. AM Channel Spacing Auto Set
In AM Mode, the MEM/AL/1 key will automatically detect and set the channel spacing to either 9 or 10 kHz. The
detection criterion determines which channel spacing results in more valid stations during a band scan. The
number for the detection threshold is adjustable as described in Table 2. This operation can be aborted by pressing
the MEM/AL/1 key again.

Si4731-DEMO
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [e-mail] • www.skyworksinc.com 7
Rev. 0.1 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 4, 2021
5. Human interface
There are 12 keys for controlling the demo board as shown in Figure 7:
Figure 7. Human Interface Keys
Each key can have a different function under each operating condition:
Calendar/Powerdown Mode: Radio function is disabled. LCD displays Calendar. Buttons can be used to set
time, etc.
Radio AM/FM Mode: Tuner IC works in powerup mode (FM or AM). Radio function is enabled. LCD displays
the radio station parameters. Buttons are used to adjust radio settings.
Digital Input Mode: Tuner IC works in powerup mode (FM or AM). Radio function is enabled. LCD displays
the radio station parameters. The buttons are used for direct digit input of station frequencies.
The functions of the buttons are summarized in Table 1:
Table 1. Key Function Description
Button/Mode Calendar Mode
Tuner Off
Radio AM/FM Mode
Tuner On
MEM/AL/1 None FM Mode: Used to adjust calendar using received RDS CT.
AM Mode: Used to automatically detect and set the channel spacing.
POWER Enable radio Disable radio function and enter calendar mode.
(Radio parameters will be saved to Flash).
SET Enter calendar setup
menu
Enter radio setup menu.
(Parameter list in Table 2)
BANDS None Change between FM and AM band.
Note: Combination keying is entered and exited from Radio Mode by pressing and holding the SET key then pressing the
BANDS key. A combination of the SET and the MSCAN keys will cycle through the available display items.
MEM/AL/1
MSCAN/5
SET/9
VOL+/2
VOL-/6
M+/3 UP/4
M-/7 DOWN/8
BANDS/0 FUNC/DIGIT POWER

Si4731-DEMO
8 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [e-mail] • www.skyworksinc.com
Rev. 0.1 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 4, 2021
The FM and AM radio parameters which can be configured from setup menu are listed below in Table 2.
UP/
DOWN
Hold
Time <
0.5 s
In setup menu,
change the current
calendar item by one
step.
In setup menu, change the current parameter by one step.
In radio mode, tune up or down by one step.
0.5 s <
Hold
Time
< 3 s
Perform a station seek.
Hold
Time
> 3 s
Fast parameter setting Fast parameter setting.
MSCAN None Scan for all valid stations and save them to presets.
M+/ M– In setup menu, select
next calendar item.
In setup menu, select next adjustable item.
In radio mode, tune to the next preset station.
Vol+ /
Vol–
< 3 s None Increase or decrease volume 1 step.
> 3 s Quickly increase or decrease volume.
FUNC/DIGIT None Shift the keyboard between normal function and digital input mode.
Combination
keying
None A: Radio IC version
B: Firmware version
C: Varactor reading
D: AGC status
Table 2. Radio Configuration Parameters
FM Parameter AM Parameter
Spacing: 50/100/200 kHz
Default: 100 kHz
Spacing: 1/9/10 kHz
Default: 9 kHz
RSSI Seek: 0–127 dBµV
Default: 20 dBµV
RSSI Seek: (0–63 dBµV
Default: 25 dBµV
SNR Seek: 0–127 dB
Default: 03 dB
SNR Seek: 0–63 dB
Default: 05 dB
Pre-emphasis: 50 or 75 µs
Default: 75 µs
Pre-emphasis: 00 disable, 50 µs
Default: 00
Band High Threshold: Max 108 MHz
Default:107.90 MHz
Band High Threshold: Max 1710 kHz
Default:1710 kHz
Table 1. Key Function Description (Continued)
Button/Mode Calendar Mode
Tuner Off
Radio AM/FM Mode
Tuner On
Note: Combination keying is entered and exited from Radio Mode by pressing and holding the SET key then pressing the
BANDS key. A combination of the SET and the MSCAN keys will cycle through the available display items.

Si4731-DEMO
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [e-mail] • www.skyworksinc.com 9
Rev. 0.1 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 4, 2021
Band Low Threshold: min 76 MHz
Default: 87.50 MHz
Band Low Threshold: min 520 kHz
Default: 522 kHz
Channel Filter: 00/40/60/80/100 kHz
Default: 00 (Auto)
Channel Filter: 1/2/3/4/6 kHz
Default: 2 kHz
RClock: 0: AFC disable
32763~32773
Default: 32768
RClock: 0 AFC disable
32763~32773
Default: 32768
Smute Rate: 0–255
Default: 64
Smute Rate: 0–255
Default: 64
Smute SNR: 0–15 dB
Default: 4 dB
Smute SNR: 0–63 dB
Default: 10 dB
Smute Attenuation: (0–31 dB)
Default: 16 dB
Smute Attenuation: 0–63 dB
Default: 16 dB
Blend Mono: 0–127 dBµV
Default: 30 dBµV
Smute Slop: 1–5
Default: 2
Blend Stereo: 0–127 dBuV
Default: 49dBuV
Set Factory Default: on/off
Default:off
AGC Override: on/off
Default: off
AM Channel Spacing Detection
Threshold: 1,2,3,4,5,6
Default = 2
AGC Index: 0–26
Default : 0
Set Factory Default: on/off
Default:off
RDS/RBDS
Default: RBDS
Table 2. Radio Configuration Parameters (Continued)

Si4731-DEMO
10 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [e-mail] • www.skyworksinc.com
Rev. 0.1 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 4, 2021
6. Bill of Materials
C8051F930 MCU with 64 kB Flash program memory, 4 kB RAM, and built-in dc-dc converter
AM/FM receiver IC Si4731 with external 32768 Hz crystal oscillator support
ST7588T LCD driver IC
LM4910 Audio amplifier IC
See Table 3 for details.
Table 3. Si4731 Demo Board Bill of Materials
Item Qty Reference Description Value
1 3 C 1 , C 1 6 , C 2 9 C A P, S M , 0 6 0 3 ,X 7 R 0 . 4 7 µ F
2 2 C4, C13 CAP,SM,0603,X7R 4.7 µF
3 8 C 1 5 , C 2 3 - 2 8 , C 4 1 C A P, S M , 0 6 0 3 , X 7 R 1 µ F
4 6 C 1 0 , C 1 4 , C 1 9 , C 3 7 , C 3 9 – 4 0 C A P, S M , 0 6 0 3 , X 7 R 0 . 1 µ F
5 4 C 2 , C 3 , C 2 1 – 2 2 C A P, S M , 0 6 0 3 , X 7 R 2 2 p F
6 2 C 8 , C 1 2 C A P, S M ,0 6 0 3 , X 7 R 2 2 0 p F
7 2 C 11 , C 1 8 C A P, S M , 0 6 0 3 ,X 7 R 8 2 0 p F
8 3 C5–7 CAP,SM,0603,X7R 100 pF
9 4 C 1 7 , C 3 8 , C 4 4 , C 4 6 C A P, S M , 0 6 0 3 , X 7 R 1 n F
1 0 8 C 3 2 – 3 6 , C 5 4 – C 5 5 , C 4 3 C A P, S M , 0 6 0 3 , X 7 R N P
11 3 C 3 0 , C 4 5 , C 5 3 R E S , S M , 0 6 0 3 0 R
12 1 C9 CAP,SM,1210,tantalum 100 µF/6.3 V
13 1 C31 CAP,SM,1210,tantalum 220 µF/4 V
1 4 4 R 1 – 2 , R 3 , R 2 5 R E S , S M , 0 6 0 3 0 R
1 5 1 1 R 7 , R 2 7 , R 2 9 – 3 2 , R 3 4 , R 3 6 – 3 9 R E S , S M , 0 6 0 3 1 0 k W
16 2 R5, R11 RES,SM,0603 12 kW
1 7 4 R 2 0 , R 2 2 – 2 3 , R 2 8 R E S , S M , 0 6 0 3 1 k W
18 2 R4,R6 RES,SM,0603 5k6
19 2 R8, R10 RES,SM,0603 6k8
20 3 R9, R16–17 RES,SM,0603 2 kW
21 2 R18–19 RES,SM,0603 100R
2 2 5 R 1 5 , R 2 1 , R 2 4 , R 2 6 , R 3 5 RES,SM,0603 NP
23 1 R12 RES,SM , 0 6 0 3 4 k7
2 4 3 R 1 3 – 1 4 , R 3 3 R E S , S M , 0 6 0 3 1 0 0 k
25 4 B1–4 FERRITE BEAD,SM,0805 2k5/100M
26 1 L1 IND,S M ,0603 120 nH

Si4731-DEMO
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [e-mail] • www.skyworksinc.com 11
Rev. 0.1 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 4, 2021
27 1 L2 IND,S M ,0603 270 nH
28 2 L3–4 RES,SM , 0 6 0 3 0 R
29 1 U1 S i 4 7xx, MLP2 0 - 3 M M Si47xx
30 1 U2 LM4910,SOP8 LM4910MA
31 1 U4 REGLATOR,SOT23 XC62FP3002MR
32 1 U3 C8051F920/30-GQ,LQFP32 C8051F920/30-GQ
33 1 D1 DIODE,SM,ESD,SOT23 BAV99
34 2 D2–4 DIODE,SM,ESD,SOT23 CM1214-01ST/SO
35 1 Q1 TRANSISTOR NPN SOT23 2N3904
36 1 T1 MW AIR LOOP ANTE N N A TRANS-
FORMER
SLMWTF01
37 1 J5 CONN,T H,2X10,HD R
38 1 J4 Wire ho lder
39 2 Y1 – 2 Cr y s ta l 32.7 6 8 k H z
40 2 J14– 1 5 Ster e o ea rph o ne j a ck 3. 5 m m
41 2 JP 3 –4 C ON N ,T H , 1X 2 ,H D R CO N N, T H, 1 X 2, H DR
42 2 JP 1 –2 C ON N ,T H , 1X 4 ,H D R CO N N, T H, 1 X 4, H DR
43 4 J1 0 –13 C O NN, T H, 1 X5 , H DR C ON N ,TH , 1X 5 ,HD R
44 1 J1 BNC_VERTICAL BNC for whip
45 2 J2-3 SMA_V E RTICAL S M A f o r FM/AM
46 1 S14 SLIDE SWITCH With 3 Double Pole
Double Throw Switches inside
47 1 S15 Single Pole Double Throw Switch
48 13 S1–13 Button Swi tc h
49 1 L C D1 LC D 10 1* 7 9 d o t s
50 1 A N T2 MW f e rri t e an t en n a 22 0 µ H
51 1 A N T3 MW l o o p an t en n a 1 0– 2 0 µ H
52 1 BAT2 Battery BOX ,AAA*3 SIZE
53 1 BAT1 Battery BOX ,AA SIZE
DC–DC Power Block Circuit Part List
54 1 L5 IND,SM,1008 0.68 µH
55 1 C42 CAP,SM,0603,X7R 4.7 µF
Table 3. Si4731 Demo Board Bill of Materials (Continued)

Si4731-DEMO
12 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [e-mail] • www.skyworksinc.com
Rev. 0.1 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 4, 2021
7. Schematics
Figure 8. Si4731-DEMO Board Schematic—Radio and Audio Portions

Si4731-DEMO
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [e-mail] • www.skyworksinc.com 13
Rev. 0.1 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 4, 2021
Figure 9. Si4731-DEMO Board Schematic—MCU Portion

Copyright © 2021 Skyworks Solutions, Inc. All Rights Reserved.
Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the
information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer.
Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation,
products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or
information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes.
No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability
for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or
materials, except as may be provided in Skyworks’ Terms and Conditions of Sale.
THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR
OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY
INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR
COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR
ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT
LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT
OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks
products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such
applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale.
Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of
design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating
safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any
equipment resulting from the use of Skyworks products outside of Skyworks’ published specifications or parameters.
Skyworks, the Skyworks symbol, Sky5®, SkyOne®, SkyBlue™, Skyworks Green™, Clockbuilder®, DSPLL®, ISOmodem®, ProSLIC®, and SiPHY®are trademarks or
registered trademarks of Skyworks Solutions, Inc. or its subsidiaries in the United States and other countries. Third-party brands and names are for
identification purposes only and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at
www.skyworksinc.com, are incorporated by reference.
Portfolio
www.skyworksinc.com
Quality
www.skyworksinc.com/quality
Support & Resources
www.skyworksinc.com/support
Connecting Everyone
and Everything,
All the Time
Skyworks Solutions, Inc. | Nasdaq: SWKS | [email protected] | www.skyworksinc.com
USA: 781-376-3000 | Asia: 886-2-2735 0399 | Europe: 33 (0)1 43548540 |