Sleep Candy AF-201TXL User manual

Adjustable Bed
Manual
AF-201TXL/201Q
Product Specifications:
Product Size:
Twin XL: 38” x 80” (96.5 x 203 cm)
Queen: 60” x 80” (152 x 203 cm)

Safety Precautions:
Please read all directions before using the bed, and retain this guide for reference.
Input voltage: AC 100-240 . 50/60HZ, output: DC29 2.0A.
Unplug the bed before cleaning it.
Keep the product wire, power supply, and control box away from heat.
Do not use the bed in a humid environment. The connector part of the wire and the
gap between the motor and the control box cannot be exposed to liquid or high
humidity.
Never operate the bed if it has a damaged cord or plug, or is not working properly.
Unplug the power cord and remove the remote control battery when the bed is not
being used for a prolonged period of time.
Consult your physician if you have any health questions regarding the use of this
product.
Do not let children play with or operate the bed.
Do not allow children or pets underneath the bed.
Parts List:
Bed Platform x 1 pc Mattress Rail x 1 pc Legs x 4 pcs
Remote Control x 1 pc Power Supply Box x 1 pc Power Cable x 1 pc

Assembly:
1. Lay the carton flat on the floor and carefully cut it open.
2. Lift the carton so that the open side faces down and slide it up and off the bed.
Place the bed upside-down flat on the floor.
3. Remove and discard the plastic bag. Put together the two pieces of the bed and
align them flat on the floor.
4. Cut the zip ties, take out all the part boxes and the mattress rail, and check that
you have all the necessary parts according to the parts list.
5. For leg assembly push the screw through the triangular brace. Screw in the leg
and tighten.
6. Connect the 01-connector from the controller to the 01-plug of the power supply.
Connect the 8-wire plug of the power cable to the other jack on the switch’s power
supply. Connect the power cable to your nearby power outlet.
7. Insert batteries into the remote control. Press the first circled button. If the motor
begins to run, unplug the power supply and turn the bed over to its right side-up
position. If the motor does not run, it needs to re-match its code.
Matching code: Press the two buttons in the circles shown and at the same time
press the little button on the side of the control box until you hear the 'didi' sound.

8. Insert the mattress rail at the foot of the bed. The bed is now ready for use.
Remote Control unctions

Button Operation
Press and hold to raise the
backrest. Let go when the
desired position is reached.
Press and hold to raise the
footrest. Let go when the
desired position is reached.
Press and hold to lower the
backrest. Let go when the
desired position is reached.
Press and hold to lower the
footrest. Let go when the
desired position is reached.
Click to set a user-defined
position.
Click to flatten the bed.
Click to turn the LED flashlight
on top of the remote on and off.
Memory Setting:
Setting a memory position if you’re not satisfied with the factory setting.
1. Press the FLAT button to flatten the bed.
2. Adjust the bed to your preferred position by pressing the head and foot up/down
buttons.
3. Press and hold button M and let go after you hear the “didi” sound that indicates
the setting has been successfully programmed.
Emergency Reset:
If you temporarily cannot reach the remote control, press the little button at the side
of control box, or the little button on the extension wire to return the bed to the flat
position.

Power Outage:
When the power fails, the function of the backup battery is to restore the bed to a flat position.
1. Open the power box and install the appropriate battery.
2. Use the remote control to return the bed to a flat sleeping position until power returns.
3. Once power returns replace the battery if needed.
Troubleshooting:
If you experience problems with your adjustable bed, please follow these steps:
1. Press any button on the remote control to see whether the blue backlight is bright.
If it’s dim or does not light, check the battery.
2. Check the green power indicator light on the power supply. If it’s not lit, check the
power outlet.
3. Check for loose wires or connectors.
4. Check if the adjustable beds assembled according to the above steps.
If your problems cannot be solved by the above steps, please contact us.
Thank you for purchasing our adjustable bed.
Sleep Candy Inc.