Sloan MH-2000 User manual

10500 Seymour Ave Franklin Park, IL 60131 | Phone: [phone] | Fax: [phone] | Sloan.com
Copyright © 2020 Sloan. All rights reserved.
Page: 1 of 13
Installation Instructions
Code #: 0816883 Rev 2 (01/21)
Sloan Mobile Handwashing Station
MH-2000 Installation and Operation Instructions
Limited Warranty
Unless otherwise noted, Sloan Valve Company warrants its Mobile Handwashing Sink to be made of rst class materials, free from defects
of material or workmanship under normal use and to perform the service for which it is intended in a thoroughly reliable and efcient
manner when properly installed and serviced, for a period of one year from date of purchase. During this period, Sloan Valve Company
will, at its option, repair or replace any part or parts which prove to be thus defective if returned to Sloan Valve Company, at customer’s
cost, and this shall be the sole remedy available under this warranty. This warranty covers enclosure framing, panels, countertop material
and attachments. It does limit or extend individual product component warranties provided by the component manufacturer. No claims
will be allowed for labor, transportation or other incidental costs. This warranty extends only to persons or organizations who purchase
Sloan Valve Company’s products directly from Sloan Valve Company for purpose of resale. This warranty does not cover the life of the
batteries.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO EVENT IS SLOAN VALVE COMPANY
RESPONSIBLE FOR ANY CONSEQUENTIAL DAMAGES OF ANY MEASURE WHATSOEVER.

10500 Seymour Ave Franklin Park, IL 60131 | Phone: [phone] | Fax: [phone] | Sloan.com
Copyright © 2020 Sloan. All rights reserved.
Page: 2 of 13
Installation Instructions
Code #: 0816883 Rev 2 (01/21)
Parts List
Description Item Number Quantity
Panel, Lower Front 1 1
Panel, Left 2 1
5AH Li-Ion Battery 3 1
5 Gallon Water Bottle 4 2
Battery Charger (Not Shown) 5 1
1/4” Hex Key (Not Shown) 6 1
Paper Towel Key (Tool) (Not Shown) 7 1
Trash Bag Holder (Not Shown)
For standard 13 gallon draw-string trash bag, see spare parts list for details. 8 1
5 Gallon Water Bottle Holder 9 1
Figure 1
1) Panel, Front
2) Panel, Left
3) Battery
4) 5 Gallon Water Bottles
9) 5 Gallon Water Bottle Holder

10500 Seymour Ave Franklin Park, IL 60131 | Phone: [phone] | Fax: [phone] | Sloan.com
Copyright © 2020 Sloan. All rights reserved.
Page: 3 of 13
Installation Instructions
Code #: 0816883 Rev 2 (01/21)
Component / Description
Component Description
Soap Dispenser GOJO CS-8
Paper Towel Dispenser EnMotion Impulse Auto Paper Towel Dispenser, White
Faucet Sloan SF2250 Gooseneck Faucet
Battery Milwaukee 5AH Li-Ion Battery
5 Gallon Water Bottle Empty 5 Gallon Water Bottle
Water Bottle Holder 5 Gallon Water Bottle Holder (Holds two 5 gallon water bottles)
Access Panel - Right Hinged
Access Panel - Front Removable
Access Panel - Left Removable
Waste Tank 16 Gallon Waste Tank
Pull Handle Handle for moving unit around facility
Battery Capacity Indicator Displays battery level of unit
AC Power In 3 Prong Twist Lock
Water Supply In 3/4” garden hose connection
Waste Water Out 3/4” garden hose connection
AC / DC On/Off 3 way toggle switch, center off
Main Power Switch On/Off Main power switch to the Mobile Handwashing Sink
Drain Pump Switch On/Off Supplies power to the drain pump
Mobile Handwashing Sink Component Layout
Figure 2
Paper Towel DispenserSoap Dispenser
Faucet
Battery
Water Supply In
Waste Water Out
(Gravity Fed)
Rear View
Panel, Right
(Hinged)
Panel, Left
(Removable)
Battery Capacity Indicator
Water Supply Pump
Pull Handle
Waste Tank
AC Power In
Waste Water Out
(Pump)
Front View
Note: Front panel not shown for clarity.
A-A
AC / DC On/Off
Main On/Off
Drain Pump
On/Off
Right Side View
Battery
A
A
Bottle Holder (Hinged)
(5 Gal Water Bottles
Not Shown for Clarity)

10500 Seymour Ave Franklin Park, IL 60131 | Phone: [phone] | Fax: [phone] | Sloan.com
Copyright © 2020 Sloan. All rights reserved.
Page: 4 of 13
Installation Instructions
Code #: 0816883 Rev 2 (01/21)
Initial Setup Prior to First Use
IMPORTANT
(Must be completed before initial power up and water connection)
• Use holding tank cleaner/treatment for 16 gallon waste tank.
• Sanitation of the fresh water pump (if applicable) must be completed prior to initial use.
• Batteries for the paper towel dispenser are shipped loose and must be installed prior to initial use.
• Soap bottle is shipped loose and must be installed prior to initial use.
This mobile handwashing sink has multiple options for power, water supply, and drainage. See below.
Power
• AC Power
–Select this option when power can be supplied by an external source.
• DC Power (If applicable)
–Select this option when external power is not available, and battery power is required.
Water Supply
• External Water Supply
–Select this option when external water connection is available, this option can be connected via a 3/4”
garden hose.
• 5 Gallon Water Supply (If applicable)
–Select this option when external water connection is not available, two 5 gallon water bottles are required.
Drainage
• Manual (Gravity fed)
–Select this option if no power is available to the unit. This option is controlled by a ball valve.
• Electric Pump
–Select this option select this option if AC or DC power has been select, this option is controlled by a switch.
–Select this option if waste needs to be pumped up hill or over a long distance.
Faucet:
• Refer to detailed SF-2250 instructions available via Sloan.com for the following:
–Sensor calibration (If required)
Note: Failure to properly calibrate the faucet sensor may lead to unexpected activation and increase
maintenance intervals.
–Priming
–Battery battery replacement
–Care and cleaning
Soap Dispenser:
• Refer to detailed CS-8 instructions available via GOJO.com for the following:
–Installation of replacement soap bottle and battery (Shipped together)
–Care and cleaning
Paper Towel Dispenser:
• Refer to EnMotion manufacturer instructions for the following:
–Installation of batteries (Included, shipped loose)
–Paper towel installation
–Paper length setting
–Care and cleaning
Fresh Water Pump:
• Refer to detailed instructions available via Xylem.com for the following:
–Sanitize unit prior to rst use.
–Routine sanitation must occur as required, minimum 6 times per year.
16 Gallon Waste Tank
• Sanitation of Grey Water Tank
–The 16 Gallon grey water tank must be treated to break down waste and eliminate odors. Using a liquid
holding tank cleaner/treatment, follow the holding tank cleaner instructions for cleaning or treatment of grey
water holding tank. For best results, clean and ush the tank weekly regardless of the water level or usage.
Recommend using a formaldehyde-free formulation that is safe for all pipes including PVC. Routine treatment
is an important step to ensure reliable service.

10500 Seymour Ave Franklin Park, IL 60131 | Phone: [phone] | Fax: [phone] | Sloan.com
Copyright © 2020 Sloan. All rights reserved.
Page: 5 of 13
Installation Instructions
Code #: 0816883 Rev 2 (01/21)
Setting Up for External Water Supply In and Waste Water Out
Figure 3
Water Supply in
Waste Water Out
(Gravity Fed)
Waste Water Out
(Pump)
1. Connect to water supply in.
a. Make sure that the external water is OFF
b. Using a standard 3/4” garden hose or equivalent, connect to an external water supply.
c. Connect the opposite end of the hose to the Water Supply In on the middle, rear panel of the Mobile
Handwashing Sink.
d. Make sure that connection is tight and does not leak.
2. Connect to waste line out (Gravity Fed).
a. Using a standard 3/4” garden hose or equivalent, connect to the Waste Line Out on the bottom, rear
panel of the Mobile Handwashing Sink.
b. Make sure that connection is tight and does not leak.
c. Place the opposite end of the hose in an appropriate area for draining waste water tank.
3. Connect to waste line out (Pump).
a. Make sure that the gravity fed ball valve is in the closed position.
b. Using a standard 3/4” garden hose or equivalent, connect to the Waste Line Out on the bottom, rear
panel of the Mobile Handwashing Sink.
c. Make sure that connection is tight and does not leak.
d. Place the opposite end of the hose in an appropriate area for draining waste water tank.

10500 Seymour Ave Franklin Park, IL 60131 | Phone: [phone] | Fax: [phone] | Sloan.com
Copyright © 2020 Sloan. All rights reserved.
Page: 6 of 13
Installation Instructions
Code #: 0816883 Rev 2 (01/21)
Connect the AC Power In
Figure 4
AC Power In
WARNING - Risk of Electric Shock. Connect Only to a Supply Protected by a Ground-Fault Circuit-Interrupter (GFCI).
1. Plug a 12/3-Prong NEMA L5-20 AMP 125V Power cord (Not supplied) into twist lock AC Power In receptacle
on the rear panel of the Mobile Handwashing Sink, and connect the opposite end to a matching NEMA L5-
20R twist-lock receptacle (120V/20A).
Note:
Strain Relief - UL 1951, Clause 10.4 and C22.2 No. 68, Clause 5.6 - A exible cord shall be provided with a means
to reduce the transmittal of tensional or rotational force from the cord to the wiring connections. A detachable
exible power supply cord will be permitted for the 120 VAC powered Hand Washing Stations if the appliance
inlet is a twist-lock design.

10500 Seymour Ave Franklin Park, IL 60131 | Phone: [phone] | Fax: [phone] | Sloan.com
Copyright © 2020 Sloan. All rights reserved.
Page: 7 of 13
Installation Instructions
Code #: 0816883 Rev 2 (01/21)
Operation Instructions AC Power
Figure 5
Paper Towel DispenserSoap Dispenser
Faucet
Battery
Panel, Right
(Hinged)
Bottle Holder (Hinged)
(5 Gal Water Bottles
Not Shown for Clarity)
Panel, Left
(Removable)
Pull Handle
Waste Tank
Supply Water Pump
Front View
Note: Front panel not shown for clarity.
A-A
AC / DC On/Off
Main On/Off
Drain Pump
On/Off
Right Side View
Battery
A
A
1. Position the Mobile Handwashing Sink where needed.
2. Lock each caster in place to secure the Mobile Handwashing Sink in place.
a. Press down on the lock lever for each caster until the lever locks into place and the caster no longer
rotates freely.
b. To release the lock lever, press up on each lock lever until the lever locks in the open position and the
caster rotates freely.
3. Connect external water supply in and the waste line out.
4. Plug a 12/3-Prong NEMA L5-20 AMP 125V Power cord (Not supplied) into twist lock AC Power In receptacle
on the rear panel of the Mobile Handwashing Sink, and connect the opposite end to an 110 VAC power
source.
5. Using AC Power.
a. Position the AC / DC Switch to the AC position.
b. Position the Main On/Off Switch in the on position.
c. If using the electric drain pump option, position the drain pump switch in the On position.
6. When using the Mobile Handwashing Sink for the rst time, prime the sensor faucet by moving your hand in
front of the faucet sensor to prime the water lines.
The Mobile Handwashing Sink is ready for use.
7. Drain Waste Tank when above half full.
a. Periodically remove or open an access panel to check the waste tank water level. If the waste tank
water level is more than half full, drain the waste tank.
8. Set all switches to the off position when not in use

10500 Seymour Ave Franklin Park, IL 60131 | Phone: [phone] | Fax: [phone] | Sloan.com
Copyright © 2020 Sloan. All rights reserved.
Page: 8 of 13
Installation Instructions
Code #: 0816883 Rev 2 (01/21)
Operation Instructions DC (Battery) Power
Figure 6
Paper Towel DispenserSoap Dispenser
Faucet
Battery
Panel, Right
(Hinged)
Bottle Holder (Hinged)
(5 Gal Water Bottles
Not Shown for Clarity)
Panel, Left
(Removable)
Pull Handle
Waste Tank
Supply Water Pump
Front View
Note: Front panel not shown for clarity.
A-A
AC / DC On/Off
Main On/Off
Drain Pump
On/Off
Right Side View
Battery
A
A
1. Position the Mobile Handwashing Sink where needed.
2. Lock each caster in place to secure the Mobile Handwashing Sink in place.
a. Press down on the lock lever for each caster until the lever locks into place and the caster no longer
rotates freely.
b. To release the lock lever, press up on each lock lever until the lever locks in the open position and the
caster rotates freely.
3. Connect external water supply in and the waste line out.
4. Using DC (Battery) Power.
a. Position the AC / DC Switch to the DC position.
b. Position the Main On/Off Switch in the on position.
5. If using the electric drain pump option.
a. Position the drain pump switch in the On position.
Note: Make sure battery is fully charged prior to use. Recharge battery as needed, minimum once daily.
6. When using the Mobile Handwashing Sink for the rst time, prime the sensor faucet by moving your hand in
front of the faucet sensor to prime the water lines.
The Mobile Handwashing Sink is ready for use.
7. Drain Waste Tank when above half full.
a. Periodically remove or open an access panel to check the waste tank water level. If the waste tank
water level is more than half full, drain the waste tank.
8. Set all switches to the off position when not in use.
Note: AC/DC Switch, select the center position.

10500 Seymour Ave Franklin Park, IL 60131 | Phone: [phone] | Fax: [phone] | Sloan.com
Copyright © 2020 Sloan. All rights reserved.
Page: 9 of 13
Installation Instructions
Code #: 0816883 Rev 2 (01/21)
Install 5 Gallon Water Bottles
Figure 7
4
Notes:
1. 5 gallon water bottles are not supplied.
2. Use care when placing the bottles in to the bottle holder.
Do not allow bottles to splash inside the unit.
1. If not using an external water source, install two, 5 Gallon Water Bottles (4) into the water bottle platform.
a. Fill the two 5 Gallon Water Bottles with potable water.
b. Tilt the water bottle platform as shown.
c. Insert two, lled, 5 Gallon Water Bottles (4) onto the water bottle platform.
d. Tilt water bottle platform back to the original position.
2. Insert water line into 5 Gallon Water Bottle (4).
a. Remove cap from 5 Gallon Water Bottle (4).
b. Insert suction wand that is attached to the supply water pump.
c. Make sure the power switch on the water supply pump is in the ON position.
3. Remove water line from the empty 5 Gallon Water Bottle (4) and repeat step 2 with new/full 5 gallon water
bottle. DO NOT let the water line come into contact with any object during transfer.
Note: If bottle runs empty, oat switch will shut off the unit.
4. When 5 Gallon Water Bottle (4) are empty, re-ll with potable water. Repeat step 1. Refer to the Care and
Maintenance section (page 12) for cleaning instructions.

10500 Seymour Ave Franklin Park, IL 60131 | Phone: [phone] | Fax: [phone] | Sloan.com
Copyright © 2020 Sloan. All rights reserved.
Page: 10 of 13
Installation Instructions
Code #: 0816883 Rev 2 (01/21)
Draining the Waste Water Tank (Gravity Fed)
Figure 8
SEE DETAIL A DETAIL A
Waste Line Ball Valve
(Open Position)
Waste Line Ball Valve
(Closed Position)
1. Drain the waste tank (Gravity Fed).
a. Make sure that waste line hose is connected to waste line out (Gravity Fed Location, Figure 3. page
5) at the bottom rear panel of the Mobile Handwashing Sink.
b. Make sure that the opposite end of the waste line hose is in an appropriate location to drain the waste
water tank. 16 gallons minimum drainage.
c. Use the 1/4” Hex Key (Included). unlock the cam latch on the right access panel. Open the right side
access panel.
d. Locate the waste line ball valve and turn a 1/4 turn to open the valve.
e. Close the waste line ball valve when waste water tank is empty.
f. Close and latch the right access panel.

10500 Seymour Ave Franklin Park, IL 60131 | Phone: [phone] | Fax: [phone] | Sloan.com
Copyright © 2020 Sloan. All rights reserved.
Page: 11 of 13
Installation Instructions
Code #: 0816883 Rev 2 (01/21)
Draining the Waste Water Tank (Electric Pump)
Figure 9
SEE DETAIL B
Right Side
DETAIL B
Waste Pump
On/Off Switch
Main
On/Off Switch
1. Drain the waste tank (Electric Pump).
a. Make sure that waste line hose is connected to waste line out (Pump Location, Figure 3. page 5) at
the bottom rear panel of the Mobile Handwashing Sink.
b. Make sure that the opposite end of the waste line hose is in an appropriate location to drain the waste
water tank. 16 gallons minimum drainage.
c. Use the 1/4” Hex Key (Included). unlock the cam latch on the right access panel. Open the right side
access panel.
d. Locate the Main On / Off Switch and toggle to the On position.
e. Locate the Waste Pump On Off Switch and toggle to the On position.
f. Toggle Waste Pump Switch to the Off position when the waste tank is empty.
Note: Failure to turn the waste water pump off when the tank is empty can damage the pump or cause
premature pump failure.
g. Close and latch the right access panel.

10500 Seymour Ave Franklin Park, IL 60131 | Phone: [phone] | Fax: [phone] | Sloan.com
Copyright © 2020 Sloan. All rights reserved.
Page: 12 of 13
Installation Instructions
Code #: 0816883 Rev 2 (01/21)
Notes:
1. Frequency may vary per actual daily use.
2. Recharge battery daily, regardless of use. Make sure that battery is fully charged prior to each use.
3. Empty and treat waste water tank weekly, regardless of use.
Suggested Usage Schedule
Description Unit of Measure Frequency
Fresh Water 5gal Bottle 3 per Day
Waste Water 16 gal Tank Drain Daily
Battery Charge Full Charge Daily
Soap Rell Rell 2 per Day
Paper Towel Rell Roll Daily
Additional guidance for surface care and maintenance can be found at:
https://www.corian.com/IMG/pdf/k-29810_corian_solid_surface_care_and_maintenance_for_facility_
managers.pdf
Lubrication
Periodically apply silicone or oil lubricant to moving parts such as casters and hinges for smooth operation and
protection.
5 Gallon Water Bottle Sanitation
Clean the fresh water jugs regularly by either of these options:
1. Steramine ® multi-purpose sanitizer.
2. A mixture of 10% bleach, 90% water.
Once clean, rinse the tanks with fresh water.
WARNING:
Do not run bleach or any other liquid other than fresh, clean water through the plumbing system. Failure to
comply may cause damage to components.
Care and Maintenance
DuPont Corian®Surface Care
Most Dirt & Residue
Use soapy water or ammonia-based cleaner (not window cleaner), rinse
and wipe completely dry. Commercially available solid surface cleaners
such as Clean EnCounters® also works well.
Preventing Hard Water Marks Rinse and wipe completely dry after cleaning. Clean spills before they dry.
Removing Hard Water Marks Use cleaner formulated for removing hard water such as CLR® or Lime-A-
Way®
Disinfecting
Occasionally wipe surface with diluted household bleach – 1:100 (5 Tbsp.
of bleach to 1 gallon of water, as recommended by the CDC for disinfec-
tion of surfaces.
WARNING
DO NOT operate or store Mobile Hand Washing Station below freezing temperatures. Damage to internal
components may occur.

10500 Seymour Ave Franklin Park, IL 60131 | Phone: [phone] | Fax: [phone] | Sloan.com
Copyright © 2020 Sloan. All rights reserved.
Page: 13 of 13
Installation Instructions
Code #: 0816883 Rev 2 (01/21)
Spare Parts List
Item No. Code No. Description
1A 3362144 Sloan® SF-2250-Gooseneck Faucet
1B 0365420 0.5 GPM Aerator for Sloan® SF-2250 Faucet
2A 0383300 PURELL® CS8 Soap Dispenser
2B 0383301 PURELL® CS8 1200 mL HEALTHY SOAP® rell, 2pk.
3 0383332 Georgia Pacic® enMotion® Impulse® Automatic Paper Towel Dispenser, White
4 0383505 Pull Handle
5 0383390 Trash bag Holder
6 0383518 Graphic Label Kit
7 0365036PK Sloan® ETF-460A Grid Strainer
8A 0108620 Milwaukee® M18™ REDLITHIUM™ XC5.0 Extended Capacity Battery Pack, Cat.
No. 48-11-1850
8B 0383352 Milwaukee® M18™ & M12™ Rapid Charger, Cat. No. 48-59-1808
9 3830010 MH PANEL ASM-UPPER FRONT W/ DISPLAY
10 3830009 MH PANEL ASM-LOWER FRONT
11 3830006 MH PANEL ASM-LEFT
12 3830007 MH PANEL ASM-RIGHT
1A
1B
2A, 2B
3
4
5
78A, 8B
6
9
10 11 12
Illustrated Spare Parts List