Sloan WES-7000 User manual

CARRIER STUD PLACEMENTI if using
in-wall carrier, setbearing rods as
shown above.
SET DRAIN LINE HEIGHT 17”from
finished floor (standard 24” rim) or 10” for
ADA installation. Threadednipple should
extend½ to ¾”from wall.
A. Clean face of existing drain nipple.
B. Install the clear inspection disc with
compression nut.
C. Slowly pour water into the drain.
D. Use a flashlight to check the pitch/
slope. No water should be present in
the inspection disc or nipple.
E. Remove disc and nut after inspection.
"
DRILL HOLES masonry
bit for the lower anchor screws
and mounting plate and insert
plastic anchors where indicated.
TIGHTEN COMPRESSION
NUT AND HOSE CLAMP.
DETERMINE THE DRAIN NIPPLE DEPTH
by measuring the distance between the
back of the sanitary tee (or elbow) to
the front edge of the nipple.
MEASURE & MARK THE ROUGH-IN if
"
masonry bit to drill hole, then install
the hangerbracket with one plastic
anchor and screw.
"
ADJUST DRAIN TO ACHIEVE PITCH
only if standing water is present
(code requires ¼” drop per foot of
drain line for proper pitch). Seal wall
according to code.
A. Hang the bowl on the bracket and checktail
pipe alignment, then remove the bowl and
adjust the bracket as needed.
Re-hang and re-check bowl alignment with
the drain line. Tail pipe should align with center
of drain line.
B. Mark anchor holes then
remove bowl without
moving hangerbracket.
INCORRECT
Not centered
CORRECT
Centered
A B
½" to ¾"
10" for ADA
installation
standard 24" rim
finished floor
17"
2¼
1⁄
1 "
13 ⁄ "
Drain
Cut away wall
Lift drain line & brace
with mending plate
Install two
additional screws
A. Find the drain nipple depthon
the Tube Cutting Chart (left).
Measure and mark the specified
trim length on the insert tube at
the nearest ¼” groove.
B. Cut the tube at the groove using a sharp
utility knife to ensure a square, flat cut.
C. Clean burrs from the cut end by using
emery paper.
D. Apply lubricant to the outside of the
rubberbushing and ribbed inside area.
E. Insert thetube andbushing with arrow
tab at the top. Apply lubricant to tailpipe
of housing. IMPORTANT: Be sure arrow tab
is at 12:00 position.
1234
Arrow
tab UP
1234
A
C
BDE
POUR 5
GALLONS
OF WATER
as rapidly
as possible
into housing
to ensure
good flow
and no leaks or
standing water.
CAULK THE BOWL
TO THE WALLif
there isgoodflow
andno leaks or
standing water.
INSTALL
CARTRIDGE
per the cartridge
instruction sheet.
CARTRIDGE
INSTRUCTIONS
HANG THE BOWL, inserting tailpipe
into bushing, then install anchor
screws with washers.
PLACE THE HOSE CLAMP
and compression nut onto the
housing tailpipe.
13 ⁄ "
Install plastic anchor
and screw here
14 15
4
13
3
12
8
6
2
10 11
75
1
C D
9
WES-7000 WATERFREE URINAL
NEW CONSTRUCTION
INSTALLATION INSTRUCTIONS
BEFORE STARTING INSTALLATION:
IMPORTANT Do not install on copper DWV
due to copper’s susceptibility to corrosion.
Check rough-in height to achieve 24” rim height
(17” rim height for ADA).
Check slope. Downhill slope, per code, is essential
because waterfree urinals depend on gravity flow.
Check DWV material. Suitable materials include
cast iron, PVC, ABS and galvanized steel.
TUBE CUTTING CHART
Measure drain nipple depth (inches) to find trim
length (inches)
13 7/8” or more DO NOT CUT
3 3/4” or less DO NOT USE TUBE
•
•
•
•
•
•
OR LESS TRIM
13 ¾" ¼"
13 ½ ½
13 ¼ ¾
13 1
12 ¾ 1¼
12 ½ 1½
12 ¼ 1¾
12 2
11 ¾ 2¼
11 ½ 2½
11 ¼ 2¾
11 3
10 ¾ 3 ¼
10 ½ 3 ½
OR LESS TRIM
10 ¼" 3 ¾"
10 4
9 ¾ 4 ¼
9 ½ 4 ½
9 ¼ 4 ¾
95
8 ¾ 5 ¼
8 ½ 5 ½
8 ¼ 5 ¾
86
7 ¾ 6 ¼
7 ½ 6 ½
7 ¼ 6 ¾
77
OR LESS TRIM
6 ¾" 7 ¼"
6 ½ 7 ½
6 ¼ 7 ¾
68
5 ¾ 8 ¼
5 ½ 8 ½
5 ¼ 8 ¾
59
4 ¾ 9 ¼
4 ½ 9 ½
4 ¼ 9 ¾
410
CUSTOMERSERVICE
1-888-SLOAN-14 (1-888-756-2814)
[email protected]
www.sloanvalve.com
The information in this document is subject to change without notice.
© 2015 Sloan Valve Company All rights reserved. (08-15)Rev1
CAUTIONAfter removing any urinal from the
drainline, it’s normal for certain naturally occurring,
but potentially hazardous sewer gases to escape
through the opening until the waterless cartridge
is installed properly into the waterless urinal. If you
need to leave an open drain line unattended after
removing the urinal from the wall, temporarily wedge paper towels or a
rag into the drainhole to reduce any outflow of sewer gases, and remove
the paper towels or rag prior to completing the urinal or cartridge
installation. Never smoke, have an open flame, or place your nose or
mouth near open drain lines or waterless urinal housings into which
a cartridge is not yet properly installed. You alsocan wear abreathing
mask when removing or installing any waterless urinal or cartridge to
reduce potential exposure to any such gases.
•
LUBRICANT
in-wall carrier is not used. Use a
11 10
12

if in-wall carrier is not used. Use a
masonry bit to drill hole, then install
A. Hang the bowl on the bracket and checktail
pipe alignment, then remove the bowl and
adjust the bracket as needed.
Re-hang and re-check bowl alignment with
the drain line. Tail pipe should align with center
of drain line.
B. Mark anchor holes then
remove bowl without
moving hangerbracket.
A. Findthe drain nipple depthon
the Tube Cutting Chart (left).
Measure and mark the specified
trim length on the insert tube at
the nearest ¼” groove.
B. Cut the tube at the groove using a sharp
utility knife to ensure a square, flat cut.
C. Clean burrs from the cut end by using
emery paper.
D. Apply lubricant to the outside of the
rubberbushing and ribbedinside area.
E.Insert thetube and bushing with arrow
tab at the top. Applylubricant to tailpipe
of housing. IMPORTANT: Be sure arrow tab
is art 12:00 position.
USE UTILITY KNIFE TO CUT CAULK then
use a putty knife and mallet to remove
the bowl. Remove hangerbrackets,
scrape o caulk, and clean the wall.
MEASURE & MARK THE ROUGH-IN
"
the hangerbracket with one plastic
anchor and screw.
DETERMINE THE DRAIN NIPPLE DEPTH
by measuring the distance between the
back of the sanitary tee (or elbow) to the
front edge of the nipple.
IMPORTANT: Use adrain machine to
remove build-up inside pipes. Clean up
to 25 feet deep then flush with water to
remove cutting debris. Never install on
copper DWV.
A. Clean face of existing wall flange.
B. Install the brass ange with the clear
inspection disc.
C. Slowly pour water into the drain.
D. Use a ashlight to check the pitch/
slope. No water should be present in
the inspection disc or nipple.
E. Remove ange and disc after inspection.
ADJUST DRAIN TO ACHIEVE PITCH
only if standing water is present
(code requires ¼” drop per foot of
drain line for proper pitch). Seal wall
according to code.
PLACE THE SEAL INTO THE FLANGE with
the ribs facing out. Install the flange
with washers and hex nuts, but do not
tighten completely.
HANG THE BOWL, inserting
tailpipe into bushing, then
install anchor screws with
washers.TIGHTEN FLANGE
BOLTS AND HOSE CLAMP.
POUR 5
GALLONS
OF WATER
as rapidly
as possible
into housing
to ensure
good flow
and no leaks or
standing water.
INSTALL THE HOSE CLAMP
with screw head at bottom,
but do not tighten.
CAULK THE BOWL
TO THE WALL if
there isgoodflow
andno leaks or
standing water.
INSTALL
CARTRIDGE
per the cartridge
instruction sheet.
2" side cutter blade
Cut away wall
Lift drain line & brace
with mending plate
13 ⁄ "
Install plastic anchor
and screw here
INCORRECT
Not centered
CORRECT
Centered
11 10
12
CARTRIDGE
INSTRUCTIONS
1234
Arrow
tab UP
1234
A
C
BDE
"
14 15
4
13
3
12
8
6
2
10 11
9
75
1
C D
A B
WES-7000 WATERFREE URINAL
RETROFIT
INSTALLATION INSTRUCTIONS
BEFORE STARTING INSTALLATION:
IMPORTANT Do not install on copper DWV
due to copper’s susceptibility to corrosion.
Check rough-in height to achieve 24” rim height
(17” rim height for ADA).
Check slope. Downhill slope, per code, is essential
because waterfree urinals depend on gravity flow.
Check DWV material. Suitable materials include
cast iron, PVC, ABS and galvanized steel.
Shut o water supply and cap the nipple with 3/4“
chrome cap (provided).
TUBE CUTTING CHART
Measure drain nipple depth (inches) to find trim
length (inches)
13 7/8” or more DO NOT CUT
3 3/4” or less DO NOT USE TUBE
•
•
•
•
•
•
OR LESS TRIM
13 ¾" ¼"
13 ½ ½
13 ¼ ¾
13 1
12 ¾ 1¼
12 ½ 1½
12 ¼ 1¾
12 2
11 ¾ 2¼
11 ½ 2½
11 ¼ 2¾
11 3
10 ¾ 3 ¼
10 ½ 3 ½
OR LESS TRIM
10 ¼" 3 ¾"
10 4
9 ¾ 4 ¼
9 ½ 4 ½
9 ¼ 4 ¾
95
8 ¾ 5 ¼
8 ½ 5 ½
8 ¼ 5 ¾
86
7 ¾ 6 ¼
7 ½ 6 ½
7 ¼ 6 ¾
77
OR LESS TRIM
6 ¾" 7 ¼"
6 ½ 7 ½
6 ¼ 7 ¾
68
5 ¾ 8 ¼
5 ½ 8 ½
5 ¼ 8 ¾
59
4 ¾ 9 ¼
4 ½ 9 ½
4 ¼ 9 ¾
410
CUSTOMERSERVICE
1-888-SLOAN-14 (1-888-756-2814)
[email protected]
www.sloanvalve.com
The information in this document is subject to change without notice.
© 2015 Sloan Valve Company All rights reserved. (08-15)Rev1
CAUTIONAfter removing any urinal from the
drainline, it’s normal for certain naturally occurring,
but potentially hazardous sewer gases to escape
through the opening until the waterless cartridge
is installed properly into the waterless urinal. If you
need to leave an open drain line unattended after
removing the urinal from the wall, temporarily wedge paper towels or a
rag into the drainhole to reduce any outflow of sewer gases, and remove
the paper towels or rag prior to completing the urinal or cartridge
installation. Never smoke, have an open flame, or place your nose or
mouth near open drain lines or waterless urinal housings into which
a cartridge is not yet properly installed. You alsocan wear abreathing
mask when removing or installing any waterless urinal or cartridge to
reduce potential exposure to any such gases.
•
LUBRICANT
Install two
additional screws
•
DRILL HOLES masonry bit for the
lower anchor screws and mounting plate
and insert plastic anchors where indicated.