SmallRig Forevala W60 User manual

Wireless Microphone
User Manual
Drahtloses Mikrofon
Benutzerhandbuch
无线麦克风
用户手册

Preface
Thank you for purchasing SmallRig's products.
Important Notes
Please read this User Manual carefully.
Do not use the product in water because it is not dust or water
proof.
Do not let the product fall to the ground, be hit or suffered violent
impact.
Do not exert pressure on its LCD screen because over pressure will
cause permanent damage to the screen.
Do not use the product in the completely closed environment, or
it may lead to rise of internal temperature, which causes product
failure, ignition or other accident.
Do not leave the product in excessive heat, high temperatures can
cause the product to malfunction.
Do not place the product in a place where there are corrosive
chemical to protect the product from corrosion,corrosion may
cause the product to malfunction.
Do not place the product nearby any combustible or volatile
solution, or it may cause a fire disaster or smog.
Be sure to power the product off when it is not in use.
Use only a microfiber and dry cloth for cleaning the product.

Never remove the non-detachable lithium battery without
permission.
When the battery is not in use for a long time, please charge and
discharge the battery each 6-month, and provide it with
approximately 60% of the electric quantity to prolong its lifetime.
Since there are some hazardous substances in the battery, please
do not discard it. Instead, dispose of the product that is damaged
or will never be used according to the waste management
measures.
Note: To prolong the lifetime, please minimize the use of the
product while charging.
Warning
Please do not disassemble the product. If you suspect any
problem with the product, please contact the purchasing
platform and apply for after-sales treatment.
Standard Use of the Equipment
The standard use of the SmallRig Forevala W60 wireless
microphone includes
Read this manual carefully, especially the "Important Notes"
section.
Use and store the product under the working conditions specified
in this manual.

In the Box
Transmitter (TX)
Receiver (RX)
Storage Case
TRS to TRS Cable
TRS to TRRS Cable
Furry Windscreen
USB-C Charging Cable
SmallRig Metal Sticker
Carrying Bag
User Manual
Product Details
Transmitter

Transmitter Screen
① Microphone: built-in condenser microphone
② 3.5mm port: TRS external microphone jack
③ USB-C port: 5V charging port
④ Display: interactive LCD display
⑤ Power button: short press to mute on, long press to switch
on and off
⑥ Pairing key: short press low cut on, long press to pair
① Mute / Microphone works normally
② Signal intensity
③ Low cut function enabled
④ Transmitter battery power
⑤ Microphone audio bar of channel A / B

Operations
1.Switch button: long press to power on / off. "SmallRig" logo
appears on the LCD screen after power on. In power on mode,
short press to enter mute mode, and short press again to enter
normal mode.
2.Low cut function: short press the low-cut button to turn on / off
the low-cut function. When the low cut function is turned on, the
LCD screen displays the low-cut symbol.
3.Manual pairing: long press the "low cut/pairing" button to enter
pairing mode. When rebooting TX and entering pairing mode, the
signal display symbol will be dynamically displayed until it is
paired with the receiver (RX).
4. Charging function: the TX can be charged by connecting the
cable through the storage case or directly through the USB-C
charging cable, with charging dynamics displayed on the LCD
screen while charging.
Receiver

Receiver Screen
① Stereo: Stereo sound channel / Mono: Mono sound channel
① Knob 1:volume up or down for receiver A (press knob 1 and
knob 2 simultaneously to pair)
② Display: LCD display
③ Knob 2: volume up or down for receiver B (press knob 1 and
knob 2 simultaneously to pair)
④ Power button: receiver on / off
⑤ 3.5mm port 2: TRS / TRRS headphone monitor jack
⑥ 3.5mm port 1: TRS audio output port
⑦ USB-C port: 5V charging port

Operations
1.Switch button: long press to power on/ off. "SmallRig" logo
appears on the LCD screen after power on. In power on mode, for
each short press, the audio output switches between
mono/stereo, and the display will show "Mono" / "Stereo".
2. Gain adjustment: through the group A volume adjustment
knob, rotate it clockwise to increase the volume, and vice versa to
reduce the volume. Through group B volume adjustment knob,
rotate it clockwise to increase the volume, and vice versa to
reduce the volume. The gain is displayed in three colors, in which
green means below -12dB, yellow means -12dB ~ 0dB, and red
means above 0dB.
3. Manual pairing: the volume adjustment button on the RX is
used as a pairing button when pressing. When the volume
buttons of groups A and B are pressed simultaneously, the
receiver enters the pairing mode (for TX, long press the pairing
button). At the same time, the group information is flashing on
the display, until it is paired with the transmitter (TX) . After
connecting to the transmitter, the group information is of reverse
display, otherwise hollow display, in black font In pairing mode,
press any button to exit.
4. Charging function: the RX can be charged by connecting the
cable through the storage case or directly through the USB-C
charging cable, with charging dynamics displayed on the LCD
screen while charging.
② Receiver battery capacity
③ Microphone audio bar of channel A / Microphone audio
bar of channel B
④ Channel A output volume / Channel B output volume

Storage Case
1. Charging: red display when connected to the power supply to
charge RX/TX, and green display when RX / TX is fully charged.
2. Port: with USB-C charging port, and built-in USB-A charging cable
at the bottom of the storage case.
Operating Instructions
Transminer
Mount the transmitter to the collar via the back clip so that
the built-in microphone points in the direction of the audio
source.
(Note: In the process of use, for better concealment, it is
recommended that the back clip is fixed towards the
outside for use)
Use an external microphone
Plug the 3.5mm TRS microphone input cable into the
transmitters 3.5mm TRS external microphone jack. Clip the
transmitter to your belt via the back clip, then clip the lavalier
microphone on the other end to your collar.
(Note: When using an external microphone, the built-in
microphone will automatically turn off)
Receiver
Method for using with the camera
Clip the receiver to the camera's cold shoe mount via the
back clip. Connect the receiver to the camera via 3.5mm
TRS-TRS cable. Plug the headphones into the headphone
monitor hole for monitoring.

Method for using with the mobile phone
Clip the receiver to the cold shoe mount via the back clip.
Connect the receiver to the mobile phone via 3.5mm TRS-TRRS
cable, and note that the access to the receiver audio output jack
is 3.5mm TRS plug, access to the mobile phone end is 3.5mm
TRRS plug. Plug the headphones into the headphone monitor
jack for monitoring.

Frequency Response
⸺0 Deg
Directionality
Microphone Frequency Response dB Ref. 1V/Pa

Specifications and Parameters
Transmitter
Wireless band 2402 ~2480MHz
Microphone directionality Omni-directional
Sound delay <15ms
External input port 3.5mm TRS microphone input
Battery specification 450mAh 3.7V 1.665Wh
Endurance time 8h
Display LCD display
Operating distance 100m (without obstacles)
Charging time 1h
Input voltage 5V

Receiver
Wireless band 2402 ~2480MHz
RF sensitivity -81dB
Sound delay <15ms
Output port 1 3.5mm TRS audio output
Output port 2 3.5mm TRS /TRRS headphone output
Battery specification 630mAh 3.7V 2.331Wh
Endurance time 8h
Display LCD display
Input voltage 5V
Number of audio channels 2 channels
Charging time 1.5h
Operating distance 100m (without obstacles)

Guarantee Card
Serial No.
Item Name
Purchase Date
User Name
Mobile
Address
Receipt
FCC Caution
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
This device and its antenna(s) must not be co-located or operating in conjunction with
any other antenna or transmitter.
NOTE
This equipment has been tested and found to comply with the limits fora Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction.
FCC ID: 2AZWI-3487LEQI
ISED Statement
English: This device contains licence-exempt transmitter(s)/receiver(s) that
comply with Innovation, Science and Economic Development Canada's
licence-exempt RSS(s).Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may
cause undesired operation of the device.
The digital apparatus complies with Canadian CAN ICES-3 (B)/NMB-3(B).
French: Cet appareil contient des émetteurs/récepteurs exempts de licence qui
sont conformes aux RSS exemptés de licence d'lnnovation, Sciences et
Développement économique Canada.
L'exploitation est soumise aux deux conditions suivantes:
(1) Cet appareil ne doit pas provoquer d'interférences.
(2) Cet appareil doit accepter toute interférence, y compris les interférences
susceptibles de provoquer un fonctionnement indésirable de l'appareil.
L'appareil numérique du ciem conforme canadien peut -3(b) / nmb-3 (b).
This device meets the exemption from the routine evaluation limits in section 2.5
of RSS 102 and compliance with RSS 102 RF exposure, users can obtain Canadian
information on RF exposure and compliance.
Cet appareil est conforme à l'exemption des limites d'évaluation courante dans
la section 2.5 du cnr- 102 et conformité avec rss 102 de l'exposition aux rf, les
utilisateurs peuvent obtenir des données canadiennes sur l'exposition aux
champs rf et la conformité.
This equipment complies with Canada radiation exposure limits set forth for an
uncontrolled environment.

Cet équipement est conforme aux limites d'exposition aux rayonnements du
Canada établies pour un environnement non contrôlé.
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction.
L'appareil a été évalué pour répondre aux exigences générales d'exposition aux
radiofréquences. L'appareil peut être utilisé en condition d'exposition portable
sans restriction.
IC: 27649-3487LEQI
Service Warranty
Please keep your original receipt and guarantee card. Be sure the dealer has
written on it the date of purchase and SN of the product. These are required for
warranty service.
After-sale warranty terms
This warranty does not cover
1. Defect caused by users' violation of the "Warnings" and "Intended Use".
2. The product identification or SN label is removed or defaced in any way.
3. The product is serviced or repaired by any one other than our company or the
service agency authorized by our company.
2. 1-Year Warranty: Within 1-year from the date of the package receipt,defective
product which is not caused by human abused is eligible to get repair /
replacement for free; defective product which is caused by humanabused,
repair/ replacement will be charged based on the damage level.
1. 7 Days DOA Return Policy: Within 7 days from the date of the packagereceipt,
return or replacement can be done if the item received ismalfunctioning or
physical damaged (not caused by human abused), returnshipping cost will be
on SmallRig's charge.

Vorwort
Vielen Dank, dass Sie ein SmallRigs Produkt gekauft haben.
Wichtige Hinweise
Bitte lesen Sie dieses Benutzerhandbuch sorgfältig durch.
Verwenden Sie das Produkt nicht im Wasser, da es weder staub-
noch wasserdicht ist.
Achten Sie darauf, dass das Gerät nicht auf den Boden fällt,
geschlagen wird oder heftigen Stößen ausgesetzt ist.
Üben Sie keinen Druck auf den LCD-Bildschirm aus, da zu starker
Druck den Bildschirm dauerhaft beschädigen kann.
Verwenden Sie das Produkt nicht in einem vollständig
geschlossenen Raum, da es sonst zu einem Anstieg der
Innentemperatur kommen kann, was zu einem Produktausfall,
einer Selbstentzündung oder einem anderen Unfall führen kann.
Setzen Sie das Gerät nicht übermäßiger Hitze aus, da hohe
Temperaturen zu Fehlfunktionen führen können.
Stellen Sie das Gerät nicht an einem Ort mit ätzenden
Chemikalien auf, um es vor Korrosion zu schützen, da dies zu
Fehlfunktionen führen kann.
Stellen Sie das Gerät nicht in der Nähe von brennbaren oder
flüchtigen Lösungen auf, da es sonst zu einer Brandkatastrophe
oder Smogbildung kommen kann.
Schalten Sie das Gerät unbedingt aus, wenn Sie es nicht
benutzen.
Verwenden Sie zur Reinigung des Produkts nur ein trockenes
Mikrofasertuch.
17

Nehmen Sie die fest eingebaute Lithiumbatterie niemals
eigenmächtig heraus.
Wenn der Akku längere Zeit nicht benutzt wird, laden und entladen
Sie ihn bitte alle 6 Monate und laden Sie ihn zu etwa 60% auf, um
seine Lebensdauer zu verlängern.
Da die Batterie einige gefährliche Stoffe enthält, werfen Sie sie bitte
nicht einfach weg. Entsorgen Sie stattdessen das Produkt, das
beschädigt ist oder nicht mehr verwendet wird, gemäß den
Maßnahmen der Abfallwirtschaft.
Hinweis: Um die Lebensdauer des Geräts zu verlängern, sollten Sie
es während des Ladevorgangs so wenig wie möglich benutzen.
Warnung
Bitte zerlegen Sie das Produkt nicht. Wenn Sie ein Problem mit
dem Produkt vermuten, wenden Sie sich bitte an die
Verkaufsplattform und beantragen Sie eine Kundendienstleistung
Standardverwendung des Geräts
Der Standardgebrauch des SmallRig Forevala W60
Drahtlosmikrofons umfasst
Lesen Sie dieses Handbuch sorgfältig durch, insbesondere den
Abschnitt "Wichtige Hinweise".
Verwenden und lagern Sie das Produkt unter den in diesem
Handbuch angegebenen Arbeitsbedingungen.
18

In der Box
Sender (TX)
Empfänger (RX)
Aufbewahrungsbox
TRS zu TRS Kabel
TRS zu TRRS Kabel
Winddichte Abdeckung
USB-C Ladekabel
SmallRig Metall-Aufkleber
Tragetasche
Benutzerhandbuch
Produktdetails
Sender
19