Smartech JS-15000N User manual

User Guide
Guía del usuario
Jump Starter / Power Bank
Model/Modelo: JS-15000N
CRANKING CURRENT: 400 Amps
PEAK CURRENT: 800 Amps
OUTPUT: 2x5V/2.4A, 12V/10A, 19V/3.5A
BATTERY CAPACITY: 15000mAh/55.5Wh
FULLY CHARGE IMMEDIATELY AFTER PURCHASE.
Fully recharge after each jumpstarting, or every 3 months to ensure
long battery life.
Jump • Charge • Power

USER GUIDE PAGE 2JS-15000N
DANGER
Please read and understand all important
safety and operating instructions before
using this charger. In addition, please
read and follow all battery and vehicle
manufacturer’s instructions and
cautionary markings. Failure to follow the
instructions may result in ELECTRICAL
SHOCK, EXPLOSION, or FIRE, which
may result in SERIOUS INJURY, DEATH,
DAMAGE TO DEVICE or PROPERTY. Do
not discard this information.
Operating Manual has been designed to instruct you on the correct use and
operation of your product. Your satisfaction with this product and its safe
operation is our ultimate concern. Therefore please take the time to read the
entire manual, especially the Safety Precautions. They will help you to avoid
potential hazards that may exist when working with this product.
Published by:
Smartech Products, Inc.
8700 Larkin Rd.
Savage, MD 20763
[phone]
www.smartechproduct.com
Copyright © 2018 by Smartech Products, Inc.
Reproductions of this work, in whole or in part, without written permission of
the publisher are strictly prohibited.
The publisher does not assume and herby disclaims any liability to any party
for any loss or damage caused by any error or omission in this manual,
whether such error results from negligence, accident, or any other cause.

USER GUIDE PAGE 3JS-15000N
SAFETY INFORMATION
Please read this entire manual before using this product.
1. Avoid dangerous environments. Do not charge this item in rain,
snow, damp or wet environments.
2. Do not use this item or charger in the presence of explosive
atmospheres (gaseous fumes, dust or ammable materials) since
sparks may be generated when attaching or removing this item,
possibly causing re.
3. Charge in a well-ventilated area. Do not allow smoking or open ames
near a charging battery. Vented gases may explode.
4. Do not burn or incinerate this item. This item may explode, causing
personal injury or damage. Toxic fumes and materials are created
when batteries are burned.
5. Do not crush, drop or damage this item.
6. Do not use this item or a battery charger that has received a sharp
blow, been dropped, run over or damaged in any way (e.g. pierced with
a nail, hit with a hammer or stepped on).
7. WARNING: Do not disassemble. Disassembly may result in the risk of
electric shock, re or exposure to battery chemicals.
8. Battery chemicals cause serious burns. Never allow contact with skin,
eyes or mouth. If this item leaks battery chemicals, use rubber or
neoprene gloves to dispose of it. If skin is exposed to battery uids,
wash with soap and water and rinse with vinegar. If eyes are exposed
to battery chemicals, immediately ush with water for 20 minutes and
seek medical attention. Remove and dispose of contaminated clothing.
9. Do not short circuit. This item will short circuit if a metal object makes
connection to the power cable port. Do not place this item near
anything that may cause a short circuit, such as coins, keys or nails. A
shortcircuited battery may cause re and personal injury.
10. When jump starting your vehicle do not place Jump Starter on the
ground or at a height less than 18 inches.
11. Never charge or jump start a frozen battery. Store this item and
charger in a cool dry place.

USER GUIDE PAGE 4JS-15000N
12. Do not store this unit for more than 10 days where temperatures may
exceed 120 Degrees F (50 Degrees C) such as direct sunlight, a
vehicle, or metal building during the summer as it may cause damage
to the unit.
13. This product is intended for private use only and should not be used
in any commercial applications. Use of this product to start multiple
vehicles over a short period of time may damage the jump starter/
charger.
14. WARNING: Before attempting to start a vehicle, be sure the blue plug
of the Smart Jumper Cables is rmly secured into the Smart Jumper
Cable Input Socket and be sure that the battery clamps have a good
connection with the proper battery terminals. Clean rusted or dirty
terminals before attempting to jumpstart the vehicle.
15. WARNING: Remove the jump starter from the vehicle battery within 30
seconds of successfully restarting. To do so, remove the Smart Jumper
Cables from the Jump Starter. Then remove the Smart Jumper Cables
from the battery terminals.
16. WARNING: Only use the provided charging cords with this product
17. WARNING: Disposal of this Device. This device contains a non-
replaceable Lithium Polymer battery. It is not user replaceable. Battery
must be disposed of properly when it no longer holds a charge. This
product should be recycled or disposed of as per state and local
guidelines.
18. WARNING: This product is not a toy and is not intended for use by
children.
19. PROPOSITION 65 WARNING: This Product contains chemicals
known to the State of California to cause cancer and birth defects
or other reproductive harm (California law requires this warning to
be given to customers in the State of California). Wash hands after
handling.

USER GUIDE PAGE 5JS-15000N
LAPTOP CHARGER TIPS
CONSEJOS PARA EL CARGADOR PORTÁTIL
SMART BATTERY CLAMPS
PINZAS SMART BATTERY
INCLUDED ACCESSORIES
ACCESORIOS INCLUIDOS
2 IN 1 USB CABLE
CABLE USB 2 EN 1
CARRYING CASE
ESTUCHE DE TRANSPORTE
CAR CHARGER
CARGADOR DE COCHE
CARGADOR DE PARED
WALL CHARGER
12V ADAPTER
ADAPTADOR 12V
FEATURES - ABOUT THIS PRODUCT
Features Built-In Protection: Spark Proof Protection, Reverse Polarity
Protection, Short Circut Protection, Over Current Protection, Over Discharge
Protection, Over Charge Protection, Self Discharging Protection and Over
Heat Protection. This product can instantly jump start most single battery
vehicles, up to 70+ (over 70) times on a full charge. This product is also
equipped with USB power output, LED ashlight, 12VDC power output and
a 19V output for laptops.
RISK OF EXPLOSIVE GASES
WORKING IN THE VICINITY OF A LEAD-ACID BATTERY
IS DANGEROUS. BATTERIES GENERATE EXPLOSIVE GASES
DURING NORMAL BATTERY OPERATION. FOR THIS REASON,
IT IS OF UTMOST IMPORTANCE THAT YOU FOLLOW THE
INSTRUCTIONS EACH TIME YOU USE THE CHARGER.
To reduce risk of battery explosion, follow these instructions and those published by
battery manufacturer and manufacturer of any equipment intended to be used in vicinity
of battery. Review cautionary marking on these products and on engine.

USER GUIDE PAGE 6JS-15000N
About the JS-15000N:
About the Smart Jumper Clamps:
STATUS LED
EC5 Plug
Positive Clamp
Negative Clamp
%
5VUSB 2.4A
15V 5V
IN
OUT 19V 3.5A
1) Flashlight
2) Battery Capacity
3) 5V/2.4A Output
4 & 7) 5V/2A Input
5 & 7) 15V/1A Input
6) 19V/3.5A Output
Power Button
Built-In 8000mAh
Lithium Ion Battery
3 Mode
LED Flashlight
Battery Status /
Output Display
EC5 Engine Start Socket
15V/1A INPUT PORT
5V/2A INPUT PORT
19V/3.5A OUTPUT PORT (2) 5V/2.4A USB Outputs
12
3
4
5
6
7

USER GUIDE PAGE 7JS-15000N
TECHNICAL SPECIFICATION:
Battery Type Lithium-ion Polymer
Battery Capacity 15000mAh
Starting Current 400A
Peak Current 800A
Jump Start Up to 6.0L Gas Engine, 5.0L Diesel
Engine
USB Output 5V/2.4A, 5V/2.4A
LED Flashlight 2W
12V Output 10A Max
19V Output 19V/3.5A for Laptops
Operating Temperature -22°F - +122°F
Charging Temperature 32°F - +104°F
Storage Temperature -4°F - +95°F (For 3 months)

USER GUIDE PAGE 8JS-15000N
LED AND BUZZER COMMUNICATION:
Red LED Green
LED
Buzzer
Sound Condition
1 On Off One sound
Jumper cables and jump
starter are connected.
Ready for connection to
vehicle battery.
2Off On One sound
Jumper cable and
vehicle battery are
connected. Ready to
start the engine.
3Slow ash Off No buzzer Lithium battery voltage in
jump starter is low.
4Slow ash Off No buzzer
Have not turned on the
ignition switch within
the regulated time. To
resolve this, you need
remove clamps from
vehicle battery, and
connect again when
No.1 condition occurs.
5Fast ash Off Fast buzzer
Red and black clamps
are connected with each
other.
6Fast ash Off Fast buzzer Reverse connection of
clamps.
7Off Fast ash No buzzer Engine is started.
8Off Fast ash No buzzer
Vehicle’s battery voltage
is higher than Jump
Starter’s.

USER GUIDE PAGE 9JS-15000N
CONNECTING TO THE BATTERY
1. Identify polarity of battery posts. The positive battery terminal is
typically marked by these letters or symbol (POS,P,+). The negative
battery terminal is typically marked by these letters or symbol
(NEG,N,-).
2. Do not make any connections to the carburetor, fuel lines, or any thin
metal parts.
3. Identify if you have a negative or positive grounded vehicle. This can
be done by identifying which battery post (NEG or POS) is connected
to the chassis.
4. For a negative grounded vehicle (most common): connect the RED
POSITIVE jumper clamp rst to the positive battery terminal, then
connect the BLACK NEGATIVE jumper clamp to the negative battery
terminal or vehicle chassis
5. For a positive grounded vehicle (very uncommon): connect the BLACK
NEGATIVE jumper clamp rst to the negative battery terminal, then
connect the RED POSITIVE jumper clamp to the positive battery
terminal or vehicle chassis
6. When disconnecting, disconnect in the reverse sequence, removing
the negative rst (or positive rst for positive ground systems).
JUMP STARTING
1. This unit is only for emergency use, not for frequent commercial
use! ENGINE START socket is ALWAYS activated! Do not attempt to
jumpstart your vehicle when the jump starter battery capacity is below
30% (observe battery status indicator on the unit).
2. Turn off the vehicle ignition and all accessories (radios, lights, air
conditioners, etc.), and disconnect electronic devices.
3. Connect the jumper clamps to the correct polarity battery terminals as per
item 3 in the previous CONNECTING TO THE BATTERY section.
4. Connect the EC5 plug of jumper cables to the ENGINE START socket
of jump starter. If the Green LED doesn’t turn on use BOOST. Refer to the
“BOOST” OPERATION section.
5. Try starting the vehicle (turn on the ignition switch). Most vehicles will

USER GUIDE PAGE 10JS-15000N
immediately start. Stop if the vehicle does not start after 5 seconds
of engine cranking. The jumpstart feature is designed for short term
operation only, and more than 5 seconds may cause damage to the
unit. Allow the jump starter to cool down for at least 3 minutes after
each jumpstarting.
6. Disconnect the cable from the jump starter immediately after engine
starts, and then remove from battery terminals.
“BOOST” OPERATION:
1. Connect the Jump Starter to the vehicle battery (Red LED keeps on and
green LED is off), press and hold BOOST button for 3 seconds (after a
buzzer sound, the green LED is on and red LED is off). “BOOST” is used
when the vehicle battery capacity is low.
2. Start the engine (same method as the normal operations in Page 7).
Cautions:
1. Under normal circumstances, do not use BOOST. Use only when the
vehicle battery capacity is low.
2. The spark proof, reverse polarity protection and short circuit protection
features are disabled after Boost button is pressed. Pay very close
attention to the polarity of the battery before using this mode. Do not
allow the positive and negative battery clamps to touch or connect to
each other as the item will generate sparks and high heat if not used
properly.
CHARGING
This product is partially charged from the manufacturer. Fully charge the unit
immediately after purchase. In order to prolong the product life, be sure to
fully recharge the unit after each jumpstaring, or every 3 months even if this
unit has not been used. If battery voltage in the jump starter is too low, this
item will shut off to prevent damage to itself. Recharge the unit as soon as
possible to be activated and fully charge it to ensure long battery life. In addi-
tion, we recommend not to charge and discharge the unit at the same time.

USER GUIDE PAGE 11JS-15000N
AC CHARGING:
1. Insert AC charging adapter into charging jack of the unit.
2. Plug the other end of AC charging adapter into a wall socket.
3. Fully charge the unit.
4. When charging is complete, unplug the AC charging adapter from the
wall socket rst, then from the charging jack on the jump starter.
DC CHARGING IN YOUR VEHICLE:
1. Turn the vehicle engine on.
2. Insert the DC charging adapter into the charging jack of the unit.
3. Plug the other end of DC charging adapter into vehicle’s cigarette
lighter socket.
4. Fully charge the unit. Engine must keep running during entire charge.
5. When charging is completed, unplug the DC charging adapter from the
vehicle rst, then from the charging jack on the jump starter.
USB CHARGING:
This product has a USB cable that can also be used to recharge the
jump starter.
Charging Time:
LCD will show “100%” as fully charged. Charging time will differ based
on the discharge level and the power source used. If charging begins
from 5% to full charge, it approximately takes approxiamately 7 hours
for AC charging
USB POWER
Connect the USB device to the jump starter with either the original cable
or the included multi-tip cable (it’s better to use Apple® cables for Apple®
products). Press Power button to start USB power. When disconnected,
the jump starter will automatically shut off. The number of times you can
recharge a USB device will vary between devices.
FLASHLIGHT
Press and hold Power button for 3 seconds to start ashlight. Press once to
switch lighting modes: Steady On – Strobe – SOS – Off.

USER GUIDE PAGE 12JS-15000N
SMARTECH INC. LIMITED WARRANTY
Repair/Replacement Warranty
Smartech Inc. warrants to the original purchaser that the mechanical and
electrical components will be free of defects in material and workmanship
for a period of one (1) year from the original date of purchase. This product
is intended for household use only. Transportation charges on product
submitted for repair or replacement under this warranty are the sole
responsibility of the purchaser. This workmanship for a period of warranty
only applies to the original purchaser and is not transferable. Do not return
the unit to the place of purchase. Contact Smartech Inc. Customer Service
and Smartech Inc. will troubleshoot any issue via phone or e-mail. If the
problem is not corrected by this method, Smartech Inc. will, at its option,
authorize evaluation, repair or replacement of the defective part or
SUPPLY TO 19V DEVICES
Select the appropriate input tip and connect the jump starter with your lap-
top. Press the Power button to start 19V/3.5A power. When disconnected,
the jump starter will automatically shut off. The number of times you can
rechaerge a laptop will vary between decives.
SUPPLY TO 12V DEVICES
The jump starter can run/charge 12VDC appliances that draw 10 amps or
less.
OPTION 1:
Connect the jump starter to 12V devices with the optional accessory
(accessory not included). Press Power button to start 12V power.
When disconnected, the jump starter will automatically shut off.
OPTION 2:
. Connect the jump starter to 12V devices by the incuded accessory. You
do not need to press the Power button as the EC5 12VDC output is
ALWAYS activated. When the battery voltage of the jump starter is too

USER GUIDE PAGE 13JS-15000N
SMARTECH INC. LIMITED WARRANTY (continued)
component at a Smartech Inc. Service Center. Repairs or replacements
without prior authorization, or at an unauthorized repair facility, will not be
covered.
Warranty Exclusions
This warranty does not cover the following repairs and equipment:
Normal Wear
This warranty does not cover repair when normal use has exhausted the life
of a part or the equipment as a whole.
Installation and Use
This warranty will not apply to parts and/or labor if this product is deemed to
have been misused, neglected, involved in an accident, abused, modied,
installed improperly or connected incorrectly to any electrical component.
Other Exclusions
This warranty excludes:
• Merchandise sold as reconditioned, used as rental equipment or
oor/display models sold without packaging and/or missing parts or
components.
• Repair and transportation costs of merchandise determined not to be
defective.
• Cosmetic defects such as paint, decals, etc.
• Failures due to acts of God and other forces of nature beyond the
manufacturer’s control.
• Problems caused by parts that are not original parts.

USER GUIDE PAGE 14JS-15000N
SMARTECH INC. LIMITED WARRANTY (continued)
Limits of Implied Warranty and Consequential Damage
Smartech Inc. disclaims any obligation to cover any loss of time, use of this
product, freight, or any incidental or consequential claim by anyonefrom
using this product. THIS WARRANTY IS IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
A unit provided as an exchange will be subject to the warranty of the original
unit. The length of the warranty governing the exchanged unit will remain
calculated by reference to the purchase date of the original unit. This
warranty gives you certain legal rights which may change from state to
state. Your state may also have other rights you may be entitled to that are
not listed within this warranty. Some states do not allow the exclusion, so it
may not apply to you.
Contact us at:
Smartech Inc.
8700 Larkin Rd., Suite B
Savage, MD 20763
[phone]
© 2019 Smartech, Inc.

USER GUIDE PAGE 15JS-15000N