Smartech UltraTec-8000 User manual

User Guide
Guía del usuario
Rechargeable LED Flashlight / Portable Power
Bank / Jump Starter
Model/Modelo: UltraTec-8000
LUMEN OUTPUT: 8000
PEAK STARTING CURRENT: 500 Amps
USB OUTPUT: (2)x5V/2.4A
BATTERY CAPACITY: 10000mAh
FULLY CHARGE IMMEDIATELY AFTER PURCHASE.
Fully recharge after each jumpstarting, or every 3 months to ensure
long battery life.
ILLUMINATE • POWER • CHARGE • JUMP

USER GUIDE PAGE 2ULTRATEC-8000
DANGER
Please read and understand all important
safety and operating instructions before
using this charger. In addition, please
read and follow all battery and vehicle
manufacturer’s instructions and
cautionary markings. Failure to follow the
instructions may result in ELECTRICAL
SHOCK, EXPLOSION, or FIRE, which
may result in SERIOUS INJURY, DEATH,
DAMAGE TO DEVICE or PROPERTY. Do
not discard this information.
This operating manual has been designed to instruct you on the correct
use and operation of your product. Your satisfaction with this product and
its safe operation is our ultimate concern. Therefore please take the time to
read the entire manual, especially the Safety Precautions. They will help you
to avoid potential hazards that may exist when working with this product.
RISK OF EXPLOSIVE GASES
WORKING IN THE VICINITY OF A LEAD-ACID BATTERY
IS DANGEROUS. BATTERIES GENERATE EXPLOSIVE GASES
DURING NORMAL BATTERY OPERATION. FOR THIS REASON,
IT IS OF UTMOST IMPORTANCE THAT YOU FOLLOW THE
INSTRUCTIONS EACH TIME YOU USE THE CHARGER.
To reduce risk of battery explosion, follow these instructions and those
published by battery manufacturer and manufacturer of any equipment
intended to be used in vicinity of battery. Review cautionary marking on these
products and on engine.

USER GUIDE PAGE 3ULTRATEC-8000
SAFETY INFORMATION
Please read this entire manual before using this product.
1. Avoid dangerous environments. Do not charge this item in rain,
snow, damp or wet environments.
2. Do not use this item or charger in the presence of explosive
atmospheres (gaseous fumes, dust or ammable materials) since
sparks may be generated when attaching or removing this item,
possibly causing re.
3. Charge in a well-ventilated area. Do not allow smoking or open ames
near a charging battery. Vented gases may explode.
4. Do not burn or incinerate this item. This item may explode, causing
personal injury or damage. Toxic fumes and materials are created
when batteries are burned.
5. Do not crush, drop or damage this item.
6. Do not use this item or a battery charger that has received a sharp
blow, been dropped, run over or damaged in any way (e.g. pierced with
a nail, hit with a hammer or stepped on).
7. WARNING: Do not disassemble. Disassembly may result in the risk of
electric shock, re or exposure to battery chemicals.
8. Battery chemicals cause serious burns. Never allow contact with skin,
eyes or mouth. If this item leaks battery chemicals, use rubber or
neoprene gloves to dispose of it. If skin is exposed to battery uids,
wash with soap and water and rinse with vinegar. If eyes are exposed
to battery chemicals, immediately ush with water for 20 minutes and
seek medical attention. Remove and dispose of contaminated clothing.
9. Do not short circuit. This item will short circuit if a metal object makes
connection to the power cable port. Do not place this item near
anything that may cause a short circuit, such as coins, keys or nails. A
shortcircuited battery may cause re and personal injury.
10. When jump starting your vehicle do not place Jump Starter on the
ground or at a height less than 18 inches.
11. Never charge or jump start a frozen battery. Store this item and
charger in a cool dry place.

USER GUIDE PAGE 4ULTRATEC-8000
SAFETY INFORMATION (continued)
12. Do not store this unit for more than 10 days where temperatures may
exceed 120 Degrees F (50 Degrees C) such as direct sunlight, a
vehicle, or metal building during the summer as it may cause damage
to the unit.
13. This product is intended for private use only and should not be used
in any commercial applications. Use of this product to start multiple
vehicles over a short period of time may damage the jump starter/
charger.
14. WARNING: Before attempting to start a vehicle, be sure the blue plug
of the Smart Jumper Cables is rmly secured into the Smart Jumper
Cable Input Socket and be sure that the battery clamps have a good
connection with the proper battery terminals. Clean rusted or dirty
terminals before attempting to jumpstart the vehicle.
15. WARNING: Remove the jump starter from the vehicle battery within 30
seconds of successfully restarting. To do so, remove the Smart Jumper
Cables from the Jump Starter. Then remove the Smart Jumper Cables
from the battery terminals.
16. WARNING: Only use the provided charging cords with this product
17. WARNING: Disposal of this Device. This device contains a non-
replaceable Lithium Polymer battery. It is not user replaceable. Battery
must be disposed of properly when it no longer holds a charge. This
product should be recycled or disposed of as per state and local
guidelines.
18. WARNING: This product is not a toy and is not intended for use by
children.
19. PROPOSITION 65 WARNING: This Product contains chemicals
known to the State of California to cause cancer and birth defects
or other reproductive harm (California law requires this warning to
be given to customers in the State of California). Wash hands after
handling.

USER GUIDE PAGE 5ULTRATEC-8000
Features 8000 lumen recharable LED ashlight with 10000mAh
power bank with Built-In jump starter function. The jump starter
features: Spark Proof Protection, Reverse Polarity Protection, Short
Circut Protection, Over Current Protection, Over Discharge Protec-
tion, Over Charge Protection, Self Discharging Protection and Over
Heat Protection. This product can instantly jump start most single
battery vehicles, up to 24+ (over 24) times on a full charge. This
product is also equipped with 2 USB power output ports to power/
charge USB devices.
ABOUT THE ULTRATEC-8000

USER GUIDE PAGE 6ULTRATEC-8000

USER GUIDE PAGE 7ULTRATEC-8000
Battery Type Lithium-ion Polymer
Battery Capacity 10000mAh Rechargeable
Starting Current 200A
Peak Current 500A
Jump Start Gas Engine Up to 4.0L
Jump Start Diesel Engine Up to 3.0L
USB Output (2) 5V/2.4A, 5V/2.4A
LED Flashlight 8000 Lumens Max. Brightness
Light Modes 6 - Turbo/High/Medium/Low/Strobe/
SOS
Turbo Brightness 8000 Lumens
High Brightness 3000 Lumens
Medium Brightness 1500 Lumens
Low Brightness 150 Lumens
Operating Temperature -22°F - +122°F
Charging Temperature 32°F - +104°F
Storage Temperature -22°F - +122°F (For 3 months)
TECHNICAL SPECIFICATIONS
Flashlight Specications:
Brightness
in Lumens
Beam
Distance
Hours of
Operation

USER GUIDE PAGE 8ULTRATEC-8000
CHARGING THE ULTRATEC-8000
Option 1: Home Charging
To charge the UltraTec-8000, plug the USB C to USB charging
cable into the back of the UltraTec-8000 ashlight. Plug the other
end of the cable into the wall charger adaptor. Plug the wall charger
adaptor into a wall outlet. There are 4 blue LED charging indicators
that will show the charging status of the UltraTec-8000.
See image below:

USER GUIDE PAGE 9ULTRATEC-8000
Option 2: Car Charging
To charge the UltraTec-8000 from your car, plug the USB C to
USB charging cable into the back of the UltraTec-8000 ashlight.
Plug the other end of the cable into the 12V to USB adaptor.
Plug the USB adaptor into the car cigarette lighter socket power
outlet. There are 4 blue LED charging indicators that will show the
charging status of the UltraTec-8000.
See image below:
USB C TO USB
CHARGING CABLE
USB C
CHARGING
PORT
12V TO USB
ADAPTOR

USER GUIDE PAGE 10ULTRATEC-8000
The UltraTec-8000 has 6 light modes.
1. Turbo (highest brightness)
2. High
3. Medium
4. Low
5. Strobe
6. S.O.S
To turn on the ashlight, press the round power button. Press the
power button repeatedly to cycle through the High/Medium/Low/
Strobe/S.O.S. modes.
Quick Access:
Double click to Strobe mode. One more click to S.O.S mode.
To turn on “Turbo” mode: From any mode (including OFF), press
and hold the power button for 1 second.
See image below:
Quick Access:
Double click to Strobe mode, one more click to S.O.S mode
POWER BUTTON
6 LIGHT MODES
TURBO MODE:
Press repeatedly to cycle through
the following modes:
• High
• Medium
• Low
• Strobe
• S.O.S.
Press and hold for 1 second to turn flashlight
on in Turbo mode:
USING THE LED FLASHLIGHT

USER GUIDE PAGE 11ULTRATEC-8000
The UltraTec-8000 comes with three colored lenses: green, red and
blue, that you can easily attach to the front of the UltraTec-8000.
USING THE COLORED LED FLASHLIGHT LENSES
To remove the lens, simply
unscrew it.
See Figure B.
To attach the lens, gently screw
it onto the front of the ashlight.
See Figure A.
Leave the lense off for
a clear white light, or
replace it with another
color.
Turn on the ashlight!
Figure A. Figure B.

USER GUIDE PAGE 12ULTRATEC-8000
STATUS LED
EC5 Plug
Positive Clamp
Negative Clamp
ABOUT THE SMART JUMPER CABLES

USER GUIDE PAGE 13ULTRATEC-8000
JUMP START YOUR VEHICLE USING THE
ULTRATEC-8000
1. Identify the polarity of the battery posts. The positive battery
terminal is typically marked by these letters or symbols
(POS,P,+). The negative battery terminal is typically marked by
these letters or symbols (NEG,N,-).
2. Do not make any connections to the carburetor, fuel lines, or
thin metal parts.
3. Identify if you have a negative or positive grounded vehicle.
4. This can be done by identifying which battery post (NEG or
POS) is connected to the chassis.
5. For a negative grounded vehicle (most common): connect
the RED POSITIVE jumper clamp rst to the positive battery
terminal, then connect the BLACK NEGATIVE jumper clamp to
the negative battery terminal or vehicle chassis.
6. For a positive grounded vehicle (very uncommon): connect the
BLACK NEGATIVE jumper clamp rst to the negative battery
terminal, then connect the RED POSITIVE jumper clamp to the
positive battery terminal or vehicle chassis.
7. When disconnecting, disconnect in the reverse sequence,
removing the negative rst (or positive rst for positive ground
systems).
JUMP STARTING PROCEDURE
1. This unit is only for emergency use, not for frequent commercial
use! ENGINE START socket is ALWAYS activated! Do not attempt
to jumpstart your vehicle when the UltraTec-8000 Power Bank
battery capacity is below 30%.
2. Turn off the vehicle ignition and all accessories (radios, lights, air
conditioners, etc.), and disconnect electronic devices.
ATTACHING THE BATTERY CLAMPS

USER GUIDE PAGE 14ULTRATEC-8000
3. Connect the jumper clamps to the correct polarity battery terminals.
(See the previous Attaching The Battery Clamps section.)
4. Connect the EC5 plug of jumper cables to the ENGINE START
socket of the UltraTec-8000.
5. Try starting the vehicle (turn on the ignition switch). Most vehicles
will immediately start. Stop if the vehicle does not start after
5 seconds of engine cranking. The jumpstart feature is designed
for short term operation only, and more than 5 seconds may cause
damage to the unit. Allow the UltraTec-8000 to cool down for at
least 3 minutes after each jumpstarting.
6. Disconnect the cable from the ashlight immediately after
engine starts, and then remove from battery terminals.
1 2 3 4 5
(-) VEHICLE CABLE OR
(-) BATTERY TERMINAL
(+) VEHICLE CABLE OR
(+) BATTERY TERMINAL

USER GUIDE PAGE 15ULTRATEC-8000
POWER / CHARGE USB DEVICES
To power or charge your USB devices, connect the USB device to
either of the 2 included USB ports on the UltraTec-8000 ashlight
with the included multi device USB output cable (For Apple® for
Apple® products, it’s better to use the original cable that came with
the device). Press the “Power” button next to the USB ports to turn
on power to the USB ports. The number of times you can recharge
a USB device will vary between devices.
See image below.
(2) USB
OUTPUT PORTS
POWER
BUTTON
MULTI DEVICE
USB OUTPUT CABLE
POWER/CHARGE USB DEVICES
JUMP START PORT
CHARGE
PORT
USB
PORTS
POWER
BUTTON
JUMP STARTPORT
CHARGE
PORT
USB
PORTS
POWER
BUTTON

USER GUIDE PAGE 16ULTRATEC-8000
WARNING: When servicing, use only identical replacement parts.
Use of any other parts can create a hazard or cause product
damage.
WARNING: Always wear eye protection with side shields marked
to comply with ANSI Z87.1. Failure to do so could result in objects
being thrown into your eyes resulting in possible serious injury.
GENERAL MAINTENANCE: Avoid using solvents when cleaning
plastic parts. Most plastics are susceptible to damage from various
types of commercial solvents. Use clean cloths to remove dirt, dust,
oil, grease, etc.
WARNING: Do not at any time let brake uids, gasoline, petroleum-
based products, penetrating oils, etc, come in contact with plastic
parts. Chemicals can damage, weaken or destroy plastic which can
result in serious personal injury.
CALIFORNIA PROPOSITION 65
WARNING: This product and some dust created by power sanding,
sawing, grinding, drilling, and other construction activities may
contain chemicals, including lead, known to the State of California
to cause cancer, birth defects, or other reproductive harm. Wash
hands after handling Some examples of these chemicals are:
• Lead from lead-based paints
• Crystalline silica from bricks and cement and other masonry
products
• Arsenic and chromium from chemically treated lumber.
Your risk from exposure to these chemicals varies, depending on
how often you do this type of work. To reduce your exposure, work

USER GUIDE PAGE 17ULTRATEC-8000
in a well-ventilated area and with approved safety equipment, such
as dust masks that are specially designed to lter out microscopic
particles.
SMARTECH INC. LIMITED WARRANTY
Repair/Replacement Warranty
Smartech Inc. warrants to the original purchaser that the
mechanical and electrical components will be free of defects in
material and workmanship for a period of one (1) year from the
original date of purchase. This product is intended for household
use only. Transportation charges on product submitted for repair or
replacement under this warranty are the sole responsibility of the
purchaser. This workmanship for a period of warranty only applies
to the original purchaser and is not transferable. Do not return the
unit to the place of purchase. Contact Smartech Inc. Customer
Service and Smartech Inc. will troubleshoot any issue via phone
or e-mail. If the problem is not corrected by this method, Smartech
Inc. will, at its option, authorize evaluation, repair or replacement
of the defective part or component at a Smartech Inc. Service
Center. Repairs or replacements without prior authorization, or at
an unauthorized repair facility, will not be covered.
Warranty Exclusions
This warranty does not cover the following repairs and equipment:
Normal Wear
This warranty does not cover repair when normal use has
exhausted the life of a part or the equipment as a whole.

USER GUIDE PAGE 18ULTRATEC-8000
SMARTECH INC. LIMITED WARRANTY (continued)
Installation and Use
This warranty will not apply to parts and/or labor if this product is
deemed to have been misused, neglected, involved in an accident,
abused, modied, installed improperly or connected incorrectly to any
electrical component.
Other Exclusions
This warranty excludes:
• Merchandise sold as reconditioned, used as rental equipment or
oor/display models sold without packaging and/or missing parts
or components.
• Repair and transportation costs of merchandise determined not
to be defective.
• Cosmetic defects such as paint, decals, etc.
• Failures due to acts of God and other forces of nature beyond the
manufacturer’s control.
• Problems caused by parts that are not original parts.
Limits of Implied Warranty and Consequential Damage
Smartech Inc. disclaims any obligation to cover any loss of time,
use of this product, freight, or any incidental or consequential
claim by anyonefrom using this product. THIS WARRANTY IS IN
LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE.

USER GUIDE PAGE 19ULTRATEC-8000
SMARTECH INC. LIMITED WARRANTY (continued)
A unit provided as an exchange will be subject to the
warranty of the original unit. The length of the warranty governing
the exchanged unit will remain calculated by reference to the
purchase date of the original unit. This warranty gives you certain
legal rights which may change from state to state. Your state may
also have other rights you may be entitled to that are not listed
within this warranty. Some states do not allow the exclusion, so it
may not apply to you.
Contact us at:
Smartech Inc.
8700 Larkin Rd.
Savage, MD 20763
[phone]
www.smartechproduct.com
[email protected]
Published by: Smartech Inc.
Copyright © 2019 by Smartech Inc.
Reproductions of this work, in whole or in part, without written permission
of the publisher are strictly prohibited. The publisher does not assume and
herby disclaims any liability to any party for any loss or damage caused
by any error or omission in this manual, whether such error results from
negligence, accident, or any other cause.
© 2019 Smartech, Inc.