SMC Networks EX600-SPR Series User manual

No.EX##-OML0005
Fieldbus system
PROFIBUS DP compatible
PRODUCT NAME
EX600-SPR*
EX600-DX*
EX600-DY*
EX600-AX*
EX600-ED*
MODEL/ Series

- 2 -
No.EX##-OML0005
Table of Contents
Safety Instructions ............................................................................................................................................. 3
Product Outline .................................................................................................................................................. 7
Assembly ........................................................................................................................................................... 9
Mounting and Installation................................................................................................................................. 11
SI Unit .............................................................................................................................................................. 14
How to order................................................................................................................................................. 14
Name and function of the parts.................................................................................................................... 14
Mounting and installation ............................................................................................................................. 15
Setting and adjustment ................................................................................................................................ 16
Error display ................................................................................................................................................. 19
Specifications ............................................................................................................................................... 21
Digital Input Unit .............................................................................................................................................. 23
How to order................................................................................................................................................. 23
Name and function of the parts.................................................................................................................... 23
Mounting and installation ............................................................................................................................. 24
Error display ................................................................................................................................................. 25
Specifications ............................................................................................................................................... 26
Digital Output Unit............................................................................................................................................ 29
How to order................................................................................................................................................. 29
Name and function of the parts.................................................................................................................... 30
Mounting and installation ............................................................................................................................. 30
Error display ................................................................................................................................................. 31
Specifications ............................................................................................................................................... 31
Analog Input Unit ............................................................................................................................................. 33
How to order................................................................................................................................................. 33
Name and function of the parts.................................................................................................................... 33
Mounting and installation ............................................................................................................................. 33
Error display ................................................................................................................................................. 34
Specifications ............................................................................................................................................... 35
End Plate ......................................................................................................................................................... 41
How to order................................................................................................................................................. 41
Name and function of the parts.................................................................................................................... 41
Mounting and installation ............................................................................................................................. 42
Specifications ............................................................................................................................................... 43
Troubleshooting ............................................................................................................................................... 45
Parameter Settings .......................................................................................................................................... 50
Hardware Configuration................................................................................................................................... 58
Accessories ..................................................................................................................................................... 69

- 3 -
No.EX##-OML0005
Safety Instructions
These safety instructions are intended to prevent hazardous situations and/or equipment damage. These
instructions indicate the level of potential hazard by label of "Danger", "Warning" or "Caution", followed by
important safety information which must be carefully followed. To ensure safety of personnel and
equipment the safety instructions in this manual and the product catalogue must be observed, along with
other relevant safety practices.
Caution: If instructions are not followed there is a possibility of injury or equipment
damage.
Warning: If instructions are not followed there is a possibility of serious injury or loss of
life.
Danger: In extreme conditions, there is a possible result of serious injury or loss of life.
Warning
 The compatibility of the product is the responsibility of the person who designs the equipment or
decides its specifications.
Since the product specified here is used under various operating conditions, its compatibility with specific
equipment must be decided by the person who designs the equipment or decides its specifications based
on necessary analysis and test results. The expected performance and safety assurance of the
equipment will be the responsibility of the person who has determined its compatibility with the product.
This person should also continuously review all specifications of the product referring to its latest
catalogue information, with a view to giving due consideration to any possibility of equipment failure when
configuring the equipment.
 Only personnel with appropriate training should operate machinery and equipment.
The product specified here may become unsafe if handled incorrectly. The assembly, operation and
maintenance of machines or equipment including our products must be performed by an operator who is
appropriately trained and experienced.
 Do not service or attempt to remove product and machinery/equipment until safety is confirmed.
 The inspection and maintenance of machinery/equipment should only be performed after measures to
prevent falling or runaway of the driven objects have been confirmed.
 When the product is to be removed, confirm that the safety measures as mentioned above are
implemented and the power from any appropriate source is cut, and read and understand the specific
product precautions of all relevant products carefully.
 Before machinery/equipment is restarted, take measures to prevent unexpected operation and
malfunction.
 Contact SMC beforehand and take special consideration of safety measures if the product is to be
used in any of the following conditions.
 Conditions and environments outside of the given specifications, or use outdoors or in a place exposed
to direct sunlight.
 Installation on equipment in conjunction with atomic energy, railways, air navigation, space, shipping,
vehicles, military, medical treatment, combustion and recreation, or equipment in contact with food and
beverages, emergency stop circuits, clutch and brake circuits in press applications, safety equipment or
other applications unsuitable for the standard specifications described in the product catalogue.
 An application, which could have negative effects on people, property, or animals requiring special safety
analysis.
 Use in an interlock circuit, which requires the provision of double interlock for possible failure by using a
mechanical protective function, and periodical checks to confirm proper operation.

- 4 -
No.EX##-OML0005
Warning
 Do not disassemble, modify (including change of printed circuit board) or repair this product.
Injury or failure can result.
 Do not perform operation or setting with wet hands.
There is a risk of electric shock.
 Do not operate the product beyond the specification range.
Do not use the product for flammable or harmful gases or liquids.
Fire, malfunction or equipment damage may result.
Please confirm the specifications before use.
 Do not operate the product in an environment where flammable or explosive gases may be
present.
Fire or an explosion can result.
The product is not designed to be explosion proof.
 The following instructions must be followed when using the product in an interlocking circuit:
 Provide a multiple interlocking system, such as a mechanical protection system.
 Check the product regularly to ensure proper operation.
Otherwise malfunction can result, causing an accident.
 The following instructions must be followed during maintenance:
 Turn off the power supply.
 Stop the air supply, exhaust the residual pressure and verify that the air is released to
atmosphere before performing maintenance.
Otherwise injury can result.
Caution
 The product is provided for use in manufacturing industries.
The product herein described is basically provided for peaceful use in manufacturing industries.
If considering using the product in other industries consult SMC beforehand and exchange specifications
or a contract if necessary.
If anything is unclear, contact the nearest sales branch.
 When handling, assembling and replacing the unit:
 Do not touch any sharp metal parts of the connector or plug.
 Do not apply excessive force to the unit.
The connecting portions of the unit are firmly joined with seals.
 When joining units, take care not to get fingers caught between units.
Injury can result.
 Perform a proper functional check after completing maintenance.
 Stop operation if the equipment does not function properly.
Safety cannot be assured due to unexpected malfunction.
 Provide grounding to assure the safety and noise immunity of the fieldbus system.
Individual grounding should be provided close to the product with an earth cable as short as possible.

- 5 -
No.EX##-OML0005
Caution
 Follow the instructions given below when handling the fieldbus system.
Failing to do so may result in product damage.
 Operate the fieldbus system within the specified voltage.
 Maintenance space should always be provided around the product.
 Do not remove labels from the product.
 Do not drop, hit or apply excessive shock to the product.
 Follow all specified tightening torques.
 Do not bend, apply tensile force, or apply force by placing heavy loads, on the cables.
 Connect wires and cables correctly, and do not connect while the power is ON.
 Do not route wires and cables together with power or high-voltage cables.
 Separate the power line for solenoid valves from the power line for the input and control units.
 Check the insulation of wires and cables.
 Take proper measures against noise, such as noise filters, when the product is incorporated in
equipment or devices.
 Select the required protection (IP) rating according to the environment of operation.
 Take sufficient shielding measures when the product is to be used in the following conditions:
 where noise due to static electricity is generated.
 where electro-magnetic field strength is high.
 where radioactivity is present.
 where power lines are located.
 Do not use the product in a place where electric surges are generated.
 Use suitable surge protection when a surge generating load such as a solenoid valve is to be
directly driven.
 Prevent any foreign matter from entering this product.
 Do not expose the product to vibration or impact.
 Do not use the product in an environment that is subject to a temperature cycle.
 Use the product within the specified ambient temperature range.
 Do not expose the product to any heat radiation.
 Do not clean the product with chemicals such as benzene or thinners.
 Do not mount in a location where the product will be used as a foothold.
 When lifting a large size solenoid valve manifold unit, take care to avoid causing stress to the valve
connection joint.
 Be careful regarding the inrush current generated when the power is supplied.
 The product does not have resistance against lightning surges required for CE marking; ensure
measures are taken against lightning surge on the equipment side.
 Setting the switches
 Set the switches using a small screwdriver.
When operating the switches, do not touch parts other than the related parts.
This may lead to failure due to component damage or short-circuit.
 Perform switch setting appropriate to the operating conditions.
Inappropriate settings can cause defective operation.
 Please refer to the “Setting and adjustment” section of this document for setting the switches.
 Please refer to the PLC manufacturer’s manual for details of programming and addresses.
For the PLC protocol and programming refer to the relevant manufacturer’s documentation.

- 6 -
No.EX##-OML0005
Note
 Operator
 This operation manual has been written for those who have knowledge of machinery and
apparatus that use pneumatic equipment and have full knowledge of assembly, operation and
maintenance of such equipment.
 Please read this operation manual carefully and understand it before assembling, operating or
providing maintenance.
 Power supply
 Use the following UL recognized direct-current (DC) power supply.
 Limited voltage current circuit in accordance with UL508
A circuit whose power is supplied by secondary coil of an isolating transformer that meets the following
conditions
Maximum voltage (with no load): less than 30 Vrms (42.4 Vpeak)
Maximum current:
 Less than 8 A (including when short circuited)
 Limited by circuit protector (such as a fuse) with the following ratings
No load voltage (Vpeak) Max. current rating (A)
0 to 20 [V] 5.0
Above 20 to 30 [V] 100 / peak voltage
 A circuit using max. 30 Vrms (Class-2 circuit), whose power is supplied by Class-2 power supply unit in
accordance with UL1310 or by Class-2 power supply unit in accordance with UL1585
 The reference for the both the output and control power supplies of the SI unit is 0 V.
+24 V
0 V
Power for output
Power for input and
control
Power for output
Power for input and
control
+24 V
+24 V
0 V
-24 V

- 7 -
No.EX##-OML0005
Product Outline
 System configuration
The EX600 range of units can be connected to various types of fieldbus to achieve the reduction of I/O
device wiring and the use of a distributed control system. The unit communicates with the fieldbus through
the SI unit. One SI unit can be connected with manifold valves with upto 32 points and I/O units with a
maximum 10 points.
All wiring between devices should use cables with suitable connectors at both ends to ensure the system is
compliant to IP67 protection.
 SI unit: Performs fieldbus communication and solenoid valve manifold ON/OFF output.
 Digital input unit: For connecting sensors with switch output capability. PNP and NPN types are available.
 Digital output unit: For connecting output equipment such as solenoid valves, lamps, buzzers, etc. PNP
and NPN types are available.
 Analog input unit: For connecting sensors with analogue output capability.
 Endplate: Connected at the D side of the EX600 manifold, incorporating the power supply connection.
 Solenoid valve manifold: An assembly of solenoid valves. One connector is used as the electric
connection to all connected valves.
Endplate
SI Unit
Digital Input
Unit
Digital Outpu
t
Uni
t
A
nalog
Input Uni
t
Manifold
Valve U Side
D Side

- 8 -
No.EX##-OML0005
 Glossary
No. Term Definition
A Address
(Station address)
Number allocated to identify each unit connected on PROFIBUS DP network. Address number is not
permitted to be duplicated.
C Communication speed
Data receive and transmit speed used by the fieldbus. This depends on master equipment (PLC etc.),
the unit used is bps (bit per second).
C Current consumption The amount of current required by each unit in order to operate.
D Diagnostic information
Diagnostic information consisting of standard diagnostic information from both the PROFIBUS DP and
the EX600.
D DIN rail Metal rail in accordance with the DIN standard.
D D side The DOWN side of the manifold, where EX600 end plate is connected
F FAIL SAFE function When PLC (DP master) is at clear mode, it sends data packet of output data with data length =“0”. As
a result the slave will be set to a defined state (Hold/Clear/Force ON).
F FE Functional Earth.
F Fieldbus Type of communication system between a PLC and factory equipment (such as measuring
instruments or machines), in which data is exchanged by digital communication.
F FREEZE function Function that synchronizes input data of SI unit with FREEZE Command from PLC (DP master).
G GSD file General Station Description file. This is a file that describes the product characteristics for
configuration with PROFIBUS DP system.
H Hand-held terminal
(HT)
A unit to connect with the SI unit PCI connection, for parameter adjustment, to monitor all input and
output signal status, and for Forced input/output selection.
I ID No. 16 bit number which is assigned by PNO to identify the product
I Idle Condition when SI unit (PROFIBUS DP) receives FAIL SAFE command. Using parameter setting,
output can be set to CLEAR/HOLD/Force ON.
I Input points Number of points that which can receive information from input equipment. (Sensor and switch, etc.)
M Manifold An assembly with many openings for receiving and distributing fluid or gas.
N NPN output Output that switches a load through an NPN transistor. The +ve side of the load is connected to a
common +ve. For this reason, NPN output is often referred to as “common positive”.
N NPN input Input that receives data from sensor with an NPN output signal.
O Open circuit detection Diagnostic function that detects open circuit, caused by broken or disconnected wiring to the
input/output equipment.
O Output points Number of points of output equipment (Solenoid Valve, lamp, motor starter, etc.), which can be
operated.
P PLC Programmable Logic Controller. A Controller which performs sequential control using programs of
logical, order and arithmetic operation, etc.
P PNP output Output that switches a load through a PNP transistor. The –ve side of the load is connected to the 0 V
common return. For this reason, PNP output is often referred to as “common negative”.
P PNP input Input that receives data from sensor with PNP output signal.
P PROFIBUS DP Fieldbus that Siemens, Bosch, and ABB, etc. jointly developed in Germany in 1980's. PNO
(PROFIBUS Nutzerorganisation e.V.) is started in order to spreads the PROFIBUS.
P Protection class
(IP□□)
International Protection Rating. A Standard related to protection against foreign objects into electrical
enclosures. (Hand, wire, dust, and water, etc.)
S Short circuit detection Function that detect if output or power supply positive line is short circuited with GND, thus over
current state has occurred.
S Short circuit protection Internal circuit protection to prevent damage by over current caused by power supply positive line
being short circuited with GND
S SI unit Serial Interface unit. A unit for connection with a PLC to perform input/output data
communication.
S SYNC function Function that synchronizes output data of the SI unit with a SYNC command from a PLC (DP master).
T Terminating resistance
When connecting devices to the fieldbus, resistance must be installed on both ends of the wiring
system. This prevents signal reflection and maintains data integrity.
U U side The UP side of the manifold, where solenoid valve manifold is connected.

- 9 -
No.EX##-OML0005
Assembly
 Assembling the unit as a manifold.
*: If the unit was purchased as a manifold, the work described in this section is not necessary.
Note
 Be sure to turn off the power when carrying out work to assemble the unit as a manifold.
 Connect a unit to the end plate.
Digital input units, digital output units and analogue units can be connected in any order.
(Tightening torque: 1.5 to 1.6 N•m)
 Add more units
Upto 10 units, including the SI unit, can be connected to one manifold.
 Connection of SI unit
Connect the SI unit after connecting all of the required I/O units together. The connection procedure is the
same as above.

- 10 -
No.EX##-OML0005
 Mounting the valve plate
Mount the valve plate to the manifold valve with valve fixing screws.
(Tightening torque: 0.6 to 0.7 N•m)
 Connect the SI unit to the manifold valves.
Insert the valve plate into the valve plate mounting groove at the side of the SI unit. Fix using the valve plate
fixing screws. (Tightening torque: 0.7 to 0.8 N•m)
Note
 Please do not connect the unit while the power supply is ON.
It will cause equipment damage
Set screw mountings
SV:
S070:
VQC1000:
2 places
VQC2000: 3 places
VQC4000: 4 places

- 11 -
No.EX##-OML0005
Mounting and Installation
 Installation method
 Direct mounting
When joining six or more units, fix the middle part of the complete EX600 unit with an intermediate
reinforcing brace (EX600-ZMB1) before mounting (Refer to the figure below.) using 2xM4 screws
(Tightening torque: 0.7 to 0.8 N•m)
Intermediate reinforcing brace
(
EX600-ZMB1
)
Fix and tighten the end plate at one end of the unit as shown in the figure below.
(Tightening torque: 0.7 to 0.8 N•m)
Fix the end plate at the valve side after referring to the manual of the corresponding manifold valve.
2 M4 screws
(tightening torque: 0.7 to 0.8 Nm)
End plate Manifold valve
Intermediate reinforcing brace
2 M4 screws
117 0.2
90 0.2
23.5
47xn
5.5
826
8
47
47xm
(Tolerance: 0.2 mm
)
2 x M4 screws
(Tightening torque: 0.7 ~ 0.8 N•m)
Intermediate reinforcing brace
2 x M4 screws
(Tolerance: ±0.2 mm)

- 12 -
No.EX##-OML0005
 DIN rail mounting
 When joining five or more units, fix the middle part of the complete EX600 unit with an intermediate
reinforcing brace (EX600-ZMB2) before mounting, using 2xM4 screws.
(Tightening torque: 0.7 to 0.8 N•m)
 Mount the end plate bracket (EX600-ZMA2) to the end plate, using 2xM4 screws.
(Tightening torque: 0.7 to 0.8 N•m)
2
End plate bracket
(EX600-ZMA2)
1
Intermediate reinforcing
brace (EX600-ZMB2)
 Hook the DIN rail mounting groove onto the DIN rail. (See the figure below.)
 Press the manifold using the side hooked onto the DIN rail as a fulcrum until the manifold is locked.
 Fix the manifold by tightening the DIN rail fixing screws of the EX600-ZMA2.
(Tightening torque: 0.7 to 0.8 N•m)
The tightening torque at the valve side depends on the valve type.
DIN rail
Fulcrum
4 3,
5
End plate bracket
(EX600-ZMA2)
2 x M4
screws 2 x M4
screws

- 13 -
No.EX##-OML0005
 SPEEDCON wiring method
The M12 connector can be mated with a SPEEDCON connector.
 Set the projected portion of the cable connector metal ring (plug /socket) to the mark at cable end.
 Push the connector straight to insert it into the receptacle of the unit. If inserted without aligning the mark,
the connector will not mate with the receptacle.
 Turn the connector clockwise. It stops when turned 1/4 turn. Turn it further. When the connector is turned
1/2 turn from the original position, the projected portion is set at the diagonal position to the mark and the
turn is completed. Check that the connector is securely locked. If the connector is turned excessively, it
will become difficult to remove.
Mark at cable end
Mark on the unit
Projected
portion
Turn-lock
mechanism of the
connecto
r

- 14 -
No.EX##-OML0005
 Mounting the marker
Mount the marker (EX600-ZT1) into the marker groove as required.
SI Unit
How to order
EX600 – S
SIUnit Outputpolarity
Protocol
Name and function of the parts
1
11
234
5
6
7
8
9
10
No Name Description
1 Status LED
Indicates the unit status. (Refer to the
“Error display” section for further
details.)
2 Display cover Open to gain access to the setting
switches.
3 Display cover set
screw Loosen to open the display cover.
4 Connector (BUS
OUT) (socket)
Connector for fieldbus output.
BUS IN and BUS OUT are connected
inside the unit.
5 Marker groove Groove to mount a marker.
6 Connector For handheld terminal. (Socket)
7 Valve plate
mounting holes Holes for fixing the valve plate.
8 Valve plate
mounting groove Groove for mounting the valve plate.
9 Joint bracket Joint bracket to join the adjacent unit,
fixed with attached screws.
10 Connector for unit
(plug)
Conveys the signals and power
supplies to the adjacent unit.
11 Connector
(BUSIN) (plug)
Connector for fieldbus input.
BUS IN and BUS OUT are connected
inside the unit.
Symbol Description
1 PNP (-COM.)
2 NPN (+COM.)
Symbol Description
PR PROFIBUS DP

- 15 -
No.EX##-OML0005
• Display and description
Mounting and installation
 Connection
Configuration
Pin No. Signal name Wire colour BUS IN BUS OUT
1 NC -
2 RXD/TXD-N Green
3 NC -
4 RXD/TXD-P Red
5 Shield Shield
12
34
5
12
34
5
The branch connection is arranged in the EX600-SPR1/2 as illustrated on the circuit below.
When connecting other PROFIBUS DP products, connect using the BUS OUT connector, to increase the
number of PROFIBUS DP slave stations.
Note
 Be sure to place a seal cap
on any unused connectors.
 Placing the seal cap
appropriately enables the
unit to achieve IP67
protection.
Label Description
ST(M) Unit diagnostic status
PWR Displays the control and input power supply
voltage status
PWR(V) Displays the output power supply voltage
status
SF System fault
BF Bus fault

- 16 -
No.EX##-OML0005
 Transmission distance
For communication wiring, PROFIBUS DP compatible shielded twisted pair cable must be used. The
longest permissible cable length depends on transmission speed and type of cable used.
The table below gives data for when type A cable is used.
Communication
speed [kbps] 9.6 19.2 45.45 93.75 187.5 500 1500 3000 6000 12000
Cable length [m] 1200 1000 400 200 100
Setting and adjustment
 Setting procedure
 Loosen the screw for the switch protection cover (indicated with an arrow).
 Open the cover with a flat blade screwdriver.
Set switches as stated in the following pages.
Use a small point precision screwdriver to set switches.
 After setting the switches replace the switch protection cover and tighten the screw.
(Tightening torque: 0.3 to 0.4 N•m)
Note
 When adjusting the switch, make sure not to touch
other parts other than the setting switch. Failure can
be caused by damaged parts or short circuit.
 Ensure the power is turned OFF before setting
switches.
 All switches are set to OFF or 0 when delivered
(factory setting). Perform the switch settings before
use.
 When foreign matter or water droplets are observed
near the switch protection cover clean and dry area
before opening the cover.
 Address setting switch
ON
12345678
AddressTerminator
Settin
g
2
Setting1
×10 ×1
ON
1234
0
1
2
3
4
5
6
7
8
9
0
1
2
3
4
5
6
7
8
9
Address setting switch (x1): To set PROFIBUS DP node address units digit.
Address setting switch (x10): To set PROFIBUS DP node address tens digit.
Setting2 (No.8) switch: To set PROFIBUS DP node address hundreds digit.
2
1
Setting 1 Terminator Address
Setting2

- 17 -
No.EX##-OML0005
 Address Setting
Setting2 Address SW
No. 8 x10 x1 Node address
0 0 0 (factory default)
0 1 1
0 2 2
… … …
9 8 98
OFF
9 9 99
0 0 100
0 1 101
… … …
ON
2 6 126
Note) If the address is set to 0 or number greater than 126, an error will result and “SF” and “BF” LEDs will
flash.
 Setting 1 switch
ON
12345678
AddressTerminator
Settin
g
2
Setting1
×10 ×1
ON
1234
0
1
2
3
4
5
6
7
8
9
0
1
2
3
4
5
6
7
8
9
V_SEL switch: A function to select the number of points occupied by valve outputs.
 Select the output points (size) occupied by the SI unit.
Setting 1
No. 1 No. 2 Description SI unit output data size
OFF OFF Occupied bit for valve output is 32 4 byte (factory default)
OFF ON Occupied bit for valve output is 24 3 byte
ON OFF Occupied bit for valve output is 16 2 byte
ON ON Occupied bit for valve output is 8 1 byte
Note) Please set the number of occupied valve points to more than the connected number of valves.
 Baud Rate switch: Switches to set the baud rate of internal communication.
Setting 1
No. 3 No. 4 Description
OFF OFF 1 Mbps (factory setting)
OFF ON 500 kbps
ON OFF 250 kbps
ON ON 125 kbps
Note) 500, 250 & 125 kbps settings are for future extension. Please use 1 Mbps (factory default setting).
Setting 1 Terminator Address
Settin
g
2

- 18 -
No.EX##-OML0005
 Setting 2 switch
ON
12345678
AddressTerminator
Setting2
Setting1
×10 ×1
ON
1234
0
1
2
3
4
5
6
7
8
9
0
1
2
3
4
5
6
7
8
9
HOLD/CLR switch: When a fieldbus communication error occurs or when communication stops, all output
can be set to Hold or Clear.
Set the status of this switch in parameters. (Refer to “Parameter settings”)
Setting 2
No.4 Description
OFF All outputs are cleared “0” when a communication error occurs.
(Factory setting)
ON All outputs are held when a communication error occurs
 Terminator switch
ON
12345678
AddressTerminator
Setting2
Setting1
×10 ×1
ON
1234
0
1
2
3
4
5
6
7
8
9
0
1
2
3
4
5
6
7
8
9
Terminator switch: Set the terminator resistance of the PROFIBUS communication line.
Note
 When this unit is connected at the end of the
PROFIBUS DP line, make sure to set to [Terminator
Resistance fitted]
Terminator resistance value depends on the
specification of the cable used. The terminator
resistance value is fitted to suit the type A cable.
Terminator setting
Terminator
resistance
fitted
No terminator
resistance
(factory
default)
No terminator
resistance
Setting 1 Terminator Address
Settin
g
2
Setting 1 Terminator Address
Setting 2

- 19 -
No.EX##-OML0005
Error display
 Common for SI Units
LED status Descriptions
Power for control/input is OFF.
Unit is operating normally.
Component failure inside SI unit.
When ST(M) indicator is red, stop using the product and contact SMC.
•Valve is in short circuit or open circuit.
•Valve ON/OFF counter has exceeded the set value.
Communication error between units.
Check the connection between units.
Error diagnostic detected the error of a unit other than the SI unit.
Abnormal power voltage for control/input.
Check the power supply and adjust or replace it.
Abnormal power voltage for output.
Check the power supply and adjust or replace it.
Symbol Status Symbol Status
Light OFF Flashing red light
Red light ON
Flashing red/green light
(Alternate: frequency 1 s)
Green light ON Flashing green light

- 20 -
No.EX##-OML0005
 PROFIBUS DP
LED status Descriptions
Normal status with established communication with DP master, or power for control/input is
OFF.
SI unit recognized the communication speed but DP master address setting is wrong.
Check and correct the address setting
Any one of the following:
•No connection between DP master and SI unit.
•SI unit cannot recognize the communication speed.
•DP master failure or SI unit failure.
Communication established between DP master and SI unit, but with diagnostic error.
Discrepancy between DP master setting and device configuration data.
Check and correct the setting.
SI unit address set to “0” or above “126”. Check and correct the address setting.