SMC Networks EXW1-BMJA Series User manual

No.EX※※-OMZ0016
PRODUCT NAME
Compact Wireless Base
MODEL / Series / Product Number
EXW1-BMJA#
PRODUCT NAME
Compact Wireless Remote
MODEL / Series / Product Number
EXW1-RDXNE4##
EXW1-RDYNE4##
EXW1-RDM#E3##
EXW1-BMJA# EXW1-RD#

-2-
No.EX※※-OMZ0016
Table of Contents
Read before use································································································3
Safety Instructions····························································································3
Limited warranty and Disclaimer/Compliance Requirements ·································4
Important Instructions concerning the Wireless System········································9
SMC Wireless System······················································································ 10
Features and Summary··························································································································10
System Configuration·····························································································································11
System compatibility······························································································································12
How to Order ·······································································································································16
Summary of Product parts ··············································································· 17
EXW1-BMJA*·······································································································································17
EXW1-RD* ··········································································································································20
Setting and Adjustment ··················································································· 26
Flow chart for operating the wireless system·······························································································26
I/O Configurator (NFC version) ················································································································27
Preparation··········································································································································28
Installation of the software ······················································································································28
Before starting the software·····················································································································29
Download the I/O Configurator (NFC version) ·····························································································33
Start the I/O Configurator (NFC version) ····································································································34
Screen Layouts of the I/O Configurator (NFC Version)··················································································35
Monitoring and setting up························································································································37
Setting/Adjustment of the Wireless Unit ·····································································································38
Parameter settings of a Remote (optional)··································································································38
Remote setting ·····································································································································38
Parameter settings of the Base ················································································································40
CC-Link setting·····································································································································40
System setting······································································································································42
Frequency channel select function (F.C.S.)·································································································45
Event··················································································································································47
Wireless··············································································································································49
Pairing and Unpairing Procedures ···································································· 51
Pairing Procedure ·································································································································51
Unpairing Procedure······························································································································56
Mounting and Installation of Units ···································································· 58
EXW1-BMJ*, EXW1-RD*························································································································58
Troubleshooting ····························································································· 61
Technical Information······················································································ 72
I/O Map···············································································································································72
I/O Mapping·········································································································································74
Diagnostics Mapping ·····························································································································74
I/O Mapping Order When EX600-WSV* Is Paired ························································································75
I/O Mapping Order When EX600-WEN* or EX600-WPN* Is Paired··································································79
Diagnostics map details··························································································································85
Specifications································································································· 92
Dimensions··········································································································································92
Specifications Table·······························································································································94
Accessories ··································································································· 98
Accessory List······································································································································98

-3-
No.EX※※-OMZ0016
Read before use
Safety Instructions
These safety instructions are intended to prevent hazardous situations and/or equipment damage.
These instructions indicate the level of potential hazard with the labels of "Caution", "Warning" or "Danger".
They are all important notes for safety and must be followed in addition to International Standards
(ISO/IEC)*1), and other safety regulations.
*1) ISO 4414: Pneumatic fluid power -- General rules relating to systems.
ISO 4413: Hydraulic fluid power -- General rules relating to systems.
IEC 60204-1: Safety of machinery -- Electrical equipment of machines. (Part 1: General requirements)
ISO 10218: Manipulating industrial robots -Safety.
etc.
Caution
Caution indicates a hazard with a low level of risk which, if not avoided, could
result in minor or moderate injury.
Warning
Warning indicates a hazard with a medium level of risk which, if not avoided,
could result in death or serious injury.
Danger
Danger
indicates a hazard with a high level of risk which, if not avoided, will
result in death or serious injury.
Warning
1. The compatibility of the product is the responsibility of the person who designs the
equipment or decides its specifications.
Since the product specified here is used under various operating conditions, its compatibility with
specific equipment must be decided by the person who designs the equipment or decides its
specifications based on necessary analysis and test results.
The expected performance and safety assurance of the equipment will be the responsibility of the
person who has determined its compatibility with the product.
This person should also continuously review all specifications of the product referring to its latest catalog information,
with a view to giving due consideration to any possibility of equipment failure when configuring the equipment.
2. Only personnel with appropriate training should operate machinery and equipment.
The product specified here may become unsafe if handled incorrectly.
The assembly, operation and maintenance of machines or equipment including our products must be
performed by an operator who is appropriately trained and experienced.
3. Do not service or attempt to remove product and machinery/equipment until safety is confirmed.
1. The inspection and maintenance of machinery/equipment should only be performed after measures
to prevent falling or runaway of the driven objects have been confirmed.
2. When the product is to be removed, confirm that the safety measures as mentioned above are
implemented and the power from any appropriate source is cut, and read and understand the specific
product precautions of all relevant products carefully.
3. Before machinery/equipment is restarted, take measures to prevent unexpected operation and malfunction.
4. Contact SMC beforehand and take special consideration of safety measures if the
product is to be used in any of the following conditions.
1. Conditions and environments outside of the given specifications, or use outdoors or in a place
exposed to direct sunlight.
2. Installation on equipment in conjunction with atomic energy, railways, air navigation, space, shipping,
vehicles, military, medical treatment, combustion and recreation, or equipment in contact with food and
beverages, emergency stop circuits, clutch and brake circuits in press applications, safety equipment or
other applications unsuitable for the standard specifications described in the product catalog.
3. An application which could have negative effects on people, property, or animals requiring special
safety analysis.
4. Use in an interlock circuit, which requires the provision of double interlock for possible failure by using
a mechanical protective function, and periodical checks to confirm proper operation.

-4-
No.EX※※-OMZ0016
Read before use
Safety Instructions
Caution
1.The product is provided for use in manufacturing industries.
The product herein described is basically provided for peaceful use in manufacturing industries.
If considering using the product in other industries, consult SMC beforehand and exchange
specifications or a contract if necessary.
If anything is unclear, contact your nearest sales branch.
Limited warranty and Disclaimer/Compliance Requirements
The product used is subject to the following "Limited warranty and Disclaimer" and "Compliance
Requirements".
Read and accept them before using the product.
Limited warranty and Disclaimer
1. The warranty period of the product is 1 year in service or 1.5 years after the product is
delivered, whichever is first.
∗
2)
Also, the product may have specified durability, running distance or replacement parts.
Please consult your nearest sales branch.
2. For any failure or damage reported within the warranty period which is clearly our
responsibility, a replacement product or necessary parts will be provided.
This limited warranty applies only to our product independently, and not to any other
damage incurred due to the failure of the product.
3. Prior to using SMC products, please read and understand the warranty terms and
disclaimers noted in the specified catalog for the particular products.
∗
2) Vacuum pads are excluded from this 1 year warranty.
A vacuum pad is a consumable part, so it is warranted for a year after it is delivered.
Also, even within the warranty period, the wear of a product due to the use of the
vacuum pad or failure due to the deterioration of rubber material are not covered by the
limited warranty.
Compliance Requirements
1. The use of SMC products with production equipment for the manufacture of weapons of
mass destruction (WMD) or any other weapon is strictly prohibited.
2. The exports of SMC products or technology from one country to another are governed by
the relevant security laws and regulation of the countries involved in the transaction. Prior
to the shipment of a SMC product to another country, assure that all local rules governing
that export are known and followed.

-5-
No.EX※※-OMZ0016
Operator
♦This operation manual is intended for those who have knowledge of machinery using
pneumatic equipment, and have sufficient knowledge of assembly, operation and maintenance
of such equipment. Only those persons are allowed to perform assembly, operation and
maintenance.
♦Read and understand this operation manual carefully before assembling, operating or providing
maintenance to the product.
■Safety Instructions
Warning
■Do not disassemble, modify (including changing the printed circuit board) or repair.
An injury or failure can result.
■Do not operate or set with wet hands.
This may lead to an electric shock.
■Do not operate the product outside of the specifications.
Do not use for flammable or harmful fluids.
Fire, malfunction, or damage to the product can result.
Verify the specifications before use.
■Do not operate in an atmosphere containing flammable or explosive gases.
Fire or an explosion can result.
This product is not designed to be explosion proof.
■If using the product in an interlocking circuit:
•Provide a double interlocking system, for example a mechanical system.
•Check the product regularly for proper operation.
Otherwise malfunction can result, causing an accident.
■The following instructions must be followed during maintenance:
•Turn off the power supply.
•Stop the air supply, exhaust the residual pressure and verify that the air is released before performing
maintenance.
Otherwise an injury can result.

-6-
No.EX※※-OMZ0016
Caution
■When handling the unit or assembling/replacing units:
•Do not touch the sharp metal parts of the connector or plug for connecting units.
•Take care not to hit your hand when disassembling the unit.
The connecting portions of the unit are firmly joined with seals.
•When joining units, take care not to get fingers caught between units.
An injury can result.
■After maintenance is complete, perform appropriate functional inspections.
Stop operation if the equipment does not function properly.
Safety cannot be assured in the case of unexpected malfunction.
■Provide grounding to assure noise resistance of the Fieldbus system.
Individual grounding should be provided close to the product with a short cable.
Caution
Notice:
Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the
equipment.
NOTE:
This device complies with the limits for a Class Adigital device, pursuant to part 15 of the FCC Rules.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
This device complies with the Federal Communications Commission (FCC) and Innovation, Science and
Economic Development Canada license-exempt RSS (s).
To operate this device, the following two conditions must be satisfied:
(1) This device does not cause interference.
(2) This device must accept any kind of interferences, including interferences that may cause
unexpected operations.
Caution
When operating this device, follow the safety requirements for radio frequency exposure established by the
Federal Communications Commission (FCC) and Innovation, Science and Economic Development Canada,
and keep the human body (excluding fingers, hands, wrists, ankles, and feet) at least 20 cm away from the
device.
When installing this device, place it 20 cm away from the end user.

-7-
No.EX※※-OMZ0016
■Precautions for Handling
○Follow the instructions given below for selecting and handling.
●The instructions on design and selection (installation, wiring, environment, adjustment, operation,
maintenance, etc.) described below must be followed.
∗Product specifications
•Use within the specified voltage.
Otherwise failure or malfunction can result.
•Reserve a space for maintenance.
Design the system to allow the required space for maintenance.
•Do not remove the label.
This can lead to incorrect maintenance, or misreading of the operation manual, which can cause damage or
malfunction to the product.
It may also result in nonconformity to safety standards.
•Beware of inrush current when the power supply is turned on.
An initial charge current may activate the over current protection function depending on the connected load,
resulting in the unit malfunctioning.
●Product Handling
∗Mounting
•Do not drop, hit or apply excessive shock to the product.
Otherwise damage to the internal parts can result, causing malfunction.
•Tighten to the specified tightening torque.
If the tightening torque is exceeded, the mounting screws can be broken.
If the screws are tightened to a different torque, IP67 will not be achieved.
•Never mount the product in a location that will be used as a foothold.
The product may be damaged if excessive force is applied by stepping or climbing onto it.
∗Wiring (Including connecting/disconnecting of the connectors)
•Avoid bending or stretching the cables repeatedly, or placing a heavy load or apply force to the product.
Applying repeated bending and tensile stress to the cable may cause broken wires.
•Wire correctly.
Incorrect wiring may cause malfunction of or damage to the wireless system.
•Do not perform wiring while the power is on.
Otherwise the wireless system may be damaged or malfunction.
•Do not route wires and cables together with power or high voltage cables.
The product can malfunction due to interference of noise and surge voltage from power and high voltage cables
close to the signal line.
Route the wires of the wireless system separately from power or high voltage cables.
•Confirm correct insulation of wiring.
Poor insulation (interference with other circuits, poor insulation between terminals, etc.) can apply excessive
voltage or current to the wireless system causing damage to it.
•When a wireless system is installed in machinery/equipment, provide adequate protection against noise
by using noise filters, etc.
Noise in signal lines may cause malfunction.

-8-
No.EX※※-OMZ0016
∗Operating environment
•Select the correct type of enclosure according to the operating environment.
IP67 protection class is achieved when the following conditions are met.
(1) The units are connected correctly using power supply cables and communication cables with M12 (or M8)
connectors.
(2) Suitable mounting of each unit and manifold valve.
(3) Be sure to fit a water resistant cap on any unused connectors.
If using in an environment that is exposed to water splashes, please take protective measures, such as using a
cover.
Do not use in an atmosphere having water, water steam, or where there is direct contact with any of these. These
may cause failure or malfunction.
•Do not use the product in a place where the product could be splashed by oil or chemicals.
Operating in environments with coolants, cleaning solvents, various oils or chemicals may cause adverse effects
(failure, malfunction) to the unit even in a short period of time.
•Do not use the product in an environment where corrosive gases or fluids can be splashed.
Otherwise damage to the unit can result, causing malfunction.
•Do not use in an area where surges are generated.
If there is equipment generating large surge near the unit (magnetic type lifter, high frequency inductive furnace,
welding machine, motor, etc.), this can cause deterioration of the internal circuitry element of the unit or result in
damage. Take measures against the surge sources, and prevent the lines from coming into close contact.
•When a surge-generating load such as a relay, valve, or lamp is directly driven, use the product with
built in surge protection.
Direct drive of a load generating surge voltage can damage the unit.
•The product is CE marked, but is not immune to lightning strikes. Take measures against lightning
strikes in the system.
•Prevent foreign matter such as dust or wire debris from entering inside the product.
Otherwise it can cause damage or malfunction.
•Mount the product in a place that is not exposed to vibration or impact.
Otherwise it can cause damage or malfunction.
•Do not use the product in an environment that is exposed to temperature cycles.
Heat cycles other than ordinary changes in temperature can adversely affect the inside of the product.
•Do not expose the product to direct sunlight.
If using in a location directly exposed to sunlight, shade the product from the sunlight.
Otherwise it can cause damage or malfunction.
•Keep within the specified ambient temperature range.
Otherwise malfunction can result.
•Do not operate close to a heat source, or in a location exposed to radiant heat.
Otherwise malfunction can result.
∗Adjustment and Operation
•Perform settings suitable for the operating conditions.
Incorrect setting can cause operation failure.
(Refer to "Setting andAdjustment".)
•Please refer to the PLC manufacturer's manual, etc. for details of PLC-side programming and
addresses.
For the PLC protocol and programming, refer to the relevant manufacturer's documentation.

-9-
No.EX※※-OMZ0016
∗Maintenance
•Turn off the power supply, stop the supplied air, exhaust the residual pressure and verify the release
of air, before performing maintenance.
Otherwise safety is not assured due to an unexpected malfunction or incorrect operation.
•Perform regular maintenance and inspections.
There is a risk of unexpected operation due to malfunction of the equipment.
•After maintenance is complete, perform appropriate functional inspections.
Stop operation if the equipment does not function correctly.
Otherwise safety cannot be assured due to an unexpected malfunction or incorrect operation.
•Do not use solvents such as benzene, thinner, etc. to clean each unit.
These can damage the surface of the body and erase the markings on the product.
Use a soft cloth to remove stains.
For heavy stains, use a damp cloth that has been soaked with diluted neutral detergent and fully squeezed, then
wipe up the stains again with a dry cloth.
Important Instructions concerning the Wireless
System
●The product is certified as wireless equipment in accordance with the Radio Act and the certification of
construction type has been obtained. Customers do not need to apply for a license to use this
equipment.
Be sure to comply with the following precautions.
•Do not disassemble or modify the product. Disassembly and modification are prohibited by law.
•Attach and use the supplied antenna set (EXW1-EA1) as an external antenna.
The law forbids the use of antennas and coaxial cables that are not sold by SMC.
•This product is compliant with the Radio Act in Japan, European countries and the US. For use in
other countries, please consult SMC. For the latest information, refer to the catalog on the website
below.
URL https://www.smcworld.com
●This product communicates using radio waves, and the communication may be temporarily interrupted
due to the ambient environments and operating methods. SMC will not be responsible for any
secondary failure which may cause an accident or cause damage to other devices or equipment.
●When several units are installed close to each other, slight interference may occur due to the
characteristics of the wireless product.
●Radio waves emitted by this product may adversely affect implantable medical devices such as
implantable cardiac pacemakers and brillators.
For precautions regarding the use of equipment or devices that may adversely affect performance,
refer to the catalog or instruction manuals for the equipment or devices, or contact the manufacturers
directly.
●The communication performance is affected by the ambient environment, so please perform
communication testing before use.

-10-
No.EX※※-OMZ0016
SMC Wireless System
Features and Summary
The SMC wireless system is an I/O distributed system which can be wirelessly connected.
It consists of a combination of a Base that has a function to communicate with the upper-level device (such
as a PLC) or a Base that has a wireless communication function and Remotes.
From an upper-level (PLC) control component, a Base appears to be a single system including Remotes
paired with it, and up to 896 inputs and 896 outputs can be handled per system.
Bases and Remotes are designed to be identifiable by registering their uniquely assigned PIDs (Product IDs)
with each other and operate without malfunctioning even when several Bases and Remotes operate in the
same area.
The packet of the wireless transmit and receive data is encrypted. It is therefore difficult to manipulate the
data.
The SMC wireless system has the following features.
•Quick start-up takes 0.25 sec. (minimum) to connect to the system when the Remote is powered. *1
•Parameter setting by Near Field Communication (NFC) using a PC (no HW setting).
•The maximum number of inputs/outputs of the system is 896/896*2, 3
•Up to 15 CC-Link Ver1.10 Remotes or 127 Ver2.00 Remotes can be registered per Base*4
*1: The Base is in start-up mode, and will change depending on the Remote power-on timing and external influences.
*2: The maximum number of inputs/outputs is 896/896. If there are more than 896 inputs or outputs, they are not recognized.
There might be communication delay depending on the communication load status.
*3: Total number of Remote inputs/output registered in the Base.
*4: The maximum number of units that can be connected is 127. If 127 units is exceeded, the unit I/O will not be recognized.
There might be communication delay depending on the communication load status.

-11-
No.EX※※-OMZ0016
System Configuration
For settings and other information, refer to the operation
manuals for EX600-WSV* and the connected digital and
analog units.
CC-Link
compatible
PLC
Connected input/output devices
<Base>
<Remote>
EXW1 series
EX600-W Series
EXW1 series
EX600-W Series
For settings and other information, refer to
the operation manual for EX600-
WEN/WPN*.
EtherNet/IP
PROFINET
compatible
PLC

-12-
No.EX※※-OMZ0016
System compatibility
Mixed use with EX600-W Series
Although it is possible to use with EX600-W series, the operating conditions must comply with the
specifications of the existing wireless system. Note that the following functions may be restricted:
•Communication distance
•Protocol
This refers to a wireless communication version. For more details, check the system settings of the
Base.
•Frequency channel select function (F.C.S.)
The frequency channel to use can be selected using this function.
* The number of selectable frequency channels varies depending on the country of use.
For more details, check the product number.
●Countries other than the US, Canada and South Korea: ch 5-79
●US, Canada and South Korea: ch 15-79
* If no channel is selected, communication is established on ch 79 by default.
Below is a conceptual diagram.
•WEB function (supported only by EX600-WEN/WPN)
Various product settings and communication statuses can be checked by accessing EX600-WEN/WPN
from a PC.
1ch to 79ch
Communication is established only on frequency
channels selected using F.C.S.
No communication
Frequency channel
No communication
Frequency channel

-13-
No.EX※※-OMZ0016
Refer to the system configuration example below.
System configuration example
Applicable function
No. Wireless
Base Wireless Remote Communication distance Protocol
Frequency
channel
select function
(F.C.S.)
WEB
function
1 EXW1 EXW1 Up to 100 m V.1.0/V.2.0*1 Available*2 -
2 EXW1 EXW1+EX600 *3 V.1.0 NA -
3 EXW1 EX600 Up to 10 m V.1.0 NA -
4 EX600 EXW1 Up to 10 m V.1.0 NA Available*4
5 EX600 EXW1+EX600 Up to 10 m V.1.0 NA Available*4
6
*5
EX600
EX600
Up to 10 m
V.1.0
NA
Available
*1: For more details, check the system settings of the Base.
*2: Available in Protocol V.2.0.
*3: Up to 100 m between an EXW1 series Base and Remote, and up to 10 m between an EXW1 series Base
and an EX600-W series Remote.
*4: The settings and monitor function are restricted when communication is established between EX600-
WEN/WPN and EXW1-R*.
*5: This configuration consists solely of EX600-W series units; refer to the operation manual for the product
in use.
○ System configuration example 1
Wireless Base: EXW1-BMJA*
Wireless Remote: EXW1 series
<Wireless Base>
<Wireless Remote>

-14-
No.EX※※-OMZ0016
○ System configuration 2
Wireless Base: EXW1-BMJA*
Wireless Remote: EXW1 series, EX600-W series
○ System configuration 3
Wireless Base: EXW1-BMJA*
Wireless Remote: EX600-W
<Wireless Base>
<Wireless Remote>
EXW1 series
EX600-W Series
<Wireless Base>
<Wireless Remote>
EX600-W Series

-15-
No.EX※※-OMZ0016
○ System configuration 4
Wireless Base: EX600-W series
Wireless Remote: EXW1 series
○ System configuration 5
Wireless Base: EX600-W series
Wireless Remote: EXW1 series, EX600-W series
<Wireless Base>
EX600-W Series
<Wireless Remote>
<Wireless Base>
EX600-W Series
<Wireless Remote>
EXW1 series
EX600-W Series

-16-
No.EX※※-OMZ0016
○ System configuration 6
Wireless Base: EX600-W series
Wireless Remote: EX600-W series
For system configurations of EX600-W series, refer to the operation manual for the product in use.
How to Order
The product system, model names and part numbering system of SMC wireless systems are as follows.
<Compact wireless Base>
This product line-up consists of four models, namely EXW1-BMJAAE, EXW1-BMJAAN, EXW1-BMJABE and
EXW1-BMJABN.
<Compact wireless Remotes>
This product line-up consists of 16 models, namely EXW1-RDXNE4AE, EXW1-RDXNE4AN, EXW1-
RDXNE4BE, EXW1-RDXNE4BN, EXW1-RDYNE4AE, EXW1-RDYNE4AN, EXW1-RDYNE4BE, EXW1-
RDYNE4BN, EXW1-RDMPE3AE, EXW1-RDMPE3AN, EXW1-RDMPE3BE, EXW1-RDMPE3BN, EXW1-
RDMNE3AE, EXW1-RDMNE3AN, EXW1-RDMNE3BE and EXW1-RDMNE3BN.
EXW1-BMJAAE E
EXW1-BMJAAN N
EXW1-BMJABE E
EXW1-BMJABN N
EXW1-RDXNE4AE E
EXW1-RDXNE4AN N
EXW1-RDXNE4BE E
EXW1-RDXNE4BN N
EXW1-RDYNE4AE E
EXW1-RDYNE4AN - N
EXW1-RDYNE4BE E
EXW1-RDYNE4BN N
EXW1-RDMPE3AE E
EXW1-RDMPE3AN N
EXW1-RDMPE3BE E
EXW1-RDMPE3BN N
EXW1-RDMNE3AE E
EXW1-RDMNE3AN N
EXW1-RDMNE3BE E
EXW1-RDMNE3BN N
B
DM
P
E3
A
B
N
A
B
B
Remote
R
DX
N
E4
A
B
DY
A
A : Internal Antenna
B : External Antenna
E : Except USA , Canada and Korea
N : USA , Canada and Korea
Base
EXW1
B
MJ
A
A
DM : Digital Input/Output
N : NPN type
P :PNP type
A : M12 connector
E4 : e-CONconnector(16 points、2 points/connector
E3 : e-CONconnector(8 points、2 points/connector
EXW1 : Product series
B : Wireless Base
R : Wireless Remote
MJ : CC-Link
DX :DigitalInput
DY: Digital Output

-17-
No.EX※※-OMZ0016
Summary of Product parts
EXW1-BMJA*
Appearance
No.
Name
Application
1
Screw hole for mounting
(2 x M4)
Mounting the compact wireless Base.
2
RF (SMA coaxial connector)
* Exclusive to external
antenna versions
Connector for the coaxial cable of an external antenna.
3
BUS IN connector
Connector for a CC-Link communication device.
4 BUS OUT connector
Connector for an additional CC-Link communication device.
* Or it is connected with a terminal resistor.
5
Power supply connector
Supplies power to the compact wireless Base.
6
FE terminal
To be connected to Ground (for improved noise immunity).
7
LED
Indicates the status of the compact wireless Base or Remote.
8
NFC antenna approach
area
This area is in close contact with the NFC reader / writer.
"○" is the center of the NFC antenna.
* Grounding should be as close as possible to the product and the grounding wire should be as short as
possible.
①
②
③
④
⑥
⑤
①
⑦
⑧

-18-
No.EX※※-OMZ0016
LED
The LED indicators at the top left corner of the compact wireless Base indicate the power supply,
communication and diagnostic status.
LED indicators of the compact wireless Base
LED
name Function
LED status
Description
Colour of
LED
ON/Flashing
LRUN Data link status
indication
Green
ON
Communication is normal
- OFF
Communication is not established or the US1 (for control)
power supply is OFF
LERR Error status indication
Red
ON
A communication error has occurred
-
OFF
No communication error
PWR
US1 (for control) power
supply status indication
Green
ON
The US1 (for control) power supply is ON
-
OFF
The US1 (for control) power supply is OFF
MS Base system
status indication
Green
ON
The compact wireless Base is operating normally
Red Flashing
Recoverable error is detected.
(LED flashes when more than one diagnostic information
item is detected.)
•US1 (for control) power supply voltage level is abnormal
•Number of system inputs/outputs setting error
•Network setting error
•Abnormal number of registered Remotes
Red
ON
Unrecoverable error is detected.
-
OFF
The US1 (for control) power supply is OFF
W-SS Radio wave receiving
intensity
Green ON
The level of received radio wave power of all the connected
Remotes is 3
Green
Flashing
(1 Hz)
The level of received radio wave power of some connected
Remotes is 2
Green
Flashing
(2 Hz)
The level of received radio wave power of some connected
Remotes is 1
Red Flashing
All the Remotes that support protocol V.1.0 are not
connected
Orange Flashing
All the Remotes that support protocol V.2.0 are not
connected
-
OFF
Remote not registered
W-NS
Wireless
communication
connection status
indication
Green
ON
All the Remote connections are normal
Green
Flashing
Some Remotes are not connected
Red
Flashing
No Remotes are connected
Red ON
No Remotes are connected
(Unrecoverable error in wireless communication)
Red Green
Alternate
Flashing
Wireless communication connection is being configured
(Pairing)
-
OFF
Remote not registered
W-MS Remote system status
indication
Green
ON
Wireless Remote is normal
Red Flashing
Recoverable error is detected.
(LED flashes when more than one diagnostic information
item is detected.)
•US1 (for control / input) power supply voltage level is
abnormal
•US2 (for output) power supply voltage level is abnormal
•Excessive I/O setting inputs/outputs
•Analog I/O upper setting limit exceeded
•Analog input range upper and lower limits exceeded
•Error in communication between units
•EX600 I/O unit detects diagnostic information
•Valve diagnostic information detected
Red
ON
Unrecoverable error is detected.
-
OFF
Remote not registered

-19-
No.EX※※-OMZ0016
Connectors
•Power supply connector
No. Signal
M12, 4-pin, plug
B code
1 24V (US1)
2
N.C.
3
0V (US1)
4
N.C.
Caution
Note that connecting the power cable to BUS IN or BUS OUT will damage the product.
•BUS IN / BUS OUT connectors
No.
BUS IN
No.
BUS OUT
Signal M12, 4-pin, plug Signal M12, 5-pin , socket
A code
A code
1
SLD
1
SLD
2
DB
2
DB
3
DG
3
DG
4
DA
4
DA
5
N.C.
The signal line of this product is T-branched inside the Base as shown in the circuit diagram below.
When expanding the system, an additional CC-Link remote device can be connected to BUS OUT.
•Circuit diagram
●Precautions for Handling
•Be sure to connect terminal resistors to both ends of the CC-Link main line.
Type of cable Resistance
value
Terminating resistor model no. (Manufacturer)
Communication cable for CC-Link
PCA-1567720 (socket)
PCA-1567717 (plug)
110Ω 1/2
W
•VA-4DCC-110 (Correns)
•CC100 (Woodhead Japan)
CC-Link dedicated high-
performance cable
130 Ω 1/2
W
•VA-4DCC-130 (Correns)

-20-
No.EX※※-OMZ0016
EXW1-RD*
Appearance
EXW1-RDX*B*
No.
Name
Application
1
Screw hole for mounting (M4)
Mounting the compact wireless Remote.
2
PWR (Power connector)
Supplies power to the compact wireless Remote.
3
RF (SMA coaxial connector)
* Exclusive to external antenna
versions
Connector for the coaxial cable of an external antenna.
4
Fn (Pairing button)
Press the button when switching to pairing mode.
5 NFC antenna approach area
This area is in close contact with the NFC reader / writer.
"○" is the center of the NFC antenna.
6
LED
Indicates the status of the compact wireless Remote.
7
FE terminal, screw hole for
mounting (M4)
To be connected to Ground (for improved noise immunity).
This doubles as a screw hole for mounting.
8
Connector for an input device
x 8
Connector for an input device. (PIN2, PIN4: input)
①
⑤
②
③
④
⑥
⑦
⑧