Smith MV1000 User manual

3A5576F
Parts/
Operation
MV1000
Vacuum for collection of dry concrete and asphalt dust. For professional use only.
Important Safety Instructions
Read all warnings and instructions in this manual before using the
equipment. Be familiar with the controls and the proper usage of the
equipment.Save these instructions.

Contents
Warnings .....................................................................................................................................3
Technical Data ............................................................................................................................6
Troubleshooting..........................................................................................................................6
Setup...........................................................................................................................................6
Operation ....................................................................................................................................7
Maintenance ...............................................................................................................................8
Main MV1000 Assembly Diagram..............................................................................................9
Main MV1000 Assembly Parts List ..........................................................................................10
Motor Housing Assembly Diagram..........................................................................................11
Motor Housing Assembly Parts List ........................................................................................12
Auto Filter Cleaner Assembly ..................................................................................................13
Notes.........................................................................................................................................14
California Proposition 65..........................................................................................................15
SMITH Standard Warranty .......................................................................................................16

Warnings
3
Warnings
The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclamation
point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When these
symbols appear in the body of this manual or on warning labels, refer back to these Warnings. Product-specific hazard
symbols and warnings not covered in this section may appear throughout the body of this manual where applicable.
WARNING
DUST HAZARD
Grinding concrete and other surfaces can create dust that contains hazardous substances.
To reduce the risk of serious injury:
• Control the dust to meet all applicable workplace regulations.
• Wear a properly fit-tested and government approved respirator suitable for the dust conditions when
emptying collection tank or performing maintenance.
• Do not use without dust bag and filters in place.
ELECTRIC SHOCK HAZARD
This equipment must be grounded. Improper grounding, setup, or usage of the system can cause elec-
tric shock.
• Turn off and disconnect power cord before servicing equipment.
• Connect only to grounded electrical outlets.
• Use only 3-wire extension cords.
• Ensure ground prongs are intact on power and extension cords.
• Do not expose to rain. Store indoors.
• Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the equipment. Keep
cord away from heat, sharp edges, or moving parts.
•Do not use on wet surfaces.
PERSONAL PROTECTIVE EQUIPMENT
You must wear appropriate protective equipment when operating, servicing, or when in the operating
area of the equipment to help protect you from serious injury, inhalation of dust or chemicals, and
hearing loss. This equipment includes but is not limited to:
• Protective eye wear.
• Hearing protection.
• Properly fit-tested and government approved respirator suitable for the dust conditions.

Warnings
4
GROUNDING
This product must be grounded. In the event of an electrical short circuit, grounding reduces the risk of
electric shock by providing an escape wire for the electric current. This product is equipped with a cord
having a grounding wire with an appropriate grounding plug. The plug must be plugged into an outlet
that is properly installed and grounded in accordance with all local codes and ordinances.
• Improper installation of the grounding plug is able to result in a risk of electric shock.
•When repair or replacement of the cord or plug is required, do not connect the grounding wire to
either flat blade terminal.
•The wire with insulation having an outer surface that is green with or without yellow stripes is the
grounding wire.
• Check with a qualified electrician or serviceman when the grounding instructions are not completely
understood, or when in doubt as to whether the product is properly grounded.
•Do not modify the plug provided; if it does not fit the outlet, have the proper outlet installed by a
qualified electrician.
• This product is for use on a nominal 120V or 230V circuit and has a grounding plug similar to the
plugs illustrated in the figure below.
• Only connect the product to an outlet having the same configuration as the plug.
•Do not use an adapter with this product.
Extension Cords:
• Use only a 3-wire extension cord that has a grounding plug and a grounding receptacle that
accepts the plug on the product.
•Make sure your extension cord is not damaged. If an extension cord is necessary, use 12 AWG
(2.5 mm2) minimum to carry the current that the product draws.
• An undersized cord results in a drop in line voltage and loss of power and overheating.
WARNING
120V US 230V

Warnings
5
EQUIPMENT MISUSE HAZARD
Misuse can cause death or serious injury.
• Do not operate the unit when fatigued or under the influence of drugs or alcohol.
• Do not leave the work area while equipment is energized. Turn off all equipment when equipment is
not in use.
• Check equipment daily. Repair or replace worn or damaged parts immediately with genuine
manufacturer’s replacement parts only.
• Do not alter or modify equipment.
• Use equipment only for its intended purpose. Call your distributor for information.
• Keep children and animals away from work area.
• Comply with all applicable safety regulations.
• Maintain a safe operating distance from other people in the work area.
ENTANGLEMENT HAZARD
Rotating parts can cause serious injury.
• Keep clear of moving parts.
• Do not operate equipment with protective guards or covers removed.
•Do not wear loose clothing, jewelery, or long hair while operating equipment.
FIRE AND EXPLOSION HAZARD
Flammable fumes in work area can ignite or explode. To help prevent fire and explosion:
• Do not use to pick up flammable or combustible liquids, such as gasoline, or use in areas where they
may be present.
WARNING

The MV1000S dust collector is a rugged, powerful
unit that is sure to meet your expectations for dust
control.
See technical data below:
Voltage 220 V / 60 Hz - Single phase
Power 4050 W (5.3 HP)
Air pressure 3000 mm Aq
Airow 330 c.f.m
Hose 2” (50 mm) Dia.
Weight 175lbs (80kg) (net)
Dimension 27x27x62 in (67x67x155 cm) (LxWxH)
Plastic dust bag 22x32 in (550x800 mm) (LDPE)
Noise 75 dB
TROUBLESHOOTING
PROBLEM
Possible Reason(s)/Solution(s)
MOTOR DOES NO START
No power, cable or switch defective
MOTOR RUNS BUT NO SUCTION
Hose not connected or blocked
MOTOR RUNS W/ POOR SUCTION
Hose damaged
Filter blocked
Top cover loose
DUST BLOWS FROM MOTOR
Filter loose or defective
ABNORMAL NOISE
Check motor(s)
Connect hoses.
If using a separator:
• Connect oneendofthe Short VacuumHose tothe
inlet of theMaxiVac. Connect the other end of the
short hosetothe outlet of the separator.
• Connect oneendof the LongVacuum Hose to the
inlet of the separator. Connect the other end of the
long hose to thevacuum hookup on the SMITH
machine.
If not using a separator:
• Connect oneendof the LongVacuum Hose to the
inlet of theMaxiVac. Connect the other end of the
long hose to the vacuumhookup on the machine.
NOTE: Use the Y-Connector to connect2 hoses to the
vacuumor separator, if desired.
SETUP
6

Operation
1. Ensure all LazerVac motor switches are turned to
“OFF”. Plug vacuum into grounded power source.
2. Turn Auto Filter Cleaner Power Switch to “ON”.
Ensure the sound of the Filter Cleaner Bar is heard
contacting the inside of the filter. If no sound is
heard, replace the Plastic Inserts on the cleaning
bar. See page 18.
3. After 10 seconds, turn on a Vacuum Motor Switch.
Turn on additional vacuum motors if more vacuum
power is needed.
4. LazerVac is now ready for dust collection from the
GrindLazer or other removal equipment.
5. Use the vacuum accessories shown in the section
titled Main Assembly Diagram (LazerVac), page
12 to pick up dust from the ground between grinding
passes.
Cyclone LP
1. When Vacuum Collection Bag has collected
approximately 45 lbs (20 kg) of dust, the bag should
be replaced.
2. Pull down on the continuous bag to expose 6 - 12”
(15 - 30 cm) of new, unused bag.
3. Use a cable tie to tie off the top of the bag. Fasten
another cable tie 2” (5 cm) cable tie above the first
cable tie.
4. Put on respirator. Cut the bag between the two
cable ties.
5. Dispose of the dust bag. Follow local ordinances
and regulations for disposal.
6. Pull down on the new bag attached to the vacuum
until the bottom of the bag rests on the bottomof the
vacuum cart. Ensure the bottom of the bag is tied off
firmly with the cable tie.
7

Maintenance
8
Maintenance
The following steps should be performed to maintain
proper operation and sustain the life of the MaxiVac.
Daily
• Prior to use, inspect all hoses for holes. Repair or
replace damaged hoses.
• To help maintain performance and dust control,
replace filters when:
- Vacuum filters have tears or are clogged.
- Airborne dust is visible when using the
MaxiVac.
Weekly
• Inspect Filter Ring Seal for damage. If damaged,
replace seal. Ensure seals are installed correctly
and properly sealed.
• Inspect Filter Cleaner Plastic Inserts for wear or
damage. Replace the inserts regularly to help
maintain performance and dust control.
Recycling and Disposal
End of Product Life
At the end of a product’s useful life, recycle it in a
responsible manner.
DUST AND SHOCK HAZARD
To reduce the risk of serious injury:
• Respirator must be worn during all maintenance.
• Follow local ordinances and regulations for
disposal of dust.
• Unplug vacuum from power source before
maintenance.

Parts
9
Parts
Main MV1000 Assembly Diagram

Parts
10
Main MV1000 Assembly Parts (MV1000)
Ref Part Number Description Qty
1 See page 9-11 Motor Housing Assembly 1
2 See page 13 Auto Filter Cleaner Assembly 1
3MV.1.891A Filter (includes item 4) 1
4 17X197 Main Body / Filter Seal Rubber Ring 2
5 MV.1.06 Main Body / Filter Housing 1
6 17X197 Rubber Seal 1
7 17X196 Metal Seal Ring 1
8 MV.1.019 Main Frame 1
8a 17X154 Velcro Belt for Dust Bag 1
8b MV.1.20 20”x32” Dust Bag 1
9* 17X156 Long Vacuum Hose, Standard, 2” (includes item 19) 1
10 MV.26 Vacuum Extension (set of 2) 1
11 MV.24 Vacuum Large Brush 1
12 MV.22 Vacuum Small Brush 1
13 MV.25 Vacuum Floor Nozzle 1
14 MV.27 Vacuum Elbow 1
15s
(not shown)
17X522 Warning Label (English, French, Spanish) 1
17X523 Warning Label (English, Chinese, Korean) 1
17X524 Warning Label (Icons) 1
16 MV.1.025 Dust Bag Holder 1
17 MV.3.20 Dust Bag (set of 20) 1
18 MV-Y Y-Connector (MaxiVac 330 only) 1
19 MV.23 2” Hose Connector 2
sReplacement warning, safety labels, tags, and cards are available at no cost.
* 2” Heavy Duty, High Temperature Hose available: P/N MV.HS.SD

Parts
11
Motor Housing Assembly Diagram (MV1000)

Parts
12
Motor Housing Assembly Parts List (MV1000)
Part Number Description Qty
1A.HN.25-20 Acorn Nut 6
2 17X169 Motor Housing Cover (includes IEC power cord) 1
31HN.25-20X1.0 Hex Spacer, Long (not shown, located inside item 2) 6
4MV.1.07 Set of Motor Rubber Rings and Plastic Net 3
6MV.1.06A Motor, 230V 3
7HN.25-20X.50 Hex Spacer, Short 6
10 MV.1.010 Motor Table 1
11 FLW.M6 Flat Washer 6
12 HX-CS.25-20X2FT Hex Head Screw Cap 6
20 17Y218 Power cord, IEC 1
21†17Y089 Cord Adapter, US, NEMA 1
22†17A242 Cord Adapter, Australia 1
23†15G961 Cord Adapter, Switzerland 1
24†15G960 Cord Adapter, Denmark 1
25†15G959 Cord Adapter, Italy 1
26†15G958 Cord Adapter, Europe, Schuko 1
27 (not
shown)
121249 Cord Retainer for Cord Adapters 1
† Cord Adapters are sold separately from MaxiVac 330 (25E237)

Parts
13
Auto Filter Cleaner Assembly (MV1000)
‡
Part Number Description Qty
1MV.1.13A Auto Filter Cleaner Assembly Motor Stand 1
2
MV.3.12B 120V Filter Cleaner Assembly Motor 1
MV.1.12A 230V Filter Cleaner Assembly Motor 1
3* MV.1.11-C Filter Cleaner Bar, Support (set of 2) 1
4† MV.1.11-D Filter Cleaner Plastic Insert 1
* MaxiVac 230 and 330 come with one replacement set of item 3
†MaxiVac 230 and 330 come with three replacements of item 4

Parts
14
Notes

California Proposition 65
15
California Proposition 65
CALIFORNIA RESIDENTS
WARNING: Cancer and reproductive harm – www.P65warnings.ca.gov.

SMITH Standard Warranty
SMITH warrants all equipment referenced in this document which is manufactured by SMITH and bearing its name to be free from defects in
material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty
published by SMITH, SMITH will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by
SMITH to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with SMITH’s written
recommendations.
This warranty does not cover, and SMITH shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty
installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of
non-SMITH component parts. Nor shall SMITH be liable for malfunction, damage or wear caused by the incompatibility of SMITH equipment with
structures, accessories, equipment or materials not supplied by SMITH, or the improper design, manufacture, installation, operation or
maintenance of structures, accessories, equipment or materials not supplied by SMITH.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized SMITH distributor for verification of
the claimed defect. If the claimed defect is verified, SMITH will repair or replace free of charge any defective parts. The equipment will be returned
to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will
be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED
TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
SMITH’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy
(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or
consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.
SMITH MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT
MANUFACTURED BY SMITH. These items sold, but not manufactured by SMITH (such as electric motors, switches, hose, etc.), are subject to
the warranty, if any, of their manufacturer. SMITH will provide purchaser with reasonable assistance in making any claim for breach of these
warranties.
In no event will SMITH be liable for indirect, incidental, special or consequential damages resulting from SMITH supplying equipment hereunder,
or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the
negligence of SMITH, or otherwise.
FOR SMITH CANADA CUSTOMERS
The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into,
given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la
rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite
de ou en rapport, directement ou indirectement, avec les procédures concernées.
SMITH Information
For the latest information about SMITH products, visit www.SMITH.com.
For patent information, see www.SMITH.com/patents.
TO PLACE AN ORDER, contact your SMITH distributor or call 1-800-690-2894 to identify the nearest distributor.
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
Original instructions. This manual contains English. MM 3A5576
SMITH Headquarters: Pompano Beach, FL
SMITH Surface-Prep Solutions • 2504 NW 19 ST • Pompano Beach, FL 33069 • USA
Copyright 2020, SMITH Surface-Prep Solutions. All rights reserved
www.smithmfg.com
Revision G January 2022