Snapper CP215518HV User manual

Parts Manual fo
r
Revision 1,
21" STEEL DECK WALK BEHIN
D
SERIES 18
COPYRIGHT
©
2005
McDonough, GA, 30253 U.S.A.
TP 400-5048-1-WB-N
8/3/2005 Manual No. 7006140
SNAPPER PRODUCTS, INC.
ALL RIGHTS RESERVED.
COMMERCIAL MOWER
S
MODEL
CP215518HV
CP216018KW
V
CRP216018KWV

Table Of Content
s
TP 400-5048-1-WB-N
Manual No. 700614021" STEEL DECK WALK BEHIND
SERIES 18 3
PAGE GROUP
4HANDLES & CONTROLS (Upper End)
8HANDLES & CONTROLS (Lower End)
10 CUTTING DECK, BLADE
12 FRONT WHEEL BRACKET, LATCHES
14 REAR WHEEL BRACKETS, LATCHES
16 FRONT AND REAR WHEELS
18 DRIVE SYSTEM SELF-PROPELLED
22 TRANSMISSION (DIFFERENTIAL)
24 SIDE CHUTE ADAPTER
26 ACCESSORY GRASS BAG
28 THROTTLE CONTROLS/ENGINE SPECS
30 DECALS
32 SNAPPERIZER ACCESSORY
34 ACCESSORY THATCHERIZER
36 RECYCLING KITS ACCESSORY

HANDLES & CONTROLS (Upper End)
TP 400-5048-1-WB-N
Manual No. 7006140 21" STEEL DECK WALK BEHIND
SERIES 18
4

HANDLES & CONTROLS (Upper End)
Footnotes:
TP 400-5048-1-WB-N
Manual No. 700614021" STEEL DECK WALK BEHIND
SERIES 18 5
Part No Descri
p
tionItem Qt
y
Note
1 7074411 1 HANDLE, Upper
2 7074156 1 HANDLE, Middle
3 7074418 1 BAIL, OPC Control
4 7034872 1 CLIP, Zone Control
5 7074141 1 CABLE, Zone Control (56-5/16” Long) CP216018KWV &
CRP216018KWV
-- 7029344 1 CABLE, Zone Control (49.98” Long) CP215518HV
6 7074473 1 HANDLE, Clutch
7 7028407 1 GRIP, International Symbol
8 7034604 1 CABLE, Clutch Control (41-1/4” Long)
9 7012121 1 COVER, Vinyl
-- 7075305 1 COVER, Grip CP215518HV
10 7012122 1 SPRING, Clutch- 21S
11 7074003 1 BRACKET, Shift
12 7074133 1 ROD, Speed Control (1/4-28 thread)
13 7091305 1 SCREW, 3/8-16 x 2” Hex Head Cap, GR 5
14 7031961 2 WASHER, 7/16” Flat
15 7028465 2 WASHER, Nylon
16 7091190 2 BOLT, 5/16-18 x 1-1/2” Curved Head
17 7091576 2 NUT, 1/4-20 Hex Was 91100
18 7023813 3 CLIP, Wiring Harness
19 7079577 2 SCREW, 1/4-20 x 1-1/2 Hex Head Cap GR5
20 7026219 1 CLAMP, 7/8” Double Cable
21 7090505 2 SCREW, 1/4-20 x 2” Hex Head Cap, GR 5
22 7090053 2 WASHER, 1/4” Internal Tooth Lock Was 91023
23 7074140 1 CONTROL PANEL (w/o Electrical Switch Hole)
24 7091200 4 SCREW, 1/4-20 x 1/2” Pan Head Self-Tap (Torx)
25 7014343 2 BUSHING, .27 x .35 x .4 Flange
26 7023792 1 PIN, 1/4 x 1-1/2”
27 7091020 1 PUSH-NUT, 1/4”
28 7023810 1 FOAM GRIP, 18.75” long
29 7090391 3 WASHER, 5/16” Internal Tooth Lock
30 7029366 1 DECAL, Commercial, WBM
31 7091511 2 NUT, 5/16-18 Hex, GR 5 Was 91069
32 7029782 1 DECAL, OPC Bail (International Symbol)
33 7028488 1 GUIDE, Rope (1/4-20 thread)
34 7028568 1 WASHER, Belleville
35 7091585 1 NUT, 3/8-16 Hex Center Lock

HANDLES & CONTROLS (Upper End)
TP 400-5048-1-WB-N
Manual No. 7006140 21" STEEL DECK WALK BEHIND
SERIES 18
6

HANDLES & CONTROLS (Upper End)
Footnotes:
TP 400-5048-1-WB-N
Manual No. 700614021" STEEL DECK WALK BEHIND
SERIES 18 7
Part No Descri
p
tionItem Qt
y
Note
36 7074113 1 LEVER, Shift
37 7075182 1 KNOB, Shift
38 7091167 1 SCREW, #8-32 x 1/2” Cross Recess Filister Head Machine
39 7091018 1 NUT, #8-32 Hex
40 7090188 3 WASHER, 3/8” Flat
41 7034162 1 COTTER PIN, 5/16 Self Lock
42 7024641 1 TIE, Wire, 1.29 long, black
43 7076978 2 NUT, 1/4-28 Hex Nyloc
44 7012080 2 CABLE-TIE, 7”
45 7078026 1 THROTTLE CONTROL, 50.81”, Honda CP215518HV
-- 7074138 1 THROTTLE CONTROL, 6.0 KWV CP216018KWV &
CRP216018KWV
46 7075308 1 THROTTLE KNOB

HANDLES & CONTROLS (Lower End)
TP 400-5048-1-WB-N
Manual No. 7006140 21" STEEL DECK WALK BEHIND
SERIES 18
8

HANDLES & CONTROLS (Lower End)
Footnotes:
TP 400-5048-1-WB-N
Manual No. 700614021" STEEL DECK WALK BEHIND
SERIES 18 9
Part No Descri
p
tionItem Qt
y
Note
1 7033985 1 HANDLE, Lower LH (Adjustable)
2 7033986 1 HANDLE, Lower RH (Adjustable)
3 7090799 2 BOLT, 5/16-18 x 5/8” Short Neck Carriage GR 5 Was 91026
4 7091601 2 NUT, 5/16-18 Hex Flange Lock GR 5 Was 91070
5 7046707 2 STRAP, Handle
6 7090095 4 NUT, 1/4-28 Hex, GR 5
7 7015753 2 BALL JOINT, 1/4-28
8 7090053 4 WASHER, 1/4” Internal Tooth Lock
9 7090595 5 BOLT, 5/16-18 x 3/4” Hex Flange Lock GR 5
10 7091601 10 NUT, 5/16-18 Hex Flange Lock, GR 5 Was 90585
11 7073822 1 BRACKET, Bell Crank
12 7013849 1 SPACER, .33 x .63 x .156
13 7073913 1 BELL CRANK
14 7091130 1 WASHER, .33 x .88 x .09 Flat
15 7091904 1 SCREW, 5/16-18 x 7/8” Hex Head Cap, GR 5
16 7091190 4 BOLT, 5/16-18 x 1-1/2” Curved Head
17 7091575 1 NUT, 5/16-18 Hex Center Lock Was 91067
18 7090238 1 SCREW, 5/16-24 x 1” Hex Head Cap GR5
19 7012114 1 BUSHING, Differential
20 7090895 1 NUT, 5/16-18 Tee
21 7032408 1 GUIDE, Lower V-Belt
22 7091606 1 NUT, 5/16-18 Hex, GR 5 Was 91074
29 7090391 4 WASHER, 5/16” Internal Tooth Lock
31 7091511 4 NUT, 5/16-18 Hex, GR 5 Was 91069

CUTTING DECK, BLADE
TP 400-5048-1-WB-N
Manual No. 7006140 21" STEEL DECK WALK BEHIND
SERIES 18
10