Snapper Series 19 EP216751BV User manual

Parts Manual fo
r
Revision IR,
21" STEEL DECK EUROPEA
N
SERIES 19
COPYRIGHT
©
2006
McDonough, GA, 30253 U.S.A.
TP 400-5198-IR-WB-N
6/12/2006 Manual No. 7006157
SNAPPER PRODUCTS, INC.
ALL RIGHTS RESERVED.
WALK BEHIND MOWERS
MODEL
EP217019BV
ERP2167519BV
ERP217019B
V

Table Of Content
s
TP 400-5198-IR-WB-N
Manual No. 700615721" STEEL DECK EUROPEAN
SERIES 19 3
PAGE GROUP
4HANDLES & CONTROLS
8CUTTING DECK, BLADES
10 WHEEL BRACKETS, LATCHES
12 WHEELS, FRONT & REAR
14 DRIVE SYSTEM SELF-PROPELLED
18 TRANSMISSION (DIFFERENTIAL)
20 THROTTLE CONTROLS/ENGINE SPECS
22 SIDE CHUTE ADAPTER
24 ACCESSORY GRASS BAG
26 DECALS
28 RECYCLING KITS ACCESSORY
30 SNAPPERIZER ACCESSORY
32 THATCHERIZER ASSEMBLY

HANDLES & CONTROLS
TP 400-5198-IR-WB-N
Manual No. 7006157 21" STEEL DECK EUROPEAN
SERIES 19
4

HANDLES & CONTROLS
Footnotes:
TP 400-5198-IR-WB-N
Manual No. 700615721" STEEL DECK EUROPEAN
SERIES 19 5
Part No Descri
p
tionItem Qt
y
Note
1 7074411 1 HANDLE, Upper
2 7074156 1 HANDLE, Middle
3 7033985 1 HANDLE, Lower LH (Adjustable)
4 7033986 1 HANDLE, Lower RH (Adjustable)
5 7074418 1 BAIL, OPC Control
6 7034872 1 CLIP, Zone Control
7 7034608 1 CABLE, Zone Control (52-63/64” Long)
8 7074473 1 HANDLE, Clutch
9 7028407 1 GRIP, International Symbol
10 7034604 1 CABLE, Clutch Control (41-1/4” Long)
11 7012121 1 COVER, Vinyl
12 7012122 1 SPRING, Clutch- 21S
13 7074003 1 BRACKET, Shift
14 7024641 2 TIE, Wire, 1.29 long, black
15 7073822 1 BRACKET, Bell Crank
16 7013849 1 SPACER, .33 x .63 x .156
17 7073913 1 BELL CRANK
18 7074140 1 CONTROL PANEL (w/o Electrical Switch Hole)
19 7091200 4 SCREW, 1/4-20 x 1/2” Pan Head Self-Tap (Torx)
20 7091130 2 WASHER, .33 x .88 x .09 Flat
21 7091904 1 SCREW, 5/16-18 x 7/8” Hex Head Cap, GR 5
22 7090895 1 TEENUT 5/16-18
23 7012114 1 BUSHING, Differential, .328 x .625 x .41
24 7090595 2 BOLT, 5/16-18 x 3/4” Hex Flange Lock GR 5
25 7090585 2 NUT, 5/16-18 Hex Flange Lock, GR 5 or 7091601
26 7091067 1 NUT, 5/16-18 Hex Center Lock
27 7074113 1 LEVER, Shift
28 7091606 1 NUT, 5/16-24 Hex Center Lock GR 5
29 7023813 1 CLIP, Wiring Harness
30 7091189 4 SCREW, 5/16-18 x 1-7/8” Curved Head GR 2 or 7091740
31 7035744 4 KNOB, 5/16-18 Wing (Black)
32 7079577 2 SCREW, 1/4-20 x 1-1/2 Hex Head Cap GR 5
33 7090053 5 WASHER, 1/4” Internal Tooth Lock
34 7091100 3 NUT, 1/4-20 Hex or 7091576
35 7090505 1 SCREW, 1/4-20 x 2” Hex Head Cap, GR 5
36 7014343 2 BUSHING, .27 x .35 x .4 Flange
37 7023792 1 PIN, 1/4 x 1-1/2”
Note* See also Throttle Control Page

HANDLES & CONTROLS
TP 400-5198-IR-WB-N
Manual No. 7006157 21" STEEL DECK EUROPEAN
SERIES 19
6

HANDLES & CONTROLS
Footnotes:
TP 400-5198-IR-WB-N
Manual No. 700615721" STEEL DECK EUROPEAN
SERIES 19 7
Part No Descri
p
tionItem Qt
y
Note
38 7091020 1 PUSH-NUT, 1/4”
39 7015753 2 BALL JOINT, 1/4-28
40 7090095 4 NUT, 1/4-28 Hex
41 7023810 1 FOAM GRIP, 18.75” long
42 7091305 1 SCREW, 3/8-16 x 2” Hex Head Cap, GR 5
43 7091585 1 NUT, 3/8-16 Hex Center Lock
44 7090391 4 WASHER, 5/16” Internal Tooth Lock
45 7031961 8 WASHER, 7/16” Flat
46 7028465 2 WASHER, Nylon
47 7074133 1 ROD, Speed Control (1/4-28 thread)
48 7028488 1 GUIDE, Rope (1/4-20 thread)
49 7076978 1 NUT, 1/4-28 Hex GR 5 or B
50 7012080 1 CABLE-TIE, 7”
51 7074460 1 *THROTTLE CONTROL, .48 x .61
52 7075308 1 THROTTLE KNOB
53 7075182 1 KNOB, Shift
54 7026219 1 CLAMP, 7/8” Double Cable
55 7091167 1 SCREW, #8-32 x 1/2” Cross Recess Filister Head Machine
56 7091018 1 NUT, #8-32 Hex
57 7091151 1 SCREW, 5/16-18 x 1-1/4” Hex Washer Head Self-Tap
58 7028568 1 WASHER, Belleville
59 7090238 1 SCREW, 5/16-24 x 1” Hex Head Cap GR 5
60 7090188 1 WASHER, 11/32” Flat
61 7034162 1 COTTER PIN, 5/16 Self Lock
62 7100183 1 DECAL, Easy Speed, Control Panel
63 7023153 1 CLAMP, Casing
64 7023154 1 SCREW,#10-32 x 5/8” Self-Tap
Note* See also Throttle Control Page

CUTTING DECK, BLADES
TP 400-5198-IR-WB-N
Manual No. 7006157 21" STEEL DECK EUROPEAN
SERIES 19
8

CUTTING DECK, BLADES
Footnotes:
TP 400-5198-IR-WB-N
Manual No. 700615721" STEEL DECK EUROPEAN
SERIES 19 9
Part No Descri
p
tionItem Qt
y
Note
1 7400026 1 WELDMENT, Deck, 21” Non-Adjust Air finish: red painted but w/o decals
1 7400027 1 WELDMENT, Deck, 21”, S.P., HV, Core Model finish: red painted but w/o decals
2 7091070 5 NUT, 5/16-18 Hex Flange Lock, GR 5
3 7090731 3 BOLT, 5/16-18 x 1/2”, Short Neck Carriage, GR 5
4 7046780 2 PLUG, Hole, Polyethylene
5 7090001 1 BOLT, 5/16-18 x 3/4” Short Neck Carriage GR 5 or 7091508
6 7011791 1 RETAINER, 5/16” Bolt
7 7090167 1 SCREW, 3/8-24 x 2” Hex Head Cap, GR 5
8 7012063 2 WASHER, Cone
9 7019795 1 BLADE, 21” Air Lift
10 7026407 1 BLADE, 21” Ninja (Quad Edge) used on ERP2167519BV &
ERP217019BV
11 7074568 1 COVER, Belt
12 7015780 1 PULLEY, Engine (25mm I. D. x 2-1/8” O.D.)
13 7092086 1 SCREW, 5/16-18 x 1/2” Hex Socket Head
14 7091214 1 KEY, Woodruff #HP-506 Hi-Pro Used on EP217019BV &
ERP217019BV
15 7015626 1 HUB, Blade Drive 25mm I.D.
16 7090324 3 SCREW, 3/8-16 x 1” Self-Tapping engine mount bolts
17 7090228 4 SCREW, 5/16-24 x 21/32” Oval Head Machine
18 7032558 2 AIR LIFT
19 7090391 4 WASHER, 5/16” Internal Tooth Lock
20 7090223 4 NUT, 5/16-24 Hex, GR 5
21 7041400 1 FENDER (Weldment), EP21S
22 7090539 6 SCREW, 1/4-20 x 1/2” Hex Flange Self-Tap
23 7073462 1 DECAL, Caution Symbols (International)
24 7090702 1 BOLT, 5/16-18 x 2-1/4” Hex Flange Lock
25 7013320 1 BUSHING, .388 x .625 x 1.62 Flanged matl: powdered metal
26 7031961 2 WASHER, 7/16” Flat
27 7033863 1 COVER, Belt- IP21S
28 7090534 1 SCREW, 5/16-18 x 1/2” Hex Head Cap, GR 5
29 7091076 1 WASHER, 5/16” Flat
1 *ENGINE, 6.75 Briggs Quantum Mod 125K02-0142-E1 Used on ERP2167519BV
1 *ENGINE, 7HP Briggs Intek Euro Mod 128602-0112-E1 Used on EP217019BV &
ERP217019BV

WHEEL BRACKETS, LATCHES
TP 400-5198-IR-WB-N
Manual No. 7006157 21" STEEL DECK EUROPEAN
SERIES 19
10