SODEX S25233 Dimensions

DETAILS
SODEX INTERNATIONAL
18 rue de l’avenir – Bât. 224
14650 CARPIQUET
Tel: + 33 (0) 2.31.53.78.70
Email: [email protected]
DESCRIPTION
Aluminium structure Ø90mm
Plastified
CONFORM
European norm
NF EN 1510
PRODUCT SHEET
TENNIS POSTS TO SEAL,Ø90,
OUTSIDE WINCH
PRODUCT REF S25233 PAIR
ASSEMBLY TIME
The time to make the assembly of the posts is estimated at 30min at 1 person (sealing not included).
MAINTENANCE
The equipement has to be regularly maintained by the owner. It is adviced to:
- Check every week that all the screws are correctly tightened
- Fix paint defects if the module has been damaged, using the adapted paint, specified by the manufacturer.
- Replace all damaged or missing parts with a spare part recommended by the manufacturer.
- Clean the product by using dishwasher soap, clean water, and soft cloth.
WARRANTY
One full year parts and labor guarantee. Every claim regarding condition of the delivered equipment has to be done
within the legal period of the reception of the material. The warranty will not apply to:
- all degradation during the transport.
- all degradation due to use differing from which was intended.
- all degradation due to poor maintenance.
- any defect claimed after the end of the legal period.
- any damaged due to a faulty installation and assembly of the module

2
NB: All the dimensions are given in millimeters.
PENETRATION OF THE POST IN THE SOCKET: 350 mm
400 500
500
500
350
Dedicated to single use court or multi-sports
IMPLANTATION & SEALING :
COURT FOR DOUBLE GAME (DOUBLE
ALLEY
Court axle
Location of the sockets
- Dig the holes for the sealing according to the
written dimensions.
- Make the sealings with PJ 45 concrete dosed
by 350kg. Then putt he sockets in position,
using the dimensions given in the drawing
above. Be sure that the top of the sockets are
at the same level than the surface.
- Let the concrete dry at least 72 hours.

3
ASSEMBLY
1– TAKE THE RACK OUT OF THE BODY
NECESSARY
ITEMS
NECESSARY TOOLS (NOT INCLUDED)
ELEMENTS FOURNIS
STEP 1 STEP 2
Rack
Star wheelStop
Aluminium body
Unscrew the screw M4x20,
then push the stop to the
top as above and take out
the rack of the body.
Rack
X1
Tightening
handle M6x20
X2
Washers 8
X1
Bolts M4
X2
Screws M8x25
Wrench 8mm Wrench 13mm
X1
Screws M4x20
X1
Crank

4
3– PUT THE RACK BACK IN THE BODY AND FIX THE STOPPING SCREW
NECESSARY
ITEMS
Screw M4x20 +
nut M4
X1
Nut M4
WINCH ASSEMBLY
2– FIX THE ALUMINIUM BODY ON THE POST
NECESSARY
ITEMS
Screws M8x25 +
washers M8
Joint bars M8
Note: Make the two joint bars slide
into the rail until their holes coincide
with the holes made on the rail, then
tighten the winch thanks to the pro-
vided screws.
X1
Screws M4x20
X2
Washers 8
X2
Screws M8x25
X2
Joint bars 25x18x10

5
WINCH ASSEMBLY
4– CRANK ASSEMBLY
NECESSARY
ITEMS
Tightening handle M6x20
5– POSITION THE CRANK AS HIGH AS POSSIBLE BEFORE TENSIONING THE
NET
NECESSARY
ITEMS
Crank
X1
Crank
X1
Tigntening
handke M6x20

6
ASSEMBLY
NECESSARY TOOLS (NOT INCLUDED)
ELEMENTS FOURNIS
X6
Round head
screws M6x15
X2
Inox screws
X4
Inox washers 10
X2
Inox locknuts M10
X2
Pulleys
Allen key 5mm
X2
Pulley supports
X1
Cap D6
X2
Alu bars
1 – ASSEMBLY OF THE HOOK PLATE ON THE POST WITHOUT WINCH (x1)
STEP 3
NECESSARY
ITEMS
325 mm
STEP 1 STEP 2
Joint bar 55x18x10
Plat avec crochet+
vis tête hexagonale M6x15
Before this operation, please remove the PVC caps on the top of
the posts. For the step 2, don’t tighten the screws too much. The
definitive tightening will be done at the step 3.
X1
Hook
X1
Joint bars
55 x18x10
X1
Cap D6
X2
Round head
screws M6x15
X1
Hook
X1
Joint bars
55x18x10
Cap D6
X2
Joint bars
34x18x10
X2
Inow screws
M8x25
X2
Inox washers 8
X8
Hook PVC
Wrench 17mm

7
ASSEMBLY
2 – ASSEMBLY OF THE PULLEY SUPPORTS (x2)
STEP 1 STEP 2
NECESSARY
ITEMS
During step 1, do not tighten the
screws too much. The definitive tight-
ening will be done at the step 2.
Once the pulleys are in position, put
back the PVC cap at the top of the
posts.
Joint bars
34x18x10 Pulley support +
Round M6x15
3 – ASSEMBLY OF THE PULLEYS (x2)
NECESSARY
ITEMS
Inox screws M10x30 +
inox washers 10 + inox
locknuts M10
Do the same operation on
the two posts.
X4
Round head
screws M6x15
X2
Pulley supports
X2
Joint bars
34x18x10
X2
Inox screws
M10x30
X4
Inox wahsers 10
X2
Inox locknuts M10
X2
Pulleys
During the assembly, the pulley
must be positioned as high as
possible, touching against the
PVC cap.
Do the same operation on
the two posts.

8
ASSEMBLY
4– ASSEMBLY OF THE HOOKS AND OF THE ALUMINIUM BARS
NECESSARY
ITEMS
X8
PVC hooks
Aluminium bars
X2
Aluminium bars
Do the same operation on
the two posts.

9
NOMENCLATURE
Package
N° Ref Index Designation Description Quantity Packing method Weight (kg) Dim. (mm)
A1 S25233 DPost with and without
winch 1 + 1 Plastic bubbles + cardboard 5 layers 81420x200x110
ACCESSORIES PUT IN CLEAR PVC BAG
Package
N° Designation Description Qty Note
A1 Pulley D30 2To be assembled on
the posts
A1
Screws BC M10x30
+ washers BC 10
+ locknuts BC
M10
2 + 4 + 2 To fix the pulleys on
the posts
A1 Caps D6 1To be put on the
hooks
A1 Alu bars D8 2 To be fixed on the
posts
A1 Treuil+Visserie 1To be assembled on
one of the posts
A1 Inox support pulley 2To be fastened onto
the post
A1 Round head
screws M6x15 +
joint bars 34x18x10 4 + 2 To fasten the pulley
supports onto the
posts
A1 Joint bars
25x18x10 2To fix the winch
A1 Inox screws M8x25
+ inox washers 8 2 + 2 To fix the winch
A1 PVC hooks 8To be assembled on
the posts
A1
Round head
screws M6x15 +
plate with hook +
joint bar 55x18x10
2 + 1 + 1 For fixation of the plate with hook on the
post without winch
A1 Allen key 5mm 1Tool to fix the pulley
PRE-ASSEMBLED ACCESSORIES
Package
N° Designation Description Qty Note
A1 PVC caps D90 2Put at the top of the
posts
A1 Tennis stickers 1Stuck on the post
VISA PACKING DEPARTMENT DATE :
PACKING LIST
SEALED POSTS, D90, OUTTER
WINCH
PRODUCT REF. S25233 Index D PAIR

10
NOMENCLATURE
Package
N° Ref Index Designation Description Quantity Packing method Weight (kg) Dim. (mm)
A1 S25595 F
Alu body
+Crank
+Star wheel
+Stop
1 + 1 +1 +1 A winch with its
screws is put in a
clear PVC bag 1.3 400x80x60
ACCESSORIES PUT IN A CLEAR PVC BAG
Package
N° Designation Description Qty Note
A1 Tightening handle
M6x20 1
A1 Crank
1
PRE-ASSEMBLED ACCESSORIES
Package
N° Designation Description Qty Note
A1 Rack 1
A1 Stop 1
A1 Star wheel 1
A1 Rivet ø5x12+ ball 2 + 1
A1 Circlips 1
A1 Screws BC M4x20
+ Bolt BC M4 1+1
VISA PACKING DEPARTMENT
DATE :
PACKING LIST
ALU WINCH
PRODUCT REF S25595 Index F UNIT