Solaire GODDESS Royal Collection T6000 S User manual

1
DO NOT USE EQUIPMENT BEFORE READING THIS MANUAL
This manual contains important warnings and instructions.
Please read these instructions carefully and keep for your reference.
©2012 Solaire Pty Ltd
Unit 5, 32 Essington Street, Grovedale, 3216 email: [email protected]
Ph: 1300 650 079 www.solaire.com.au
INSTRUCTION MANUAL
TANNING SYSTEM
(FOR PROFESSIONAL USE ONLY)
DO NOT USE EQUIPMENT BEFORE READING THIS MANUAL
1 YEAR WARRANTY
DO NOT USE EQUIPMENT BEFORE READING THIS MANUAL
This manual contains important warnings and instructions.
Please read these instructions carefully and keep for your reference.
Please ll out the warranty card at the back to obtain warranty.
©2015 Solaire Pty Ltd
Unit 5, 32 Essington Street, Grovedale, 3216, Australia.
email: [email protected]
Ph: 1300 650 079
International: [phone]
www.solaire.com.au
DO NOT USE EQUIPMENT BEFORE READING THIS MANUAL
This manual contains important warnings and instructions.
Please read these instructions carefully and keep for your reference.
©2012 Solaire Pty Ltd
Unit 5, 32 Essington Street, Grovedale, 3216 email: [email protected]
Ph: 1300 650 079 www.solaire.com.au
INSTRUCTION MANUAL
TANNING SYSTEM
(FOR PROFESSIONAL USE ONLY)
DO NOT USE EQUIPMENT BEFORE READING THIS MANUAL
®
®
(Suitable for up to 20 sprays per day)
The Goddess Royal Collection™ sound level is: 71db

2

3
Table of Contents
1. General Safety Information: ....................................................................................................................4
2. Set up and operate your GODDESS Royal Collection™Spray Tan System: .................................... 5
3. Prepare the T6000 Spray Gun .................................................................................................................6
4. Adjusting the T6000 Spray Gun ..............................................................................................................8
5. Spraying ....................................................................................................................................................9
6. Maintenance ............................................................................................................................................. 10
7. Troubleshooting .......................................................................................................................................12
The GODDESS Royal Collection™ By Solaire® is easy to use anywhere, whether it be
at home, in a client’s home or as a medium business start up.
The GODDESS Royal Collection™ By Solaire® is made in the US and demonstrates the highest
of standards in design and manufacture.
The GODDESS Royal Collection™ By Solaire® has an interchangeable case top, which opens to
provide space for the mist applicator and your collection of spray tan solutions, professional
accessories, makeup or anything else you require to be truly mobile.
The GODDESS Royal Collection™ By Solaire® comes in a selection of colours and
has the ability to attach your own logo plate. Easy to use, and highly cost effective since the
solution goes on the client, not in the air. Superbly designed and engineered with
the feedback from you, the spray tanner.
GODDESS Royal Collection™By Solaire® Instruction Manual
Congratulations on purchasing the GODDESS Royal Collection™ tanning system. This product has been specially
designed to provide the best application of professional spray tanning solutions.
Take a minute to read and understand how to operate your new GODDESS Royal Collection™ tanning system and you
will be able to provide the perfect tan with every application.
Your GODDESS Royal Collection™ is packaged with the following:
1. GODDESS Royal Collection™ unit.
2. 3m Flex Air Hose
3. T6000 Spray Gun
4. Instruction Manual (see website)
5. Warranty Card
®
®

4
1. General Safety Information
Read all instructions and safety precautions before operating the unit.
THIS INDICATES A CONDITION THAT WILL CAUSE SERIOUS INJURY OR LOSS OF LIFE IF THE WARNING IS
IGNORED.
THIS INDICATES A CONDITION THAT COULD CAUSE SERIOUS INJURY OR LOSS OF LIFE IF THE WARNING IS
IGNORED.
THIS INDICATES A CONDITION THAT MAY CAUSE MINOR INJURY AND/OR EQUIPMENT/PROPERTY DAMAGE.
GROUNDING INSTRUCTIONS
This product must be properly grounded. In the event of an electrical short circuit, grounding reduces the risk of electrical
shock by providing an alternate path for the electrical current.
This product is equipped with a cord that has a ground wire and an appropriate ground plug. Plug the unit into an outlet
that is properly installed and grounded in accordance with local codes and ordinances.
IMPROPER INSTALLATION OF THE GROUND PLUG CAN RESULT IN THE RISK OF
ELECTRICAL SHOCK. IF REPAIR OR REPLACEMENT OF THE PLUG OR CORD IS
NECESSARY, DO NOT CONNECT THE GROUND WIRE TO EITHER FLAT BLADE
TERMINAL. THE WIRE WITH GREEN INSULATION (WITH OR WITHOUT A YELLOW
STRIPE) IS THE GROUNDING WIRE.
1. For any question regarding proper installation of the ground plug, consult a qualied
(licensed or certied) electrician.
2. Do not modify the plug provided. If the plug does not t the outlet, have the proper
outlet installed by a qualied electrician.
3. This product is for use on a nominal 240-volt circuit and has a grounding plug that
looks like the plug in Figure 2. Make sure that the product is connected to an outlet
having the same conguration as the plug. No adapters should be used with this
product.
4. If an extension cord is required, use only a three wire extension cord that has the
same conguration as the unit cord, including the ground terminal. Make
sure that the extension cord is plugged into a properly grounded receptacle.
5. When using an extension cord, be sure it is in good condition and meets specications.
6. Ensure the GODDESS Royal Collection™ is tagged and tested every 12 months after initial purchase to comply with
Australian Electrical Safety standards.
3
1 General Safety Information:
Read all instructions and safety precautions before operating the unit.
THIS INDICATES A CONDITION THAT WILL CAUSE SERIOUS INJURY OR LOSS OF LIFE IF THE WARNING IS
IGNORED.
THIS INDICATES A CONDITION THAT COULD CAUSE SERIOUS INJURY OR LOSS OF LIFE IF THE WARNING IS
IGNORED.
THIS INDICATES A CONDITION THAT MAY CAUSE MINOR INJURY AND/OR
EQUIPMENT/PROPERTY DAMAGE.
• Risk of fire or explosion! Solvent and paint fumes can explode or ignite, causing severe
injury and property damage.
• Paints and solvents containing HALOGENATED HYDROCARBONS can react explosively
with aluminum. Always check the product’s label before using these materials in the unit.
• Hazardous vapors: Paint, solvents, insecticides and other materials may be harmful if
inhaled, causing severe nausea, fainting or poisoning.
• Make sure the room is well ventilated. Avoid all ignition sources, such as static electricity
sparks, open flames, hot objects, sparks from connecting and disconnecting power cords,
and working light switches.
• Follow the material and solvent manufacturers’ safety precautions and warnings. Do not
use liquids with flash points less than 100 degrees Fahrenheit (38 degrees Celsius).
• Static electricity can be produced by HVLP spraying. Make sure any electrically conductive
object being sprayed is grounded to prevent static sparking. The sprayer is grounded to
prevent static sparking. The spray grounded through the electrical cord. If an extension
cord is necessary, the cord must be a grounded with three wires made for the appropriate
voltage used.
• Use a respirator or mask whenever there is a chance that vapors may be inhaled. Read
all instructions with the mask to ensure that the mask will provide the necessary
protection against the inhalation of harmful vapors.
• Do not carry the turbine while spraying.
• Keep the turbine at the maximum distance from the spraying area.
4
1 General Safety Information cont’d.:
• Tipping the Spray Gun causes the Spray Gun to clog. Dried spray material also clogs the pressure delivery tube
and fittings. The Spray Gun does not function when clogging occurs.
• When not in use, be sure to disconnect the hose and place the Spray Gun into the holder in the turbine to avoid
tipping.
GROUNDING INSTRUCTIONS
This product must be properly grounded. In the event of an electrical short circuit, grounding reduces the risk of electrical
shock by providing an alternate path for the electrical current.
This product is equipped with a cord that has a ground wire and an appropriate ground plug. Plug the unit into an outlet
that is properly installed and grounded in accordance with local codes and ordinances.
IMPROPER INSTALLATION OF THE GROUND PLUG CAN RESULT IN THE RISK OF
ELECTRICAL SHOCK. IF REPAIR OR REPLACEMENT OF THE PLUG OR CORD IS
NECESSARY, DO NOT CONNECT THE GROUND WIRE TO EITHER FLAT BLADE TERMINAL.
THE WIRE WITH GREEN INSULATION (WITH OR WITHOUT A YELLOW STRIPE) IS THE
GROUNDING WIRE.
1. For any question regarding proper installation of the ground plug, consult a qualified
(licensed or certified) electrician.
2. Do not modify the plug provided. If the plug does not fit the outlet, have the proper
outlet installed by a qualified electrician.
3. This product is for use on a nominal 240-volt circuit and has a grounding plug that
looks like the plug in Figure 2. Make sure that the product is connected to an outlet
having the same configuration as the plug. No adapters should be used with this
product.
4. If an extension cord is required, use only a three wire extension cord that has the
same configuration as the unit cord, including the (round) ground terminal. Make
sure that the extension cord is plugged into a properly grounded receptacle.
5. When using an extension cord, be sure it is in good condition and heavy enough to
meet the specifications in the chart below. If an extension cord is needed the
following wire sizes must be used.
6. (See Chart 1) Figure 2
25’ cord……………………..…….10, 12, or 14 Gauge
50’ cord……………………….………..10 or 12 Gauge
100’ cord………………………………………10 Gauge
Chart 1 Extension Cord Requirements
4
1 General Safety Information cont’d.:
• Tipping the Spray Gun causes the Spray Gun to clog. Dried spray material also clogs the pressure delivery tube
and fittings. The Spray Gun does not function when clogging occurs.
• When not in use, be sure to disconnect the hose and place the Spray Gun into the holder in the turbine to avoid
tipping.
GROUNDING INSTRUCTIONS
This product must be properly grounded. In the event of an electrical short circuit, grounding reduces the risk of electrical
shock by providing an alternate path for the electrical current.
This product is equipped with a cord that has a ground wire and an appropriate ground plug. Plug the unit into an outlet
that is properly installed and grounded in accordance with local codes and ordinances.
IMPROPER INSTALLATION OF THE GROUND PLUG CAN RESULT IN THE RISK OF
ELECTRICAL SHOCK. IF REPAIR OR REPLACEMENT OF THE PLUG OR CORD IS
NECESSARY, DO NOT CONNECT THE GROUND WIRE TO EITHER FLAT BLADE TERMINAL.
THE WIRE WITH GREEN INSULATION (WITH OR WITHOUT A YELLOW STRIPE) IS THE
GROUNDING WIRE.
1. For any question regarding proper installation of the ground plug, consult a qualified
(licensed or certified) electrician.
2. Do not modify the plug provided. If the plug does not fit the outlet, have the proper
outlet installed by a qualified electrician.
3. This product is for use on a nominal 240-volt circuit and has a grounding plug that
looks like the plug in Figure 2. Make sure that the product is connected to an outlet
having the same configuration as the plug. No adapters should be used with this
product.
4. If an extension cord is required, use only a three wire extension cord that has the
same configuration as the unit cord, including the (round) ground terminal. Make
sure that the extension cord is plugged into a properly grounded receptacle.
5. When using an extension cord, be sure it is in good condition and heavy enough to
meet the specifications in the chart below. If an extension cord is needed the
following wire sizes must be used.
6. (See Chart 1) Figure 2
25’ cord……………………..…….10, 12, or 14 Gauge
50’ cord……………………….………..10 or 12 Gauge
100’ cord………………………………………10 Gauge
Chart 1 Extension Cord Requirements
4
1 General Safety Information cont’d.:
• Tipping the Spray Gun causes the Spray Gun to clog. Dried spray material also clogs the pressure delivery tube
and fittings. The Spray Gun does not function when clogging occurs.
• When not in use, be sure to disconnect the hose and place the Spray Gun into the holder in the turbine to avoid
tipping.
GROUNDING INSTRUCTIONS
This product must be properly grounded. In the event of an electrical short circuit, grounding reduces the risk of electrical
shock by providing an alternate path for the electrical current.
This product is equipped with a cord that has a ground wire and an appropriate ground plug. Plug the unit into an outlet
that is properly installed and grounded in accordance with local codes and ordinances.
IMPROPER INSTALLATION OF THE GROUND PLUG CAN RESULT IN THE RISK OF
ELECTRICAL SHOCK. IF REPAIR OR REPLACEMENT OF THE PLUG OR CORD IS
NECESSARY, DO NOT CONNECT THE GROUND WIRE TO EITHER FLAT BLADE TERMINAL.
THE WIRE WITH GREEN INSULATION (WITH OR WITHOUT A YELLOW STRIPE) IS THE
GROUNDING WIRE.
1. For any question regarding proper installation of the ground plug, consult a qualified
(licensed or certified) electrician.
2. Do not modify the plug provided. If the plug does not fit the outlet, have the proper
outlet installed by a qualified electrician.
3. This product is for use on a nominal 240-volt circuit and has a grounding plug that
looks like the plug in Figure 2. Make sure that the product is connected to an outlet
having the same configuration as the plug. No adapters should be used with this
product.
4. If an extension cord is required, use only a three wire extension cord that has the
same configuration as the unit cord, including the (round) ground terminal. Make
sure that the extension cord is plugged into a properly grounded receptacle.
5. When using an extension cord, be sure it is in good condition and heavy enough to
meet the specifications in the chart below. If an extension cord is needed the
following wire sizes must be used.
6. (See Chart 1) Figure 2
25’ cord……………………..…….10, 12, or 14 Gauge
50’ cord……………………….………..10 or 12 Gauge
100’ cord………………………………………10 Gauge
Chart 1 Extension Cord Requirements
4
1 General Safety Information cont’d.:
• Tipping the Spray Gun causes the Spray Gun to clog. Dried spray material also clogs the pressure delivery tube
and fittings. The Spray Gun does not function when clogging occurs.
• When not in use, be sure to disconnect the hose and place the Spray Gun into the holder in the turbine to avoid
tipping.
GROUNDING INSTRUCTIONS
This product must be properly grounded. In the event of an electrical short circuit, grounding reduces the risk of electrical
shock by providing an alternate path for the electrical current.
This product is equipped with a cord that has a ground wire and an appropriate ground plug. Plug the unit into an outlet
that is properly installed and grounded in accordance with local codes and ordinances.
IMPROPER INSTALLATION OF THE GROUND PLUG CAN RESULT IN THE RISK OF
ELECTRICAL SHOCK. IF REPAIR OR REPLACEMENT OF THE PLUG OR CORD IS
NECESSARY, DO NOT CONNECT THE GROUND WIRE TO EITHER FLAT BLADE TERMINAL.
THE WIRE WITH GREEN INSULATION (WITH OR WITHOUT A YELLOW STRIPE) IS THE
GROUNDING WIRE.
1. For any question regarding proper installation of the ground plug, consult a qualified
(licensed or certified) electrician.
2. Do not modify the plug provided. If the plug does not fit the outlet, have the proper
outlet installed by a qualified electrician.
3. This product is for use on a nominal 240-volt circuit and has a grounding plug that
looks like the plug in Figure 2. Make sure that the product is connected to an outlet
having the same configuration as the plug. No adapters should be used with this
product.
4. If an extension cord is required, use only a three wire extension cord that has the
same configuration as the unit cord, including the (round) ground terminal. Make
sure that the extension cord is plugged into a properly grounded receptacle.
5. When using an extension cord, be sure it is in good condition and heavy enough to
meet the specifications in the chart below. If an extension cord is needed the
following wire sizes must be used.
6. (See Chart 1) Figure 2
25’ cord……………………..…….10, 12, or 14 Gauge
50’ cord……………………….………..10 or 12 Gauge
100’ cord………………………………………10 Gauge
Chart 1 Extension Cord Requirements
4
1 General Safety Information cont’d.:
• Tipping the Spray Gun causes the Spray Gun to clog. Dried spray material also clogs the pressure delivery tube
and fittings. The Spray Gun does not function when clogging occurs.
• When not in use, be sure to disconnect the hose and place the Spray Gun into the holder in the turbine to avoid
tipping.
GROUNDING INSTRUCTIONS
This product must be properly grounded. In the event of an electrical short circuit, grounding reduces the risk of electrical
shock by providing an alternate path for the electrical current.
This product is equipped with a cord that has a ground wire and an appropriate ground plug. Plug the unit into an outlet
that is properly installed and grounded in accordance with local codes and ordinances.
IMPROPER INSTALLATION OF THE GROUND PLUG CAN RESULT IN THE RISK OF
ELECTRICAL SHOCK. IF REPAIR OR REPLACEMENT OF THE PLUG OR CORD IS
NECESSARY, DO NOT CONNECT THE GROUND WIRE TO EITHER FLAT BLADE TERMINAL.
THE WIRE WITH GREEN INSULATION (WITH OR WITHOUT A YELLOW STRIPE) IS THE
GROUNDING WIRE.
1. For any question regarding proper installation of the ground plug, consult a qualified
(licensed or certified) electrician.
2. Do not modify the plug provided. If the plug does not fit the outlet, have the proper
outlet installed by a qualified electrician.
3. This product is for use on a nominal 240-volt circuit and has a grounding plug that
looks like the plug in Figure 2. Make sure that the product is connected to an outlet
having the same configuration as the plug. No adapters should be used with this
product.
4. If an extension cord is required, use only a three wire extension cord that has the
same configuration as the unit cord, including the (round) ground terminal. Make
sure that the extension cord is plugged into a properly grounded receptacle.
5. When using an extension cord, be sure it is in good condition and heavy enough to
meet the specifications in the chart below. If an extension cord is needed the
following wire sizes must be used.
6. (See Chart 1) Figure 2
25’ cord……………………..…….10, 12, or 14 Gauge
50’ cord……………………….………..10 or 12 Gauge
100’ cord………………………………………10 Gauge
Chart 1 Extension Cord Requirements
4
1 General Safety Information cont’d.:
• Tipping the Spray Gun causes the Spray Gun to clog. Dried spray material also clogs the pressure delivery tube
and fittings. The Spray Gun does not function when clogging occurs.
• When not in use, be sure to disconnect the hose and place the Spray Gun into the holder in the turbine to avoid
tipping.
GROUNDING INSTRUCTIONS
This product must be properly grounded. In the event of an electrical short circuit, grounding reduces the risk of electrical
shock by providing an alternate path for the electrical current.
This product is equipped with a cord that has a ground wire and an appropriate ground plug. Plug the unit into an outlet
that is properly installed and grounded in accordance with local codes and ordinances.
IMPROPER INSTALLATION OF THE GROUND PLUG CAN RESULT IN THE RISK OF
ELECTRICAL SHOCK. IF REPAIR OR REPLACEMENT OF THE PLUG OR CORD IS
NECESSARY, DO NOT CONNECT THE GROUND WIRE TO EITHER FLAT BLADE TERMINAL.
THE WIRE WITH GREEN INSULATION (WITH OR WITHOUT A YELLOW STRIPE) IS THE
GROUNDING WIRE.
1. For any question regarding proper installation of the ground plug, consult a qualified
(licensed or certified) electrician.
2. Do not modify the plug provided. If the plug does not fit the outlet, have the proper
outlet installed by a qualified electrician.
3. This product is for use on a nominal 240-volt circuit and has a grounding plug that
looks like the plug in Figure 2. Make sure that the product is connected to an outlet
having the same configuration as the plug. No adapters should be used with this
product.
4. If an extension cord is required, use only a three wire extension cord that has the
same configuration as the unit cord, including the (round) ground terminal. Make
sure that the extension cord is plugged into a properly grounded receptacle.
5. When using an extension cord, be sure it is in good condition and heavy enough to
meet the specifications in the chart below. If an extension cord is needed the
following wire sizes must be used.
6. (See Chart 1) Figure 2
25’ cord……………………..…….10, 12, or 14 Gauge
50’ cord……………………….………..10 or 12 Gauge
100’ cord………………………………………10 Gauge
Chart 1 Extension Cord Requirements
®
®

5
2. Set up and operate your GODDESS Royal Collection™Tanning System
1. Plug the GODDESS Royal Collection™ tanning system unit into a proper electrical outlet. Make sure that the electric
current you are connecting to is the same as your unit. (240v). DO NOT attempt to connect the unit to the wrong
electric current as this will not only damage your unit but also void your warranty.
2. Next, locate the male end of the air hose and connect it to the female quick connect on the GODDESS Royal
Collection™ tanning system.
a. To insert the male connection pull back on the ring of the black coupler located on the GODDESS Royal
Collection™ tanning system and insert the male connector on the hose. Figure 6.
Fig. 6
b. Release the ring to allow the coupler to snap into place. The hose should now be connected to the unit
Figure 7.
Fig. 7
c. To remove the air hose, pull back on the ring of the black coupler and remove
If you have just nished spraying, the connector may be hot. Allow the GODDESS Royal Collection™unit to cool
down for about 10 minutes before disconnecting the air hose from the GODDESS Royal Collection™unit. Use
Caution!
5
2 Set up and operate your PRINCESS Tanning System:
1. Plug the PRINCESS tanning system unit into a proper electrical outlet. Make sure that the electric current
you are connecting to is the same as your unit. (110v or 220v). DO NOT attempt to connect the unit to the wrong
electric current as this will not only damage your unit but also void your warranty.
2. Next, locate the male end of the air hose and connect it to the female quick connect on the PRINCESS
tanning system.
a. To insert the coupler pull back on the ring of the black coupler located on the PRINCESS tanning
system and connect it to the male connector on the hose. Figure 6.
Fig. 6
b. Release the ring to allow the coupler to snap into place. The hose should now be connected to the
unit Figure 7.
Fig. 7
c. To remove the air hose, pull back on the ring of the black coupler and remove
If you have just finished spraying, the connector may be hot. Allow the PRINCESS unit to cool down
or about 10 minutes before disconnecting the air hose from the turbo unit. Use Caution!
®
®

6
3 Prepare the T6000 Spray Gun:
1. The Mist Applicator Diagram
8
®
®

7
7
3 Prepare the T6050 Spray Gun cont’d.:
1. Follow the diagram to prepare the Spray Gun
a. Unscrew the plastic cup from the Spray Gun. Pour tanning solution into the cup. Do not fill more than ¾ full.
b. Carefully screw the cup back onto the main body of the Spray Gun. Screw the cup on firmly but DO NOT
over tighten. Over tightening will cause the cup to “pop” and damage the threads. Leakage can
then occur requiring replacement of the cup.
c. Locate the air cap (#2) on the T6050 diagram. Slightly turn the air cap ring (#1) anti or counter clockwise
to loosen the air cap. Notice that you can now rotate the air cap freely.
d. Look at Mist Applicator Patterns diagram below. Note the position of the air cap and the direction of the
spray pattern. Pattern 1 is for spraying across from side to side. Pattern 2 is for spraying up and down.
Pattern 3 will produce a spot or circle. Patterns 1 and 2 are the most common positions for applying
tanning solutions.
e. Turn the air cap (#2) to the position you want. Turn the air cap ring (#1) clockwise to lock the air cap in
place.
SPRAY GUN PATTERNS
1. Misting across from side to side
2. Misting up and down.
3. Misting in a spot or circle
1. Next, position the Turbo Unit as far away as practical and possible from the area where you will spray.
2. Attach the remaining end of the hose to the T6050 Spray Gun as follows:
a. Locate the coupler at the rear top of the T6050 Spray Gun. See T6050 diagram.
b. Pull back on the collar of the black connector on the air hose.
c. Push the connector over the coupler and release. Figure 7.
d. Your Spray Gun should now be firmly attached to the air hose.
7
3 Prepare the T6050 Spray Gun cont’d.:
1. Follow the diagram to prepare the Spray Gun
a. Unscrew the plastic cup from the Spray Gun. Pour tanning solution into the cup. Do not fill more than ¾ full.
b. Carefully screw the cup back onto the main body of the Spray Gun. Screw the cup on firmly but DO NOT
over tighten. Over tightening will cause the cup to “pop” and damage the threads. Leakage can
then occur requiring replacement of the cup.
c. Locate the air cap (#2) on the T6050 diagram. Slightly turn the air cap ring (#1) anti or counter clockwise
to loosen the air cap. Notice that you can now rotate the air cap freely.
d. Look at Mist Applicator Patterns diagram below. Note the position of the air cap and the direction of the
spray pattern. Pattern 1 is for spraying across from side to side. Pattern 2 is for spraying up and down.
Pattern 3 will produce a spot or circle. Patterns 1 and 2 are the most common positions for applying
tanning solutions.
e. Turn the air cap (#2) to the position you want. Turn the air cap ring (#1) clockwise to lock the air cap in
place.
SPRAY GUN PATTERNS
1. Misting across from side to side
2. Misting up and down.
3. Misting in a spot or circle
1. Next, position the Turbo Unit as far away as practical and possible from the area where you will spray.
2. Attach the remaining end of the hose to the T6050 Spray Gun as follows:
a. Locate the coupler at the rear top of the T6050 Spray Gun. See T6050 diagram.
b. Pull back on the collar of the black connector on the air hose.
c. Push the connector over the coupler and release. Figure 7.
d. Your Spray Gun should now be firmly attached to the air hose.
3. Prepare the T6000 Spray Gun cont’d
1. Follow the diagram to prepare the Spray Gun
a. Unscrew the plastic cup from the T6000 Spray Gun. Pour tanning solution into the cup. Do not ll more than ¾ full.
b. Carefully screw the cup back onto the main body of the T6000 Spray Gun. Screw the cup on rmly but DO NOT
over tighten. Over tightening will cause the cup to “pop” and damage the threads. Leakage can
then occur requiring replacement of the cup.
c. Locate the air cap (#2) on the T6000 diagram. With the gun facing towards you, slightly turn the air cap ring (#1) anti
clockwise to loosen the air cap. Notice that you can now rotate the air cap freely.
d. Look at Mist Applicator Patterns diagram below. Note the position of the air cap and the direction of the
spray pattern. Pattern 1 is for spraying across from side to side. Pattern 2 is for spraying up and down. Pattern 3
will produce a spot or circle. Patterns 1 and 2 are the most common positions for applying tanning solutions.
e. Turn the air cap (#2) to the position you want. Again with the gun facing towards you, turn the air cap ring (#1)
clockwise to lock the air cap in place.
2. Next, position the GODDESS Royal Collection™ unit as far away as practical and possible from the area where you will
be spraying.
3. Attach the remaining end of the hose to the T6000 Spray Gun as follows:
a. Locate the male connection at the rear top of the T6000 Spray Gun. See gure 8.
b. Pull back on the coupler of the black connector on the air hose.
Fig 8
c. Insert the male connector in the coupler and release.
d. Your T6000 Spray Gun should now be rmly attached to the air hose.
5
2 Set up and operate your PRINCESS Tanning System:
1. Plug the PRINCESS tanning system unit into a proper electrical outlet. Make sure that the electric current
you are connecting to is the same as your unit. (110v or 220v). DO NOT attempt to connect the unit to the wrong
electric current as this will not only damage your unit but also void your warranty.
2. Next, locate the male end of the air hose and connect it to the female quick connect on the PRINCESS
tanning system.
a. To insert the coupler pull back on the ring of the black coupler located on the PRINCESS tanning
system and connect it to the male connector on the hose. Figure 6.
Fig. 6
b. Release the ring to allow the coupler to snap into place. The hose should now be connected to the
unit Figure 7.
Fig. 7
c. To remove the air hose, pull back on the ring of the black coupler and remove
If you have just finished spraying, the connector may be hot. Allow the PRINCESS unit to cool down
or about 10 minutes before disconnecting the air hose from the turbo unit. Use Caution!
®
®

8
4. Adjusting the Spray Gun
1. Locate the Solution Flow Screw (#10) on the T6000 diagram.
2. Face the front of the T6000 gun away from you and turn the Solution Flow Screw clockwise. This reduces and will
eventually stop the ow of solution. DO NOT over-tighten the screw as this will cause damage to the end of the needle.
Once the trigger cannot be pulled back there is no point in tightening the screw down more, this will only damage the
end of the needle.
3. Turning the Solution Flow Screw anti clockwise will increase the ow of solution and turning the solution ow screw
clockwise will decrease the ow of solution.
4. In general, 1 ½ - 2 full turns from the fully closed position will provide a good solution ow. You may nd that you want
more or less solution. You can adjust the Solution Flow Screw to your desired setting. NOTE: Opening the Solution
Flow Screw more than 3 turns will not increase the solution ow and will in fact decrease the efciency of your T6000
Spray Gun.
5. In general, hold the T6000 Spray Gun 20-30cm from the person being sprayed. Moving the T6000 Spray Gun back
will increase the size of the mist pattern. Moving the T6000 Spray Gun closer will decrease the size of the mist pattern.
The further away you hold the T6000 Spray Gun, the more you will need to increase the solution ow thus causing
abnormal amounts of airborne solution (overspray).
6. Holding the T6000 Spray Gun closer to the person being sprayed along with a minimum ow of solution will provide the
best results, no streaks or running solution and virtually no mist in the spray area.
7. Be sure to move the T6000 Spray Gun at a slow, steady speed keeping the distance of the Spray Gun the same
throughout the application. This will ensure perfect results. It is actually very easy. Practice, Practice, Practice.
8. It is best to hold the T6000 Spray Gun in a vertical position when spraying. If you want to change the direction of the
mist pattern, rotate the position of the air cap rather than turning the T6000 Spray Gun on its side. Refer to the spray
gun pattern diagram on page 7.
9. Always hold or store the T6000 Spray Gun in a vertical position. It is a good habit to use, when you are not spraying.
10. Do not over-tighten the solution ow screw (#10) as this will damage the end of the needle point. Tighten the screw
until the needle cannot be pulled back. Once this point is reached there is no point in turning the solution slow screw
anymore as this will only cause damage to the needle point.
5
2 Set up and operate your PRINCESS Tanning System:
1. Plug the PRINCESS tanning system unit into a proper electrical outlet. Make sure that the electric current
you are connecting to is the same as your unit. (110v or 220v). DO NOT attempt to connect the unit to the wrong
electric current as this will not only damage your unit but also void your warranty.
2. Next, locate the male end of the air hose and connect it to the female quick connect on the PRINCESS
tanning system.
a. To insert the coupler pull back on the ring of the black coupler located on the PRINCESS tanning
system and connect it to the male connector on the hose. Figure 6.
Fig. 6
b. Release the ring to allow the coupler to snap into place. The hose should now be connected to the
unit Figure 7.
Fig. 7
c. To remove the air hose, pull back on the ring of the black coupler and remove
If you have just finished spraying, the connector may be hot. Allow the PRINCESS unit to cool down
or about 10 minutes before disconnecting the air hose from the turbo unit. Use Caution!
®
®

9
9
5 Spraying/Misting
a. You are now ready to begin misting.
b. The ON/OFF Switch is located under the carry handle of the Turbo Unit. Turn it on. You will hear a
sound similar to a vacuum cleaner. You may also notice that air is now blowing out of the front of the
Spray Gun. This is correct. Air will continually flow from the air cap of the Spray Gun as long as the
Turbo Unit is running and the air hose is connected.
c. Open the Solution Flow Screw as described in item 4.
d. Set the mist pattern you wish to use by adjusting the air cap to the desired position. Refer to Mist
Pattern Diagram.
e. Direct the Spray Gun to the area of the body that you want to start spraying.
f. Pull back on the trigger (#13) and move the Spray Gun as noted in the diagram below. Do not wave the
Spray Gun back and forth in front of your client by bending your wrist. Rather, keep your wrist straight
and move your entire arm. Movement should be steady, even and deliberate, keeping your distance the
same at all times.
PROPER MISTING TECHNIQUE
5. Spraying
You should now be ready to spray your client. Good quality results with your GODDESS Royal Collection™ spray tanning
system are a combination of careful preparation of your client, a proper spraying environment, a basic knowledge of the
solution you will be using and how these solutions work with your GODDESS Royal Collection™ spray tanning system.
1. You are now ready to begin spraying.
2. The ON/OFF Switch is located at the side of the GODDESS Royal Collection™ Unit. Turn it on. You will hear a sound
similar to a vacuum cleaner. You may also notice that air is now blowing out of the front of the T6000 Spray Gun. This is
correct. Air will continually ow from the air cap of the T6000 Spray Gun as long as the GODDESS Royal Collection™
Unit is running and the air hose is connected.
3. Open the Solution Flow Screw as described in item 4.
4. Set the mist pattern you wish to use by adjusting the air cap to the desired position. Refer to the spray gun pattern
diagram on page 7.
5. Direct the T6000 Spray Gun to the area of the body that you want to start spraying.
6. Pull back on the trigger (#13) and move the T6000 Spray Gun as noted in the diagram below. Do not wave the Spray
Gun back and forth in front of your client by bending your wrist. Rather, keep your wrist straight and move your entire
arm. Movement should be steady, even and deliberate, keeping your distance the same at all times.
20-30cm
®
®

10
6. Maintenance
1. GODDESS Royal Collection™Unit.
a. There is minimal maintenance to perform on the GODDESS Royal Collection™ unit. Make sure you keep the motor
unit as far away from your spraying area as possible.
b. Every night wipe over GODDESS Royal Collection™ unit with a damp cloth.
Please Note: Ensure no excess water is used as this will short circuit the unit.
c. Please see maintenance cleaning video at: http://www.solaire.com.au/Main.asp?_=Sunless Education
2. Air Filter.
a. Remove the air lter on the side of the unit and wash at the end of every week.
3. Air Hose.
a. Wipe the air hose daily with a damp cloth and store in a clean dry place.
4. T6000 Spray Gun - Daily Clean.
a. It is important to clean your T6000 Spray Gun daily.
b. At the end of the day or when the equipment will not be used any more, disconnect the T6000 Spray Gun from the
air hose.
c. Carefully unscrew the cup. If there is remaining solution, either close the cup with a lid, or pour the remaining
solution into a proper storage container.
d. Rinse the cup under warm running water until clean.
e. Turn the gun upside down and allow warm running water to run into the plastic tube, pull back the trigger and allow
the water to ow out of the nozzle. Continue until clear.
f. Fill the cup about ¼ full with AIRBRUSH CLEANER. Reconnect the T6000 Spray Gun to Air Hose. Turn on
the GODDESS Royal Collection™ Unit. Direct the T6000 Spray Gun to a safe area and spray the AIRBRUSH
CLEANER through the T6000 Spray Gun until the cup is empty and until the Spray becomes CLEAR.
g. Turn off the GODDESS Royal Collection™ Unit. Disconnect the T6000 Spray Gun. Unscrew the cup.
h. Start to dismantle your T6000 Spray Gun.
i. Unscrew and remove the Air Cap Ring (#1, Diagram on page 6). Rinse the threads under warm running water. Wipe,
the threads and dry. Add a small amount of Spray lube to the threads.
j. Remove the Air Cap (#2, Diagram on page 6). Rinse under warm water. Wipe clean, Dip into AIRBRUSH CLEANER
and dry.
k. Remove the plastic air plate (#5, Diagram on page 6) Rinse under warm water. Wipe clean.
l. Reinstall the three pieces you just removed by reversing the removal procedure. Your T6000 Spray Gun should be
ready for the next use.
m.Please see Spray Gun maintenance cleaning video at: http://www.solaire.com.au/Main.asp?_=Sunless Education
®
®

11
6. Maintenance Cont’d
5. T6000 Spray Gun - Weekly Clean.
Perform the Daily procedure then continue:
a. The Solution needle (#8, Diagram on page 6) To remove: Face the front of the gun away from you, turn the Solution
ow screw anti clockwise until it comes out of the Spray Gun. Be careful when removing the solution ow Screw as
there is a small spring (#9, Diagram on page 6) around the needle. Do not loose it. This is important to the operation
of the T6000 Spray Gun. Set the spring aside and pull the trigger all the way back until you can grab the needle with
your nger tips and pull it out from the back of the T6000 Spray Gun. Once removed, rinse under the warm running
water, dip into AIRBRUSH CLEANER and dry. Add gun lubrication to the needle. Simply rub a small amount of
Spray Gun lube around the needle shaft and spring. Later to reinstall repeat these steps in reverse.
b. The solution nozzle ( #3, Diagram on page 6) can be removed for additional cleaning if necessary, the needle must
rst be removed to do this procedure. With an adjustable wrench or spanner, place the tip of your adjustable wrench
or spanner on the two at areas of the nozzle (whilst the gun is facing you) and twist anti clockwise. Be careful.
There is a solution nozzle gasket (#4, Diagram on page 6) around the threads of the solution nozzle. Be sure to
reinstall or leakage will occur. Rinse under warm running water, take a cotton bud dip it into gun cleaner and clean
inside the threads. DO NOT USE ANYTHING METAL as it will scratch the threads or nozzle and this will cause
leaking. To reinstall repeat these steps in reverse.
c. Please see Spray Gun maintenance cleaning video at: http://www.solaire.com.au/Main.asp?_=Sunless Education
HVLP Gun/Airbrush Cleaner:
Specially formulated to breakdown and remove spray tanning ingredients and residue from Airbrush/HVLP tips & nozzles.
When using spray tan in your T6000 spray gun it can leave a build-up of residue that, overtime,
can clog your T6000 spray gun tip and interfere with the effectiveness of your spray pattern.
Solaire’s Airbrush Cleaner is specically developed to breakdown the residue left in your airbrush
tip or spray gun nozzle.
Spray Gun Lube
Spray Tan Gun Cleaner
Available through our Ofce – please call us!
*Excluded any parts that may be required to be replaced.
®
®

12
®
®
5. Troubleshooting
Q. GODDESS Royal Collection™ unit turned ON. Air blows out of T6000 Spray Gun?
• This is correct. Air blows constantly when GODDESS Royal Collection™ unit is ON.
Q. GODDESS Royal Collection™ unit turned ON. Unit does not operate or blow air?
• Check that the unit is plugged in to proper electric source. Be sure there is power at the electric source. If there is no
problem with electric supply, call for technical support.
Q. GODDESS Royal Collection™ unit is turned ON the trigger is pulled back on T6000 Spray Gun but no solution comes out?
• Check that the cup is screwed rmly to T6000 Spray Gun.
• Check that there is no solution bubbling or leaking around the cup.
• Turn GODDESS Royal Collection™ unit OFF. Unscrew cup. Be sure that Solution Tube and Disc (#14, Diagram
on page 6) is connected and has not come loose.
• Turn GODDESS Royal Collection™ unit OFF. Remove air cap ring (#1, Diagram on page 6) remove air cap (#2, Diagram
on page 6) remove air plate (#5, Diagram on page 6) remove the needle (#8, Diagram on page 6). Remove Solution nozzle
(#3, Diagram on page 6) with an adjustable wrench or spanner. There is a Solution nozzle gasket (#4, Diagram on page 6)
on the Solution nozzle. Do not lose it. Rinse Solution Nozzle under running water and check for dried solution that may have
blocked the hole. Reinstall Solution Nozzle Gasket. Reinstall Solution Nozzle, solution needle, air plate, air cap and air cap
ring. Try spraying again. If you still have a problem call for technical support.
Q. Solution leaks in front of trigger?
• With an adjustable wrench or spanner tighten Solution Needle Packing Screw (#7, Diagram on page 6). Do not
over tighten. This can cause Solution needle to stick and not spring back. Try spraying again. If leaking continues the
Solution Needle Packing needs to be replaced. (Rare). Remove solution needle (#8, Diagram on page 6), then remove
Solution Needle Packing Screw (#7, Diagram on page 6). Dry out the Solution Needle Packing’s (4) (#6, Diagram on page
6). Replace. Reinstall Solution Needle Packing Screw and solution needle. Tighten all the way, and then back off slightly.
(1/8 turn) Test the T6000 spray gun for leakage. If you still have a problem call for technical support.
Q. When GODDESS Royal Collection™ unit is ON, Solution continues to spray from the T6000 Spray Gun without trigger being
pulled?
• Immediately turn GODDESS Royal Collection™ unit OFF.
• Disconnect T6000 spray gun from air hose.
• Slightly adjust (loosen) Solution Needle Packing Screw (#7, Diagram on page 6). Test to see if problem is resolved.
• Check to see that Needle Spring is installed. (#9, Diagram on page 6). Remove Solution Flow Screw (#10, Diagram on page
6). Look for Needle Spring around the back of the Solution Needle. If lost, call for replacement.
• Check Solution nozzle. Remove and clean following the spray gun weekly clean directions on page 11.
Q. Solution leaks around the top of the cup.
• Make sure there is a gasket (#15, diagram on page 6)
• Make sure the cup is screwed rmly to the body of the T6000 Spray Gun.
• Make sure the threads around the cup are clean and the threads inside the cup top assembly are clean.
• Replace the cup top gasket. Pry out old gasket. Install new gasket. Test T6000 spray gun.

13
RECORD OF GODDESS ROYAL Collection™ USE
MODEL SERIAL# DATE PURCHASED
DATE HOURS OF USE TOTAL HOURS
®
®

14
RECORD OF GODDESS ROYAL Collection™ MAINTENANCE
DATE MAINTENANCE PERFORMED
®
®

Solaire Warranty Card
Solaire Pty ltd
Name: Salon or Business Name: Address: Telephone Number: Mobile: Email address: Date of Purchase: Purchased from: Proof of Receipt with matching serial number is copied and attached? Ye s No Model: Serial Number: I have read and understood the terms and conditions in the Solaire Warranty Card and I have completed the necessary requirements. Purchaser’s Acknowledgement Signature: Date: / / A warranty is provided with this piece of equipment provided it is used in conjunction with manufactures instructions and THE WARRANTY CARD IS RETURNED within 14 days of receipt of purchase AND prior to use the purchaser acknowledges reading and fully understanding the Manufactures Instruction Manual. You must complete your spray tan gun maintenance and equipment care training module. If you fail to complete all three of the above YOU VOID your warranty. e most common cause of failure of any spray tan equipment is lack of cleaning, so take the time to make sure you look aer your investment. Please ensure you read the instructions carefully and complete the spray tan gun maintenance and equipment care training module at www.solaire.com.au. You will need to register on the site prior to completing your training. e website is also full of a whole range of products and education to help you as the spray tan specialist ensure you deliver the most professional customer service and an award winning Solaire spray tan. •Complete your contact details. Attach a copy of the original receipt showing the serial number. Email to: [e-mail]. •Read the Manufactures Instruction Manual. •Register at www.solaire.com.au and complete the spray tan gun maintenance and equipment care training module. is is found in the education tab on the le hand side of
the home page. Click on sunless education and watch the video.

Solaire will extend a warranty on equipment as provided by the Manufactures Instruction Manual of the goods. Solaire Pty Ltd warrants that products assembled by Solaire Pty Ltd shall be free from defects as it relates to Solaire Pty Ltd workmanship for a period as outlined in the Manufactures Instruction Manual for each respective piece of equipment from the date of purchase from Solaire Pty Ltd or its distributors or agents to the buyer. If during the warranty period, the goods should prove defective as determined by Solaire Pty Ltd or its authorized repairer, then the Solaire can, at their discretion, repair or replace the goods. In no event shall Solaire Pty Ltd, manufacturer of goods, their subsidiaries and aliated companies, be liable for special, incidental, or consequential damages, including loss of prots, whether or not caused by or resulting from negligence of seller. In addition, this warranty shall not apply to any goods or portions thereof which have been subjected to abuse, misuse and improper installation, maintenance or operation, electrical failure or abnormal conditions, and to goods which have been tampered with, altered, modied, repaired or reworked by anyone not approved by Solaire Pty Ltd. Solaire Pty Ltd warranty herein is in lieu of and excludes all other warranties of seller and the distributor of the goods and their subsidiaries and aliated companies, whether expressly implied, statutory or otherwise created under applicable law including, but not limited to, the warranty of merchantability and the warranty of tness for particular purpose or use. is Warranty does NOT include: misuse, damage, neglect, alterations, disassembled equipment or modications, lack of maintenance, cleaning, water damage to electrical parts and INCORRECT VOLTAGE CONNECTION. Warranty Procedure: 1. Email: [e-mail] to request a WARRANTY Claim Form. Fill in the WARRANTY claim form and email it to:
[e-mail]. Try to include as much detail as possible about the problem.
2. If at all possible we try to help you solve the problem and therefore you may be contacted regarding your claim either via phone or email. If we
are unable to solve the issue the equipment will need to be assessed and it will need to go to one of our Authorised repairers - we will issue you a claim number.
3. Once you have your claim number insert the number on Warranty Claim Form. 4. Ensure equipment is clean, dry and securely wrapped to prevent any leaking of uid and well-padded and packaged to prevent damage to the
equipment during shipping.
5. Send the form with the goods to the address on the WARRANTY CLAIM FORM. 6. Send a copy of the receipt from the original purchaser showing serial number, place of purchase, date of purchase. 7. You will be required to pre - pay all shipping charges. 8. Our Authorized repairer will attend to you claim promptly and contact you to discuss aer they have assessed the claim.