Solem LR-IS-FL User manual

THE CONNECTED IRRIGATION EXPERT
LR-IS-FL
QUICK
INSTALLATION
GUIDE

2
PRESENTATION
DOWNLOADING
1. On your smartphone and/or tablet, go to «App Store» ou «Google Play».
2. Search «MySOLEM» in the search bar.
Step 1
3. Download MySOLEM applicaon.
MySOLEM
GET INSTALL
4. Once installed, acvate the Bluetooth®on your smartphone and/ or tablet.
The LR-IS-FL is a Bluetooth®/ LoRaTM mains water mer, remotely controllable
from 2, 4, 6, 9 or 12 staons. Its probe input allows the connecon to a rain
sensor or a ow meter / water meter.
The LR-IS-FL requires the associaon with a LR-MB (relay WiFi/LoRa)
or an LR-BST. (However it can be used in bluetooth)
CREATE UN ACCOUNT
To benet from all LR-IS-FL features, please create a MySOLEM account.
1. Launch MySOLEM app from your smartphone and/or tablet.
2. Go to «My account» by typing on icon.
3. Follow the steps described on the app.

3
PAIRING
1. Remove the lower hatch to let appear the terminal.
3. Launch the MySOLEM app.
Step 2
2. Connect the 220/24 Vac power supply and replace the hatch.
5. Choose the LR-IS-FL from the list of nearby controllers.
7. To nish the pairing of your LR-IS-FL, follow the next steps described
in the app.
6. (Oponal) Dene a name and a security key for your controller and click
on the buon «Validate».
Note : To idenfy your LR-IS-FL among the nearby controllers, please refer
to the «Default name» present on his product label.
4. Tap on the «Add a module» buton or the «+» buton .
Security key
The security key allows to protect your controller. You can dene it during the
step 6 of the «ASSOCIATION» or access to further informaon by clicking on
the icon at the top right of your screen..

4
LR-MB PAIRING
Step 3
Note :
- The message «Connecon established» means that the connecon is
reliable.
- The message «No connecon established» means that it is necessary to
bring the LR-IS-FL closer to the LR-MB or vice versa.
To opmize the LoRaTM radio connecon between the LR-MB and the LR-IS-FL
controllers, we advise to install the LR-IS-FL in a plasc valve box under 800
meters to the LR-MB. We also advise to associate all your LR-IS-FL near the
LR-MB before installing them separately in the valve boxes.
2. Click on the top right icon to access to the product’s informaons.
4. Select the LR-MB you want to use.
7. Click on the buon to start the test.
3. Click on «Remote Access».
6. Go back to «Remote access» screen.
1. Select the LR-IS-FL programmer previously installed.
5. Click on the buon «Send» or on the boom of your screen to validate.
Once the pairing nished, you can test the connecon between
your LR-MB and your LR-IS-FL :

5
Connect the LR-IS-FL to the solenoids as described below.
Use 24V valves only.
LR-BST PAIRING
WIRING
Step 4
24V - S+ C C P 1 2 3 4 5 6 7 8 9 101112C
24V
1. On the applicaon, select your LR-BST, and enter pairing mode .
3. Tap the icon at the top right of your screen to access product’s infor-
maon.
4. Tap on «Accés à distance».
2. Select the LR-IS-FL programmer previously installed.
5. Select in the list the LR-BST inially chosen.
7. Click on the buon to start the test.
6. Return to the LR-IS-FL screen «Remote Access», previously seen.
Once the associaon is complete, you can test the connecon between your
LR-BST and your LR-IS-FL

6
Step 5
SET SENSOR
The LR-IS-FL has a -S+sensor input on which you can connect a rain sensor
or a pulse sensor / water meter aer cung the blue wire. Once the sensor is
connected, it is necessary to congure it in the applicaon.
2. Click on Add Sensor.
1. Using the MySOLEM mobile app, connect to your LR-IS-FL.
3. Select your sensor type and follow the instrucons given by the applicaon
Step 6
SET FLOWMETER
1. Check the «Instant Value».
Instant Value: Ensures that the volume consumed indicated on the water
meter is the same as the volume displayed on the applicaon. If a gap is
noted, check the wiring (polarity) or adjust the «COEFFICIENT» value.
High threshold (daily volume): maximum consumpon (in liter) that you
do not want to exceed in a period of 24h. If the goal is exceeded you will be
alerted immediately (by e-mail and nocaon smartphone and / or tablet).
Low threshold (daily volume): minimum consumpon (in liters) that you
want to achieve over a period of 24h. If the goal is not reached you will be
alerted the next day at 7am (by e-mail and nocaon smartphone and / or
tablet).
Leak alert volume: water volume threshold (in liter) from which you want to
be alerted.
2. Fill in the remaining elds.
Warning, by default there are no sensor congured.

7
Staon ow: for each staon, read the owmeter at me T (Cpt1), then at
me T + 5mn (Cpt2).
Make the calculaon (Cpt2 - Cpt1) / 5 => Flow (L / min)
In the applicaon ll in the results.
High Threshold (Staon Flow Alerts): Maximum consumpon warning
threshold in % of the calibrated ow of the channel. The «High threshold»
alert is immediate as soon as it is reached.
Low threshold (Staon Flow Alerts): Minimum consumpon warning
threshold in % of the calibrated ow of the channel. The «High threshold»
alert is immediate as soon as it is reached. For each staon ow alert you have
the possibility to dene the desired type of acon:
• No acon: watering connues.
• Permanent OFF: resuming watering requires a manual ON command (in
the applicaon on the programmer concerned).
• Inhibit the output: stops the staon concerned, requires the
acknowledgment of the alert (in the applicaon on the programmer
concerned) to reacvate the staon.
Stabilizaon me:
Time required before the water ow is stable when starng and stopping the
staon. It eliminates the peak ow (start) or leak (stop). The me is the same
for all staons.
During this period, the consumpon is not taken into account for triggering
alerts or acons.

8
24V - S+ C C P 1 2 3 4 5 6 7 8 9 101112C
24V
Flowmeter,
water meter
L/mn
Connect your + S - input to a water meter equipped with a ow sensor as
shown above. Use dry contact ow sensors or equivalent.
For polarized ow sensors, when wiring,observe the polarizaon :
Red wire -> + Black wire - > -

9
INFORMATION ON THE STATUS OF THE LED
Green LED : normal operaon
Blinking green LED : One channel is in progress (the ashing number
corresponds to the staon number acvated).
Green LED and Red Flashing : One channel is in progress and the rain sensor
is acvated or a staon is in progress and the product is in permanent OFF or
several days.
LED Red Fixed : the product is in inializaon mode
LED Red Flashing 2 mes : The programmer has lost me, reconnect to re-
synchronize.
LED Red Flashing 4 mes : One of the staons has a short circuit or is
overconsumpon. The other reason is that you probably have powered down
2 mes in a short me while a staon is sll in progress.
LED Red Flashing 5 mes : You have exceeded the me required to inialize
the mer. Repeat the inializaon procedure.
LED O : The product is not powered.

10
FAQ
What are the features required for the Bluetooth® product to work?
Android 4.3 (or more) Smartphones or tablets equipped with Bluetooth Smart
4.0 (or more). iOS 9.0 Apple iPhone or iPad running (or more) with Bluetooth
Smart 4.0 (or more)
Why does my staon not start?
It has to be assigned a me and a Program A, B or C to each staon. If several
staons are assigned to the same program, they will start one aer the other.
Why does Program B not start? If Program A departure me is the same than
Program B’s one, then the programs will be executed one aer the other.
What is output P for?
You can connect a master valve or a pump through a relay, on Poutput. It will
start automacally 2 sec before each staon and during each staon watering.
What are the controller’s output S (blue wire) for? You can plug a rain sensor
into Soutputs, to do that you need to cut the blue wire.
How does the rain sensor work? When connected to the yellow wire the rain
sensor acts on the 3 programs. If it is raining, programs A, B and C won’t start;
you must wait the probe to dry before the programs star again. The manual
control “All staons” is not aected by the rain sensor condions.
What is the Water Budget? The Water Budget allows to add a me percentage,
according to the me recorded by each staon. It is generally used during
seasonal changes (for example: summer to autumn, or spring to summer).
E.g.: If you entered Staon 1 = 1h on Program A and Staon 2 = 0h30 on
Program A. Then, if you enter a Water Budget for Program A at 120%, when
starng Program A, staons 1and 2will be increased by 20%, which means
1h12 for Staon 1 and 0h36 for Staon 2.
How can I restart the pairing or the pairing procedure?
To start the pairing procedure again, just bypass the 2 pins of the baery
pressure (baery prior removed) for 30s minimum.

11
If my device has no more baery, do I lose my programs?
No, they are not lost, they are automacally saved.
I would like to reset the sengs of my device. How do I do it?
Open the app, go to the product, then open the Sengs and select
«Erase programs and duraons».
GENERAL INFORMATIONS
READ THE FOLLOWING SAFETY INSTRUCTIONS CAREFULLY BEFORE
INSTALLING OR USING THE LR-IS-FL. BE SURE TO CAREFULLY OBSERVE
EMPLOYMENT PRECAUTIONS.
The LR-IS-FL must be installed indoor or under cover.
Install your product so that the socket outlet is near the equipment. The
socket is a disconnecng device, in case of problems, it must be easily
accessible at all mes. Make sure the power outlet to which your power
transformer is connected has overcurrent and circuit breaker type 16A
protecon. Use only the power supply unit supplied with the product:
INPUT : 230V ~ 50Hz OUTPUT : 24V ~ 0.75A
This symbol indicates that the product uses a Bluetooth®technology radio.
This symbol indicates that the product uses a LoRaTM technology radio.
The symbol «CE» indicates that this device complies with the European standards on
safety, health, environment and user protecon. Devices with the symbol «CE» are
intended for sale in Europe.
This symbol indicates that these types of electrical and electronic equipment must
be disposed of separately in European countries. Do not dispose of this device with
your household waste. Please use the collecon and recycling points available in your
country when you no longer need this device.

12
This symbol indicates that the power supply unit has a thermal protecon of 130 ° C.
~This symbol indicates that the supply voltage is an AC voltage.
This symbol indicates that the power supply is intended for indoor use only.
This symbol indicates that the power supply unit has a double insulaon class 2.

13
TECHNICAL FEATURES
DIMENSIONS
Version 2,4,6 Staons: Width 11 cm x Height 14,3 cm x Depth 4,2 cm
Version 9, 12 Staons: Width 16 cm x Height 14,3 cm x Depth 4,2 cm
INSTALLATION
Rain sensor or Water meter connecon
Master valve connecon
24V valves solenoid compable
Maximum wiring length with solenoids: 30 m
Ambient temperature of product use : -20°C à 60°C
ALIMENTATION
Power INPUT : 230V ~ 50Hz / OUTPUT : 24V ~ 0.75A 50Hz
FEATURES
Bluetooth®Smart 4.0 Low Energy [2400-2483.5]Mhz
LoRaTM radio communicaon
Permanent programming save
Internal clock saved in case of power failure < 30 s
V160920