Sony Handycam HDR-CX240 User manual

SERVICE MANUAL
SERVICE NOTE (Check the following note before the service.)
Revision History
Published by Sony Techno Create Corporation
Sony Corporation
LEVEL 2
HDR-CX240/CX240E/PJ240/PJ240E/PJ270/PJ270E/PJ275_L2
983477231.pdf
Digital HD Video Camera Recorder
The components identified by mark
0or dotted line with mark 0are
critical for safety.
Replace only with part number
specified.
Les composants identifiés par une
marque 0sont critiques pour la
sécurité.
Ne les remplacer que par une
pièce portant le numéro spécifié.
9-834-772-31
Ver. Date History Contents S.M. Rev.
issued
1.0 2014.01 Official Release — —
2014A08-1
© 2014.01
1-1. POWER SUPPLY DURING REPAIRS
1-2. PRECAUTION ON REPLACING THE VC-1023 BOARD
1-3. CHECKING THE Wi-Fi FUNCTION (HDR-PJ275)
1-4. SELF-DIAGNOSIS FUNCTION
1-5. NOTE ON REPLACING PROJECTOR UNIT (Projector Model)
Ver. 1.0 2014.01 US Model
Canadian Model
AEP Model
UK Model
North European Model
E Model
Australian Model
Chinese Model
Korea Model
Brazilian Model
HDR-CX240/CX240E/PJ240/PJ240E/
PJ270/PJ270E/PJ275
Photo: HDR-CX240/Black

– 2 –
HDR-CX240/CX240E/PJ240/PJ240E/PJ270/PJ270E/PJ275_L2
SPECIFICATIONS
System
Signal format:
NTSC color, EIA standards (HDR-CX240/
PJ240/PJ270/PJ275)
PAL color, CCIR standards (HDR-CX240E/
PJ240E/PJ270E)
HD TV
Movie recording format:
AVCHD (AVCHD format Ver.2.0
compatible):
Video: MPEG-4 AVC/H.264
Audio: Dolby Digital 2ch
Dolby Digital Stereo Creator*1
MP4:
Video: MPEG-4 AVC/H.264
Audio: MPEG-4 AAC-LC 2ch
*1 Manufactured under license from Dolby
Laboratories.
Photo file format:
DCF Ver.2.0 Compatible
Exif Ver.2.3 Compatible
MPF Baseline Compatible
Recording media (Movie/Photo):
Internal memory
HDR-PJ270/PJ270E/PJ275: 8 GB
Memory Stick Micro (Mark2) media
microSD card (Class 4 or faster)
The capacity that a user can use
(Approx.)
HDR-PJ270/PJ270E/PJ275:
7.75 GB*2
*2 1 GB equals 1 billion bytes, a portion of
which is used for system management and/
or application files. Only preinstalled dem-
onstration movie may be deleted.
Image device:
3.1 mm (1/5.8 type) CMOS Sensor
Recording pixels (photo, 16:9):
Max. 9.2 mega pixels (4 032 × 2 272)*3
Gross: Approx. 2 510 000 pixels
Effective (movie, 16:9)*4:
Approx. 2 100 000 pixels
Effective (photo, 16:9):
Approx. 2 290 000 pixels
Effective (photo, 4:3):
Approx. 1 710 000 pixels
Lens:
ZEISS Vario-Tessar Lens
27× (Optical), 54× (Clear Image
Zoom, while recording movies)*4,
320× (Digital)
F1.9 - F4.0
Focal length:
f=2.1 mm - 57.0 mm (3/32 in. - 2 1/4 in.)
When converted to a 35 mm still camera
For movies*4: 29.8 mm - 1 609.2 mm
(1 3/16 in. - 63 3/8 in.) (16:9)
For photos: 29.8 mm - 804.0 mm
(1 3/16 in. - 31 3/4 in.) (16:9)
Color temperature: [Auto], [One Push], [Indoor],
[Outdoor]
Minimum illumination:
6 lx (lux) (in default setting,
shutter speed 1/30 second (HDR-CX240/
PJ240/PJ270/PJ275) or
1/25 second (HDR-CX240E/
PJ240E/PJ270E))
3 lx (lux) ([Low Lux] is set to [On],
shutter speed 1/30 second (HDR-CX240/
PJ240/PJ270/PJ275) or
1/25 second (HDR-CX240E/
PJ240E/PJ270E))
*3 The unique image processing system of
Sony’s BIONZ-X allows still image resolu-
tion equivalent to the sizes described.
*4 [ SteadyShot] is set to [Standard] or
[Off].
Input/Output connectors
HDMI OUT jack: HDMI micro connector
PROJECTOR IN jack (HDR-PJ240/
PJ240E/PJ270/PJ270E/PJ275):
HDMI micro connector
USB jack: Type A (Built-in USB)
USB connector is only for output
(HDR-CX240E/PJ240E/PJ270E).
Multi Terminal
LCD monitor
Picture: 6.7 cm (2.7 type, aspect ratio 16:9)
Total number of pixels:
230 400 (960 × 240)
Projector (HDR-PJ240/PJ240E/
PJ270/PJ270E/PJ275)
Projection type: DLP
Light source: LED (R/G/B)
Focus: Manual
Throw Distance: 0.5 m (1.6 feet) or over
Contrast ratio: 1 500:1
Resolution (output): 640 × 360
Continuous projection time (when
using the supplied battery pack):
Approx. 1 h. 10 min.
Wireless LAN (HDR-PJ275)
Supported standard:
IEEE 802.11 b/g/n
Frequency: 2.4 GHz
Supported security protocols: WEP/
WPA-PSK/WPA2-PSK
Configuration method: WPS (Wi-Fi
Protected Setup)/manual
Access method: Infrastructure Mode
NFC: NFC Forum Type 3 Tag compliant
General
Power requirements: DC 3.6 V
(battery pack), DC 5 V 1 500 mA
(AC Adaptor)
USB Charging: DC 5 V 800 mA
Average power consumption:
During camera recording using LCD
monitor at normal brightness:
HDR-CX240/CX240E: 1.8 W
HDR-PJ240/PJ240E/PJ270/
PJ270E/PJ275: 1.9 W
Operating temperature: 0 °C to 40 °C
(32 °F to 104 °F)
Storage temperature: –20 °C to
+60 °C (–4 °F to +140 °F)
Dimensions (approx.):
HDR-CX240/CX240E:
54.0 mm × 59.5 mm × 128.0 mm
(2 1/4 in. × 2 3/8 in. × 5 1/8 in.) (w/h/d)
including the projecting parts
54.0 mm × 59.5 mm × 128.0 mm
(2 1/4 in. × 2 3/8 in. × 5 1/8 in.) (w/h/d)
including the projecting parts, and the
supplied rechargeable battery pack inserted
HDR-PJ240/PJ240E/PJ270/
PJ270E/PJ275:
59.0 mm × 59.5 mm × 128.0 mm
(2 3/8 in. × 2 3/8 in. × 5 1/8 in.)
(w/h/d) including the projecting parts
59.0 mm × 59.5 mm × 128.0 mm
(2 3/8 in. × 2 3/8 in. × 5 1/8 in.)
(w/h/d) including the projecting parts,
and the supplied rechargeable battery pack
inserted
Mass (approx.)
HDR-CX240/CX240E:
190 g (6.7 oz) main unit only 215 g (7.6 oz)
including the supplied rechargeable battery
pack
HDR-PJ240/PJ240E/PJ270/PJ270E/PJ275:
210 g (7.4 oz) main unit only
235 g (8.3 oz) including the
supplied rechargeable battery pack
AC Adaptor AC-UUD11
Power requirements: AC 100 V -
240 V, 50 Hz/60 Hz
Current consumption: 200 mA
Power consumption: 11 W
Output voltage: DC 5.0 V, 1 500 mA
Operating temperature: 0 °C to 50 °C
(32 °F to 122 °F)
Storage temperature: –20 °C to
+60 °C (–4 °F to +140 °F)
Rechargeable battery pack NP-BX1
Used battery: Lithium-ion battery
Maximum voltage: DC 4.2 V
Nominal voltage: DC 3.6 V
Maximum charge voltage: DC 4.2 V
Maximum charge current: 1.89 A
Capacity: 4.5 Wh (1 240 mAh)
Design and specifications of your camcorder and
accessories are subject to change without notice.
Model information table
Model CX240 CX240E PJ240 PJ240E PJ270 PJ270E PJ275
Destination US, CND, E,
KR, BR
AEP, UK, NE,
E, AUS, CH E, KR, BR AEP, UK, NE, E, AUS, CH CND, E E US
COLOR system NTSC PAL NTSC PAL NTSC PAL NTSC
Internal recording
media ––––
Internal memory
8 GB
Internal memory
8 GB
Internal memory
8 GB
LENS LSV-1610B LSV-1610B LSV-1610B LSV-1610B LSV-1610B LSV-1610B LSV-1610B
Projector – – 33333
GPS –––––––
EVF –––––––
Wi-Fi – –––––
3
NFC ––––––
3
Multi interface
shoe –––––––
Charging capacitor
(for flash) –––––––
MODEL GROUP
Projector Model: PJ240/PJ240E/PJ270/PJ270E/PJ275
Non Projector Model: CX240/CX240E
• Abbreviation
AUS: Australian model
BR: Brazilian model
CH: Chinese model
CND: Canadian model
KR: Korea model
NE: North European mode

– 3 –
HDR-CX240/CX240E/PJ240/PJ240E/PJ270/PJ270E/PJ275_L2
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0OR DOTTED LINE WITH
MARK 0ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST
ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPO-
NENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY
SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REM-
PLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT
LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES
SUPPLÉMENTS PUBLIÉS PAR SONY.
Caution
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
1. Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes and
bridges.
2. Check the interboard wiring to ensure that no wires are pinched or
contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly transistors,
that were installed during a previous repair. Point them out to the
customer and recommend their replacement.
4. Look for parts which, through functioning, show obvious signs of
deterioration. Point them out to the customer and recommend their
replacement.
5. Check the B+ voltage to see it is at the values specified.
6. Flexible Circuit Board Repairing
• Set the soldering iron tip temperature to 350 °C approximately.
• Do not touch the soldering iron on the same conductor of the circuit
board (within 3 times).
• Be careful not to apply force on the conductor when soldering or
unsoldering.
UNLEADED SOLDER
This unit uses unleaded solder.
Boards requiring use of unleaded solder are printed with the lead free
mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with the
lead free mark due to their particular size.)
: LEAD FREE MARK
Be careful to the following points to solder or unsolder.
• Set the soldering iron tip temperature to 350 °C approximately.
If cannot control temperature, solder/unsolder at high temperature
for a short time.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
Unleaded solder is more viscous (sticky, less prone to
flow) than ordinary solder so use caution not to let solder
bridges occur such as on IC pins, etc.
• Be sure to control soldering iron tips used for unleaded solder and
those for leaded solder so they are managed separately. Mixing un-
leaded solder and leaded solder will cause detachment phenomenon.
注意
如果电池更换不当会有爆炸危险。
只能用同样类型或等效类型的电池来更换。
务必按照说明处置用完的电池。

1-1
HDR-CX240/CX240E/PJ240/PJ240E/PJ270/PJ270E/PJ275_L2
1. SERVICE NOTE
1-1. POWER SUPPLY DURING REPAIRS
In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (4.2 Vdc), the power is shut off
so that the unit cannot operate.
These following method is available to prevent this.
Method:
Use the AC power adaptor.
1-2. PRECAUTION ON REPLACING THE VC-1023 BOARD
Note the following when replacing the board.
Destination Data
When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting.
Start the Adjust Manual in the Adjust Station and execute the “DESTINATION DATA WRITE”.
After the board replacement, the error of the built-in recording media may be displayed. In this case, execute the [DESTINATION DATA WRITE]
then the error will be cleared. If it is not cleared with [DESTINATION DATA WRITE], format the built-in recording media.
USB Serial Save
When you replace to the repairing board, get the data from the former one.
Start the Adjust Manual in the Adjust Station and perform “USB SERIAL SAVE” to get the data.
USB Serial No. and Product ID
The unit is shipped after an ID (USB Serial No.) unique to each unit and an ID (Product ID) unique to each model have been written.
These IDs have not been written in a new board for service, and therefore they must be entered after the board replacement.
After the board has been replaced with a board for service, start the Adjust Manual in the Adjust Station and execute the “PRODUCT ID & USB
SERIAL No. INPUT” and enter these IDs.
Note: A newly entered Product ID is not always equal to the ID before board replacement. If the new ID differs from the previous ID, it may cause a difference
from the ID registered by the customer.
Data for projector (Projector Model)
Before replacing the board with a spare board, acquire the following data from the current board.
• Fixed value (that shows irradiation performance of the projector).
• Serial number of the projector unit.
To acquire the data, start Adjust Manual from Adjust Station and select [Projector Data Reference] on the [DATA] tab.
Update of MAC Address (HDR-PJ275)
When replacing a VC board, the IC’s unique number (MAC address) must be reloaded.
After the board has been replaced with a board for service, perform the following procedure to reload the IC’s unique number (MAC address).
Note: Perform this operations after all work has been done.
1. Download the latest-version Adjust Manual.
2. Install the downloaded Adjust Manual.
3. Start the Adjust Manual, and execute “Wireless LAN Setting (MAC address)” on the ADJUST tab.
If “Wireless LAN check” is not executed and the backup data before replacement is restored, the MAC address in the Wi-Fi module does not match
the MAC address in the flash memory, causing an error during Wi-Fi transfer.
Note: The “LOAD AND WRITE” function in “ADJUSTMENT DATA BACKUP” on the DATA tab in the Adjust manual overwrites all data of the unit. Therefore,
the MAC address updated during the above procedure is also overwritten.
After the replacement and repair, the MAC address is changed, and thus the re-setting for connection devices is required. Accordingly, download the
Flyer of WLAN Reset (Flyer of WLAN Reset_9834752[][].pdf) and print out it, and attach it to the set when returning the set to customer.
About unit with Internal Memory Model (PJ270/PJ270E/PJ275)
After the board replacement, execute the procedure below first.
1. Execute the [DESTINATION DATA WRITE] of ADJUST tab in the Adjust Manual.
2. Execute the script files below. (Refer to the flowchart in Fig. 1)
• 14DdmMmcReadTestMINI_v6.vbe
• 14DdmMmcMakePartition_v6.vbe
Unless these script files are executed, the following symptoms may appear.
Make sure execute the above script files.
• The internal memory is not recognized as a media.
• The management file saved in the internal memory model cannot be repaired.
• The internal memory cannot be formatted.
START
END
Reactive the camcorder automatically
Disconnect the USB cable,
and turn off the power switch.
Select the "USB CONNECT" to establish
the connection
Execute
the "14DdmMmcReadTestMINI_v6.vbe"
(several second later)
Wait until "SetOverallReadMINI OK" display
(10 seconds later)
Reactive the camcorder automatically
Execute
the "14DdmMMCMakePartition_v6.vbe"
(several second later)
Wait until "MakePartition OK" display
During the power is turning-on,
pull-out the AC-adapter.
Then connect the AC-adapter Again
(It's running with blue color monitor.)
Connect to the PC with a USB cable,
and turn on the power switch.
*by SEUS driver
Fig.1

1-2
HDR-CX240/CX240E/PJ240/PJ240E/PJ270/PJ270E/PJ275_L2
1-3. CHECKING THE Wi-Fi FUNCTION (HDR-PJ275)
Perform the following procedure to check the Wi-Fi function.
Required equipment: Windows personal computer with Wi-Fi interface
1. Turn on the power of the unit.
2. Perform the following operations.
[MENU]→[Camera/Mic]→[ Shooting Assist]→[Ctrl with Smartphone]
3. When preparation for Wi-Fi has been completed, the following screen opens and a password for Wi-Fi connection is displayed.
Ctrl with Smartphone
Operate smartphone to connect to
this device via Wi-Fi.
SSID DIRECT-XXXX:HDR-XXXX
Password XXXXXXXX
Device Name HDR-XXXX
Wi-Fi
4. Confirm on the personal computer that the unit is detected as a connectable wireless network.
5. To further confirm that the unit is connectable, connect the unit to the personal computer and double-click the “current connection”from the icon
displayed on the notice field, make sure that the unit is displayed in the Wireless internet access column.
1-4. SELF-DIAGNOSIS FUNCTION
1-4-1. Self-diagnosis Function
When problems occur while the unit is operating, the self-diagnosis
function starts working, and displays on the Viewfinder or the LCD
screen what to do.
This function consists of two display; self-diagnosis display and service
mode display. Details of the self-diagnosis functions are provided in the
Instruction manual.
1-4-2. Self-diagnosis Display
When problems occur while the unit is operating, the counter of the
Viewfinder or the LCD screen shows a 4-digit display consisting of an
alphabet and numbers, which blinks at 3.2 Hz. This 5-character display
indicates the “repaired by:”, “block” in which the problem occurred, and
“detailed code”of the problem.
00
32C
Repaired by:
Refer to “1-4-3. Self-diagnosis Code Tabl e”.
Indicates the appropriate
step to be taken.
E.g.
13 ....
32 ....Turn on power again.
Block Detailed Code
Blinks at 3.2 Hz
C : Corrected by customer
E : Corrected by service
engineer
Format the “memory card”.
Viewfinder or LCD screen
1-4-3. Self-diagnosis Code Table
Self-diagnosis Code
Symptom/State Correction
Repaired by:
Block
Function
Detailed
Code
C 0 4 0 0 Non-standard battery is used. Use the designated battery.
C 0 6 0 0 The battery pack temperature is high. Change the battery pack or place it in a cool place.
C1 3 0 1Memory card is unformatted.
Memory card is broken.
Format the memory card.
Insert a new memory card.
C 1 3 0 2 Access error Remove the power source. Reconnect it again and operate your cam-
corder again.
C 1 3 0 3 Access error (External media) Turn power off and turn power on again.
C 1 3 0 4 Drive fault (External media) Turn power off and turn power on again.
C
E
32
61
60
00
Difficult to adjust focus
(Cannot initialize focus)
Retry turn the power on by the power switch. If it does not recover,
check the focus sensor of lens block (pin ek of CN4002 on the VC-
1023 board). If it is OK, check the focus motor drive IC (IC6800 on the
VC-1023 board).
E 2 0 0 0 Flash memory data are rewritten. Make flash memory data correct value. (Note 1)
E 3 1 0 0 Drive fault Turn power off and turn power on again.
E 4 1 0 0 Wi-Fi Module Hardware Error
PJ275:
Check that connection between CN4902 on the VC-1023 board and
CN2301 on the WF-1004 board by FP-2200 flexible board.
E6 1 1 0Zoom operations fault
(Cannot initialize zoom lens.)
Inspect the lens block zoom sensor (pin eg of CN4002 on the VC-1023
board when zooming is performed when the zoom lever is operated,
and the zoom motor drive circuit (IC6800 on the VC-1023 board) when
zooming is not performed.
*
*
*
()
*
Note 1: Start the Adjust Manual in the Adjust Station and refer to the “DESTINATION DATA WRITE”.
Note 2: Functions of codes with * mark are not provided in this unit.

1-3
HDR-CX240/CX240E/PJ240/PJ240E/PJ270/PJ270E/PJ275_L2
Note 2: Functions of codes with * mark are not provided in this unit.
Note 3: When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
Self-diagnosis Code
Symptom/State Correction
Repaired by:
Block
Function
Detailed
Code
E6 1 1 1
The abnormalities in initialization of
the focus lens and the abnormalities in
initialization of the zoom lens occurred
simultaneously.
Check both C: 32: 60 and E: 61: 10 of the self-diagnosis code.
E6 1 3 0Reset position detection error on the
stepper iris initializing
Turn the power on to open lens barrier. Disconnect the battery or power
cord, and then connect again.
Confirm that the iris blades in lens are working.
If iris blades do not working, check the iris motor drive IC in lens drive
block (pin wg, wh of CN4002 on theVC-1023 board).
If iris blades work normally, confirm that they are closing completely
and confirm following item.
• Case of the iris blades do not close normally. Replace the lens block.
• Case of “E: 61: 30” is appeared and iris blades closed completely.
Confirm that communication with lens block is normal.
• Case of LCD is not displayed normally. Check that connection between
CN6702 on CM-1004 board and CN4004 on VC-1023 board by FP-
2190 flexible board.
• Case of LCD is displayed normally. Replace the lens block.
E6 2 0 0
Handshake correction function does not
work well. (With PITCH angular veloc-
ity sensor output stopped.)
E:62:00
Inspect PITCH angular velocity sensors (SE7701 on the GY-1005
board) peripheral circuits.
E:62:01
Inspect YAW angular velocity sensors (SE7701 on the GY-1005 board)
peripheral circuits.
E6 2 0 1
Handshake correction function does not
work well. (With YAW angular velocity
sensor output stopped.)
E:62:00
Inspect PITCH angular velocity sensors (SE7701 on the GY-1005
board) peripheral circuits.
E:62:01
Inspect YAW angular velocity sensors (SE7701 on the GY-1005 board)
peripheral circuits.
E 6 2 0 2 Abnormality of IC for steadyshot. Turn power off and turn power on again.
E6 2 0 3IC for steadyshot and micro controller
communication abnormality among. Inspect the steadyshot circuit (IC6800 on the VC-1023 board).
E6 2 0 4Image vibration correction during hand-
shake function does not work.
Inspect the image vibration angular velocity sensors (SE7711 on the
VC-1023 board) peripheral circuits.
E 6 2 1 0 Shift lens initializing failure. Turn power off and turn power on again.
E 6 2 1 1 Shift lens overheating (Pitch) Turn power off and turn power on again.
E 6 2 1 2 Shift lens overheating (Yaw) Turn power off and turn power on again.
E 6 2 2 0 Abnormality of thermistor. Turn power off and turn power on again.
E 6 2 3 0 Abnormal CPU Turn power off and turn power on again.
E9 1 0 1Abnormality when flash is being
charged. Turn power off and turn power on again.
E 9 1 0 2 Abnormality of LED Video light. Turn power off and turn power on again.
E9 1 0 3Abnormality of LED Video light Tem-
perature detection. Turn power off and turn power on again.
E9 2 0 1Battery current value goes over the max
discharge current
Check the remaining battery power because this symptom maybe de-
pended on the remaining battery level, and confirm whether or not the
symptom is occurred after replacing the battery. If the symptom is still
occurred, replace the VC-1023 board.
E9 4 0 0Fault of writing or erasing the flash
memory
PJ270/PJ270E/PJ275:
Inspect the flash memory (IC8101 on the MM-102 board).
E 9 4 0 1 Internal flash memory fault PJ270/PJ270E/PJ275:
Inspect the flash memory (IC8101 on the MM-102 board).
*
*
*
*
*
*
1-5. NOTE ON REPLACING PROJECTOR UNIT (Projector Model)
Refer to the following flowchart when repairing or inspecting the projector’s projection function.
If you have received an indication on the projector’s projection function from the customer, check defective part according to the following flow-
chart.
When a defective part has been clarified, repair the projector according to the check result.
Note 1: The projector unit (copper plate in particular) becomes hot after it is used.
When replacing a part of the projector unit, wait until it is cooled down.
Wipe the lens gently with a soft cloth such as a cleaning cloth or glass cleaning cloth.
Note 2: Stubborn stains may be removed with a soft cloth such as a cleaning cloth or glass cleaning cloth lightly dampened with water.
Never use a solvent such as alcohol, benzene or thinner; acid, alkaline or abrasive detergent; or a chemical cleaning cloth, as they will damage the lens sur-
face.
Projector problem checking procedure (other than indication on brightness)
Indicated defective
projector received
Measure brightness.
( 2)
Yes
No
OK OK
NG NG
OK
NG
A
B
Indication on
brightness
Inspect projector
LED. ( 1)
1 Refer to the ADJUST tab of Adjust Manual.
2 Refer to the SERVICE tab of Adjust Manual.
Inspect projector
LED. ( 1)
END
-
-
-
-
-
Replace projector unit (light emitting block). (*1)
Replace PJ board. (*1)
Replace both projector unit (light emitting block)
and PJ board. (*1)
Projector Data Input
Fixed value input
Enter the number on the label attached to the unit.
Serial number input
LD40Syywwnnnnn Enter the red part.
(See page 1-4)
(See page 1-4)
Self-diagnosis Code
Symptom/State Correction
Repaired by:
Block
Function
Detailed
Code
E 9 4 0 2 BGM data error Check the CPU (IC6000 on the VC-1023 board).
E 9 5 0 0 GPS hardware error Turn power off and turn power on again.
E 9 6 0 0 Map area mount error Turn power off and turn power on again.
E 9 7 0 0 Projector hardware error Turn power off and turn power on again.
*
*
Note 2: Functions of codes with * mark are not provided in this unit.

HDR-CX240/CX240E/PJ240/PJ240E/PJ270/PJ270E/PJ275_L2
1-4E
Projector problem checking procedure (indication on brightness)
Yes
No
OK
NG
OK
NG
OK
NG
A
B
Indicated defective
projector received
Measure brightness.
( 2)
Measure brightness.
( 2)
Indication on
brightness
Inspect projector
LED. ( 1)
1 Refer to the ADJUST tab of Adjust Manual.
2 Refer to the SERVICE tab of Adjust Manual.
END
-
-
-
-
-
Replace projector unit (light emitting block). (*1)
Replace PJ board. (*1)
Replace both projector unit (light emitting block)
and PJ board. (*1)
Projector Data Input
Fixed value input
Enter the number on the label attached to the unit.
Serial number input
LD40Syywwnnnnn Enter the red part.
(See page 1-3)
(See page 1-3)

2-1
HDR-CX240/CX240E/PJ240/PJ240E/PJ270/PJ270E/PJ275_L2
2. REPAIR PARTS LIST
Follow the disassembly in the numerical order given.
IDENTIFYING PARTS
Link ACCESSORIES ASSEMBLY
･Abbreviation
AUS : Australian model
BR : Brazilian Model
CH : Chinese model
CND : Canadian model
KR : Korea model
NE : North European model
(ENGLISH)
NOTE:
• -XX, -X mean standardized parts, so they may have some differences from the original
one.
• Items marked “*” are not stocked since they are seldom required for routine service.
Some delay should be anticipated when ordering these items.
• The mechanical parts with no reference number in the exploded views are not supplied.
• Due to standardization, replacements in the parts list may be different from the parts
specified in the diagrams or the components used on the set.
• CAPACITORS:
uF: μF
• COILS
uH: μH
• RESISTORS
All resistors are in ohms.
METAL: metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F: nonflammable
• SEMICONDUCTORS
In each case, u: μ, for example:
uA...: μA... , uPA... , μPA... ,
uPB... , μPB... , μPC... , μPC... ,
uPD..., μPD...
The components identified by mark 0or dotted line
with mark 0are critical for safety.
Replace only with part number specified.
Les composants identifiés par une marque 0sont
critiques pour la sécurité.
Ne les remplacer que par une pièce portant le numéro
spécifié.
• Color Indication of Appearance Parts
Example:
(SILVER) : Cabinet’s Color
(Silver) : Parts Color
The components identified by mark contain confiden-
tial information.
Strictly follow the instructions whenever the components
are repaired and/or replaced.
Destroy and discard the prescribed board and IC after
they are replaced.
Les composants identifiés par le symbole contiennent
des informations confidentielles.
Suivez scrupuleusement les instructions chaque fois
qu'un composant est remplacé et / ou réparé.
Veuillez détruire et éliminer les circuits imprimés et / ou
les circuits intégrés que vous avez remplacés.
标识有 的元件包含机密信息。
更换或维修元件时，请严格遵守指⽰。
更换后的电路板和IC，应予以报废。
(JAPANESE)
【使用上の注意】
• ここに記載されている部品は,補修用部品であるため,回路図及びセットに付いてい
る部品と異なる場合があります。
• -XX,-Xは標準化部品のため,セットに付いている部品と異なる場合があります。
• *印の部品は常備在庫しておりません。
• コンデンサの単位でuFはμFを示します。
• 抵抗の単位Ωは省略してあります。
 金 被：金属被膜抵抗。
 サンキン：酸化金属被膜抵抗。
• インダクタの単位でuHはμHを示します。
• 半導体の名称でuA...,uPA...,uPB...,uPC...,uPD...等はそれぞれμA..., μPA...,
μPB...,μPC...,μPD...を示します。
図面番号で部品を指定するときは基板名又はブロッ
クを併せて指定してください。
お願い
0印の部品，または0印付の点線で囲まれた部品は，
安全性を維持するために，重要な部品です。
従って交換時は，必ず指定の部品を使用してくださ
い。
• 外装部品色表示
例：
 (SILVER)：セットの色を表す。
 (Silver) ：部品の色を表す。
印の部品には，秘密情報が含まれています。
修理の際は，指示に従った対応を行ってください。
交換後の対象基板及び対象ICは，破壊のうえ廃棄し
てください。
View Position
Right View
Left View
Front View
Bottom View
Top View
Back View
VC-1023
Projector Model Non Projector Model
1BT Panel
5F Panel Assy
3Hinge Cover (R)
2BT Lid Assy
4L Top Assy
8MM-102 Board
• FP-2060 Flexible Board
6Cabinet Block Assy
9Lens Block
• CM-1004 Board
• FP-2190 Flexible Board
7Control Switch Block
q; GY-1005 Board
• FP-2183 Flexible Board
qa VC-1023 Board
qs Cabinet (R) Block
• PJ-1009 Board
• PD-1029 Board
• FP-2106 Flexible Board
• FP-2193 Flexible Board
qs Cabinet (R) Block
• PD-1028 Board
• FP-2184 Flexible Board
PJ270/PJ270E/PJ275

2-2
HDR-CX240/CX240E/PJ240/PJ240E/PJ270/PJ270E/PJ275_L2
– JAPANESE –
– ENGLISH –
作業時の注意
フレキシブル基板の導電面に汚れやごみなどがないことを確認してください。
フレキシブル基板の導電面を素手で触れないようにしてください。
フレキシブル基板は，コネクターの奥までまっすぐに差し込んでください。(図1，図2，図3参照)
OK
(奥までまっすぐに差し込んである)
NG
(斜めに差し込んである)
NG
(差し込み不十分)
コネクター コネクター
フレキシブル
基板
基準線
フレキシブル
基板
コネクター コネクター
基準線
フレキシブル
基板
フレキシブル
基板
コネクター コネクター
基準線
フレキシブル
基板 フレキシブル
基板
図1 図2 図3
コネクターの開閉部を開ける際，A方向に開け過ぎないようにし
てください。
コネクターの開閉部を閉じる際，フレキシブル基板を矢印B方向
に押しながら，開閉部を均一に押してください。
開閉部
コネクター
フレキシブル基板
A
A
開閉部
絶縁面
コネクター
フレキシブル基板
B
• フラットケーブルおよびフレキシブル基板の端子面に欠け，
折れ等がないことを確認してください。
• 金メッキされているフレキシブル基板には，強い負担をかけ
ないでください。
先端の剥がれたメッキ部はカットして
除去してください。
（メッキ破片がコネクター内に残って
いる場合もあるので注意してください）
• コネクターを取り外す際に，線材部（極細）を持って引っ張る
と断線する恐れがありますので，絶対に線材部（極細）を持っ
て引っ張らないでください。
• 線材部（極細）を押さえながらコネクターを差し込むと，線材
部（極細）が断線する恐れがありますので，絶対に線材部（極細）
には負担をかけないでください。
OPERATION NOTES
Make sure that the conductive side of a flexible board does not have any stain or foreign materials.
Do not touch the conductive side of flexible boards with bare hands.
Plug in a flexible board straight, fully into the connector until it reaches the end inside. (Fig. 1, Fig. 2, Fig. 3)
OK
(The flexible board was plugged in straight
and completely)
NG
(The flexible board was plugged in
crooked.)
NG
(The flexible board was not plugged in
completely.)
Flexible
Board Flexible
Board
Connector Connector
Reference line Flexible
Board
Connector Connector
Flexible
Board
Reference line
Connector Connector
Flexible
Board
Flexible
Board
Reference line
Fig. 1 Fig. 2 Fig. 3
When opening the connector's holder in direction A, do not open
it with excessive force.
When closing the connector's holder, press it evenly while pushing
a flexible board in direction B.
Holder
Connector Flexible Board
A
AHolder
Insulation side
Connector Flexible Board
B
• Make sure that the flat cable and flexible board are not cracked
or bent at the contact end.
• Do not apply excessive force to the gilded flexible board.
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
• The proper way to disconnect a connector is to grab the con-
nector instead of the wires. If you pull on the wires, they might
be broken.
• The proper way to connect a connector is to grab the connector
instead of the wires. If you push on the wires, they might be
broken.

2-3
HDR-CX240/CX240E/PJ240/PJ240E/PJ270/PJ270E/PJ275_L2
2-1. EXPLODED VIEWS
2-1-1. OVERALL SECTION-1
(Projector Model)
Refer to page 2-4 about Non Projector Model.
Ref. No. Part No. Description Ref. No. Part No. Description
1 4-476-680-01 COVER (R (4411)), HINGE (BLACK)
1 4-476-680-11 COVER (R (4411)), HINGE (SILVER)
1 4-476-680-21 COVER (R (4411)), HINGE (RED)
2 A-1998-711-A PANEL ASSY (441B), F (BLACK)
2 A-1998-713-A PANEL ASSY (441S), F (SILVER)
2 A-1998-714-A PANEL ASSY (441R), F (RED)
3 A-1998-666-A LTOP ASSY (441B) (BLACK) (EXCEPT PJ275))
3 A-1998-668-A LTOP ASSY (441S) (SILVER)
3 A-1998-709-A LTOP ASSY (441R) (RED)
3 A-2037-583-A LTOP ASSY (441BW) (BLACK) (PJ275)
4 4-473-996-01 PANEL (441), BT (BLACK)
4 4-473-996-21 PANEL (441), BT (SILVER)
4 4-473-996-31 PANEL (441), BT (RED)
5 A-1999-099-A LID ASSY (441B), BT (BLACK)
5 A-1999-101-A LID ASSY (441S), BT (SILVER)
5 A-1999-102-A LID ASSY (441R), BT (RED)
#2 2-635-562-31 SCREW (M1.7)
#12 3-080-204-21 SCREW, TAPPING, P2
1. Remove in numerical order (1to 5) in the left figure.
DISASSEMBLY
1#12 X 1
Screw
Left View
#12
#2: M1.7 X 4.0
(Black)
2-635-562-31
4.0
1.7
#12: M1.7 X 5.0 (Tapping)
(Black)
3-080-204-21
1.7
5.0
3Open the LCD (1) →#2 X 2
Bottom View
Back View
#2
#2
1
4#2 X 1 →#12 X 1 →#2 X 2 →#12 X 1
Right View
Back View
Left View
Bottom View
#2
#12
#2
#12
機種によって形状がイラストと異なる場合があります。
The shape may be different from the illustration depending
on models.
14
25
43
5231
(Claws)
(Claws)
Overall Section-2
(Projector Model)
(See Page 2-5)
#12
#12
#2
1
#2
#2
#2
#12
A
A

2-4
HDR-CX240/CX240E/PJ240/PJ240E/PJ270/PJ270E/PJ275_L2
2-1-2. OVERALL SECTION-1
(Non Projector Model)
Refer to page 2-3 about Projector Model.
Ref. No. Part No. Description Ref. No. Part No. Description
51 4-476-679-01 COVER (R (441)), HINGE (BLACK)
51 4-476-679-11 COVER (R (441)), HINGE (BLUE)
51 4-476-679-21 COVER (R (441)), HINGE (SILVER)
52 A-1998-711-A PANEL ASSY (441B), F (BLACK)
52 A-1998-712-A PANEL ASSY (441L), F (BLUE)
52 A-1998-713-A PANEL ASSY (441S), F (SILVER)
53 A-1998-666-A LTOP ASSY (441B) (BLACK)
53 A-1998-667-A LTOP ASSY (441L) (BLUE)
53 A-1998-668-A LTOP ASSY (441S) (SILVER)
54 4-473-996-01 PANEL (441), BT (BLACK)
54 4-473-996-11 PANEL (441), BT (BLUE)
54 4-473-996-21 PANEL (441), BT (SILVER)
55 A-1999-099-A LID ASSY (441B), BT (BLACK)
55 A-1999-100-A LID ASSY (441L), BT (BLUE)
55 A-1999-101-A LID ASSY (441S), BT (SILVER)
#2 2-635-562-31 SCREW (M1.7)
#12 3-080-204-21 SCREW, TAPPING, P2
154
255
453
552 351
(Claws)
(Claws)
Overall Section-2
(Non Projector Model)
(See Page 2-6)
#12
#12
#2
1
#2
#2
#12
#2
A
A
1. Remove in numerical order (1to 5) in the left figure.
DISASSEMBLY
1#12 X 1
Screw
Left View
#12
#2: M1.7 X 4.0
(Black)
2-635-562-31
4.0
1.7
#12: M1.7 X 5.0 (Tapping)
(Black)
3-080-204-21
1.7
5.0
3Open the LCD (1) →#2 X 2
Bottom View
Back View
#2
#2
1
4#2 X 1 →#12 X 1 →#2 X 2 →#12 X 1
Right View
Back View
Left View
Bottom View
#2
#12
#2
#12
機種によって形状がイラストと異なる場合があります。
The shape may be different from the illustration depending
on models.

2-5
HDR-CX240/CX240E/PJ240/PJ240E/PJ270/PJ270E/PJ275_L2
2-1-3. OVERALL SECTION-2
(Projector Model)
Refer to page 2-6 about Non Projector Model.
Ref. No. Part No. Description Ref. No. Part No. Description
101 A-1998-529-A CABINET BLOCK ASSY (441)
102 A-1992-843-A VC-1023 BOARD, COMPLETE (SERVICE)
103 4-476-262-01 RETAINER (453), HDMI
104 1-889-184-11 FP-2190 FLEXIBLE BOARD
105 8-848-901-01 DEVICE, LENS LSV-1610B
106 1-856-432-21 FILTER BLOCK, OPTICAL (Note 2)
107 4-436-733-01 RUBBER (1610), SEAL
108 A-1903-090-A CM-1004 BOARD, COMPLETE (Note 1)
109 A-1998-288-A CABINET ASSY (449), INNER
110 1-887-155-11 FP-2060 FLEXIBLE BOARD (PJ270/PJ270E/PJ275)
111 A-1992-841-A MM-102 BOARD, COMPLETE (PJ270/PJ270E/PJ275)
112 1-838-712-32 CABLE, BUILT-IN USB
113 1-492-709-11 SWITCH BLOCK, CONTROL (PS45300)
114 A-1992-840-A GY-1005 BOARD, COMPLETE
115 1-889-096-11 FP-2183 FLEXIBLE BOARD
116 4-476-291-01 BATTERY (441), DUMMY
117 1-889-592-11 AN-1006 FLEXIBLE BOARD (PJ275)
118 1-889-209-11 FP-2200 FLEXIBLE BOARD (PJ275)
119 A-2040-416-A NFC BLOCK ASSY (14Y-TERA) COMP (PJ275) (Note 3)
120 A-1992-200-A WF-1004 BOARD, COMPLETE (PJ275)
121 1-889-222-11 FP-2201 FLEXIBLE BOARD
122 4-282-293-01 SHEET (ST (381)), SHIELD
*BT901 1-780-826-11 TERMINAL BOARD, BATTERY
MIC901 1-542-948-11 MICROPHONE UNIT
SP901 1-858-075-41 SPEAKER (1.8CM)
#2 2-635-562-31 SCREW (M1.7)
#12 3-080-204-21 SCREW, TAPPING, P2
#140 2-635-562-01 SCREW (M1.7)
#172 2-178-410-01 TITE (UB TITE) 1.4
1. Remove in numerical order (1to 5) in the left figure.
DISASSEMBLY
1#140 X 1
Screw
Left View
#140
#2: M1.7 X 4.0
(Black)
2-635-562-31
4.0
1.7
#12: M1.7 X 5.0 (Tapping)
(Black)
3-080-204-21
1.7
5.0
#140: M1.7X 2.0
(Black)
2-635-562-01
2.0
1.7
2#2 X 2
Top View
Left View
#2 #2
3#2 X 2
Top View
Right View
#2 #2
機種によって形状がイラストと異なる場合があります。
The shape may be different from the illustration depending
on models.
PJ270/PJ270E
/PJ275
PJ275
107
#172
108
(including CP001
(CMOS imager))
(Note 1)
#140
#140
110
101
122
1111
#2
#2
#2
#12
#12
#12
A
D
A
D
B
#2
#2
112
B
C
104
2113
3
109
4114
5102
BT901
115 121
116
103
105
C
#2
MIC901
ns
ns
SP901
120
119
118
117
106
(Note 2)
(Note 3)
Cabinet (R) Section
(Projector Model)
(See page 2-7)
4#12 X 1
Front View
#12
5#2 X 1 →#12 X 1
Top View
Right View
#12
#2
Note
Note 1: Be sure to read “Precautions for Replacement of Imager”
on page 6-1 of Level 3 when changing the imager.
Note 1: イメージャの交換時はLevel3の6-1ページ，“イメージャ交
換時の注意”を必ずお読みください。
Note 2: Refer to “Assembly-2: How to distinguish the side of Optical
Filter Block facing to Lens Device”.
Note 2: “Assembly-2:Howto distinguishthesideofOpticalFilter
BlockfacingtoLensDevice”を参照してください。
Note 3: Be careful not to break the NFC Block Assy. Note 3: NFC部組を折らないよう注意してください。
#172: M1.4 X 4.0 (Tapping)
(Black)
2-178-410-01
1.4
4.0

2-6
HDR-CX240/CX240E/PJ240/PJ240E/PJ270/PJ270E/PJ275_L2
2-1-4. OVERALL SECTION-2
(Non Projector Model)
Refer to page 2-5 about Projector Model.
ns: not supplied
Ref. No. Part No. Description Ref. No. Part No. Description
151 A-1998-529-A CABINET BLOCK ASSY (441)
152 A-1992-842-A VC-1023 BOARD, COMPLETE
153 4-476-262-01 RETAINER (453), HDMI
154 1-889-184-11 FP-2190 FLEXIBLE BOARD
155 8-848-901-01 DEVICE, LENS LSV-1610B
156 1-856-432-21 FILTER BLOCK, OPTICAL
157 4-436-733-01 RUBBER (1610), SEAL
158 A-1903-090-A CM-1004 BOARD, COMPLETE (including CP001
(CMOS imager)) (Note 1)
159 A-1998-288-A CABINET ASSY (449), INNER
160 1-838-712-32 CABLE, BUILT-IN USB
161 1-492-709-11 SWITCH BLOCK, CONTROL (PS45300)
162 A-1992-840-A GY-1005 BOARD, COMPLETE
164 1-889-096-11 FP-2183 FLEXIBLE BOARD
165 4-476-291-01 BATTERY (441), DUMMY
166 1-889-222-11 FP-2201 FLEXIBLE BOARD
*BT901 1-780-826-11 TERMINAL BOARD, BATTERY
MIC901 1-542-948-11 MICROPHONE UNIT
SP901 1-826-837-91 SPEAKER (1.3CM)
#2 2-635-562-31 SCREW (M1.7)
#12 3-080-204-21 SCREW, TAPPING, P2
#172 2-178-410-01 TITE (UB TITE) 1.4
1. Remove in numerical order (1to 4) in the left figure.
DISASSEMBLY
Screw
#2: M1.7 X 4.0
(Black)
2-635-562-31
4.0
1.7
#12: M1.7 X 5.0 (Tapping)
(Black)
3-080-204-21
1.7
5.0
#172: M1.4 X 4.0 (Tapping)
(Black)
2-178-410-01
1.4
4.0
1#2 X 1→#12 X 1
Top View
Left View
#2 #12
Note
Note 1: Be sure to read “Precautions for Replacement of Imager”
on page 6-1 of Level 3 when changing the imager.
Note 1: イメージャの交換時はLevel3の6-1ページ，“イメージャ交
換時の注意”を必ずお読みください。
Note 2: Refer to “Assembly-2: How to distinguish the side of Optical
Filter Block facing to Lens Device”.
Note 2: “Assembly-2:Howto distinguishthesideofOpticalFilter
BlockfacingtoLensDevice”を参照してください。
機種によって形状がイラストと異なる場合があります。
The shape may be different from the illustration depending
on models.
157
#172
158
(including CP001
(CMOS imager))
(Note 1)
156
(Note 2)
155
151
#2
#12
#172
#12
#12
A
A
B
#2
#2
160
B
C
154
1161
2159
3162
4152
164
165
153
C
#12
1
MIC901
ns
ns
SP901
BT901
166
Cabinet (R) Section
(Non Projector Model)
(See page 2-9)
2#12 X 1 →Open the LCD (1) →#2 X 1
Top View
Right View
#12 #2
1
3#12 X 1
Front View
#12
4#2 X 1 →#12 X 1
Top Vi ew
Right View
#12
#2

2-7
HDR-CX240/CX240E/PJ240/PJ240E/PJ270/PJ270E/PJ275_L2
2-1-5. CABINET (R) SECTION
(Projector Model)
Refer to page 2-9 about Non Projector Model.
ns: not supplied
Ref. No. Part No. Description Ref. No. Part No. Description
201 A-1998-660-A CABINET (C) ASSY (4411B), P (PJ270/PJ270E
(BLACK))
201 A-1998-661-A CABINET (C) ASSY (4411S), P (PJ270/PJ270E
(SILVER))
201 A-1998-662-A CABINET (C) ASSY (4411R), P (PJ270 (RED))
201 A-1998-663-A CABINET (C) ASSY (4411B), P (PJ240/PJ240E
(BLACK))
201 A-1998-664-A CABINET (C) ASSY (4411S), P (PJ240/PJ240E
(SILVER))
201 A-1998-665-A CABINET (C) ASSY (4411R), P (PJ240E (RED))
201 A-2037-582-A CABINET (C) ASSY (4411BW), P (PJ275 (BLACK))
202 4-476-583-01 SHEET PJ (4441)
203 4-476-569-01 HEAT SINK (4411), P
204 A-1903-100-A FP-2106 FLEXIBLE BOARD, COMPLETE
205 4-272-354-01 SHEET, P RADIATION
206 4-272-358-01 CUSHION, P
207 A-1847-133-A LSV-1580A (Note 2)
208 A-1994-765-A PJ-1009 BOARD, COMPLETE
209 3-283-643-21 SCREW, TRIPOD (Note 3)
*210 3-283-835-01 CUSHION, SP
211 A-1998-639-A CABINET (R) ASSY (4411)
#2 2-635-562-31 SCREW (M1.7)
#30 3-086-156-11 SCREW B1.2
#288 2-187-345-21 SCREW (M1.7), P2 (Note 1)
(Claws)
Adjust the position.
#2
202
(Claw)
(Claws)
(Claws)
(Claws)
201
203
#30
208
206
207
(Note 2)
204
#288
(Note 1)
#2
ns
LCD Section
(Projector Model)
(See Page 2-8)
209
(Note 3)
211
205
210
Screw
#2: M1.7 X 4.0
(Black)
2-635-562-31
4.0
1.7
#30: M1.2 X 3.5 (Tapping)
(White)
3-086-156-11
3.5
1.2
#288: M1.7 X 2.5
(Black)
2-187-345-21
2.5
1.7
Note
Note 3: When removing / attaching this part, be careful not to dam-
age the peripheral parts.
Note 3: この部品を取り外し，取り付けるときは，周囲の部品を破
損しないよう注意してください。
Note 1: This screw cannot be reused. Discard the screw removed
once in servicing. Instead, use a new screw.
Note 1: このねじは再利用することができません。サービス対応時
に一度でも外した場合は新品のねじと交換してください。
PRECAUTIONS WHEN HOLDING THE PROJECTOR UNIT
Lens part
Sheet
The projector unit (copper plate in particular) becomes hot after it is used.
When replacing a part of the projector unit, wait until it is cooled down.
Copper Plate
Copper Plate
Contact area of
Flexible Board
Terminal of
Connector
Note 2:
Very weak
(Don't hold)
Lever
Weak
(Handling attention)
Have to wear
finger stall
プロジェクターを使用した後は，プロジェクターユニットが熱くなっています。
特に銅板の部分は高温になります。
部品を交換する時は，温度が下がってから作業を行なってください。
プロジェクターユニットを持つ際の注意
銅板
銅板 コネクタ部
フレキ接点
レバー
非常に弱い 弱い 指サック着用
のこと
シート
レンズ部
Note 2:

2-8
HDR-CX240/CX240E/PJ240/PJ240E/PJ270/PJ270E/PJ275_L2
251 A-1994-888-A PD-1029 BOARD, COMPLETE
252 4-476-572-01 BUTTON (4411), PLAYBACK (PJ)
253 4-209-715-01 JOYSTICK
254 4-476-577-01 INSULATING SHEET (4441)
255 4-476-565-01 RETAINER (4411), LCD
256 4-476-566-01 CUSHION (4441), LCD
257 4-476-564-01 PLATE (4411), PANEL GROUND
258 4-476-574-01 KNOB (4411), FOCUS
259 4-476-563-01 CABINET (M (4411)), P
260 1-889-187-11 FP-2193 FLEXIBLE BOARD (Note 3)
Ref. No. Part No. Description
Ref. No. Part No. Description
261 4-476-674-01 COVER (C (4411)), HINGE (BLACK)
261 4-476-674-11 COVER (C (4411)), HINGE (SILVER)
261 4-476-674-21 COVER (C (4411)), HINGE (RED)
262 X-2585-820-2 HINGE (P) (Y (4071)) ASSY
263 1-471-573-11 MAGNET (Note 2)
264 4-476-571-01 COVER (M (4411)), HINGE
BH4600 1-251-928-21 SOCKET, BATTERY
BT4600 1-756-134-15 BATTERY, LITHIUM (SECONDARY)
LCD901 1-811-218-11 LCD MODULE
#2 2-635-562-31 SCREW (M1.7)
#11 3-078-890-11 SCREW, TAPPING
#288 2-187-345-21 SCREW (M1.7), P2 (Note 1)
Screw
#2: M1.7 X 4.0
(Black)
2-635-562-31
4.0
1.7
#11: M1.7 X 4.0 (Tapping)
(Silver)
3-078-890-11
4.0
1.7
#288: M1.7 X 2.5
(Black)
2-187-345-21
2.5
1.7
2-1-6. LCD SECTION
(Projector Model)
Refer to page 2-9 about Non Projector Model.
ns: not supplied
Note
Note 4: Replace the battery holder (BH4600) together when replac-
ing the lithium storage battery (BT4600) on the PD-1029
board.
(The battery holder removed once cannot be used again.)
When mounting these parts, mount new battery holder first
and attach new lithium storage battery next.
Note 4: PD-1029基板のリチウム蓄電池(BT4600)を交換する場合は
バッテリホルダ(BH4600) も同時に新品に交換してくださ
い。
 (一度使用したバッテリホルダは再使用できません。)
 部品取り付けの際は，先にバッテリホルダを取り付けてか
らリチウム蓄電池を装着してください。
Note 3: Refer to “Assembly-1: Installation Method of FP-2184/FP-
2193”.
Note 3: “Assembly-1:InstallationMethodofFP-2184/FP-2193”を参
照してください。
Note 1: This screw cannot be reused. Discard the screw removed
once in servicing. Instead, use a new screw.
Note 1: このねじは再利用することができません。サービス対応時
に一度でも外した場合は新品のねじと交換してください。
#2
BH4600
(Note 4)
BT4600
(Note 4)
260
(Note 3)
#11
253
254
251
255
256
257
258
259
LCD901
ns
#288
(Note 1)
(Claws)
263
(Note 2)
264
262
261
: BT4600 (LITHIUM SECONDARY BATTERY)
Board on the mount position.
(See page 6-46 of Level 3)
252
Note 2: Install the magnet with
the marking oriented
as shown below.
Marking
Note 2: マグネットを取付ける
際は，マ−キング面を
図の位置にあわせて
ください。
マーキング

2-9
HDR-CX240/CX240E/PJ240/PJ240E/PJ270/PJ270E/PJ275_L2
301 4-476-668-01 CABINET (C (441)), P (BLACK)
301 4-476-668-21 CABINET (C (441)), P (SILVER)
302 4-274-987-01 TAPE (AS 1/2) (C)
303 A-1994-877-A PD-1028 BOARD, COMPLETE
304 4-476-572-11 BUTTON (4411), PLAYBACK (PJ)
305 4-209-715-01 JOYSTICK
306 4-446-970-01 INSULATING SHEET (409)
307 4-476-576-01 PLATE (441), PANEL GROUND
308 4-476-575-01 CABINET (M (441)), P
309 1-889-097-11 FP-2184 FLEXIBLE BOARD (Note 3)
310 3-283-643-21 SCREW, TRIPOD (Note 5)
311 4-476-673-01 COVER (C (441)), HINGE (BLACK)
311 4-476-673-21 COVER (C (441)), HINGE (SILVER)
Ref. No. Part No. Description
Ref. No. Part No. Description
312 X-2585-819-1 HINGE (Y (409)) ASSY, T TYPE
313 1-471-573-11 MAGNET (Note 2)
*314 3-283-835-01 CUSHION, SP
315 A-1998-638-A CABINET (R) ASSY (441)
BH4500 1-251-928-21 SOCKET, BATTERY (Note 4)
BT4500 1-756-134-15 BATTERY, LITHIUM (SECONDARY) (Note 4)
LCD901 1-811-218-11 LCD MODULE
#2 2-635-562-31 SCREW (M1.7)
#11 3-078-890-11 SCREW, TAPPING
#288 2-187-345-21 SCREW (M1.7), P2 (Note 1)
2-1-7. CABINET (R) SECTION
(Non Projector Model)
Refer to page 2-7 about Projector Model.
ns: not supplied
Screw
#2: M1.7 X 4.0
(Black)
2-635-562-31
4.0
1.7
#11: M1.7 X 4.0 (Tapping)
(Silver)
3-078-890-11
4.0
1.7
#288: M1.7 X 2.5
(Black)
2-187-345-21
2.5
1.7
#2
LCD901
#2
ns
ns
ns
ns
310
(Note 5)
#288
(Note 1)
313
(Note 2)
#288
(Note 1)
(Claws)
302 305
304
303
301
BH4500
(Note 4)
BT4500
(Note 4)
309
(Note 3)
315
#11
#2
(Claws)
(Claws)
(Claws)
306
307
308
311
312
314
Note
Note 4: Replace the battery holder (BH4500) together when replac-
ing the lithium storage battery (BT4500) on the PD-1029
board.
(The battery holder removed once cannot be used again.)
When mounting these parts, mount new battery holder first
and attach new lithium storage battery next.
Note 4: PD-1029基板のリチウム蓄電池(BT4500)を交換する場合は
バッテリホルダ(BH4500) も同時に新品に交換してくださ
い。
 (一度使用したバッテリホルダは再使用できません。)
 部品取り付けの際は，先にバッテリホルダを取り付けてか
らリチウム蓄電池を装着してください。
Note 3: Refer to “Assembly-1: Installation Method of FP-2184/FP-
2193”.
Note 3: “Assembly-1:InstallationMethodofFP-2184/FP-2193”を参
照してください。
Note 1: This screw cannot be reused. Discard the screw removed
once in servicing. Instead, use a new screw.
Note 1: このねじは再利用することができません。サービス対応時
に一度でも外した場合は新品のねじと交換してください。
Note 2: Install the magnet with
the marking oriented
as shown below.
Marking
Note 2: マグネットを取付ける
際は，マ−キング面を
図の位置にあわせて
ください。
マーキング
Note 5: When removing / attaching this part, be careful not to dam-
age the peripheral parts.
Note 5: この部品を取り外し，取り付けるときは，周囲の部品を破
損しないよう注意してください。

HDR-CX240/CX240E/PJ240/PJ240E/PJ270/PJ270E/PJ275_L2
2-10E
ACCESSORIES
901 902 903 904 905
Ref. No. Part No. Description
 8-022-359-31 Rechargeable battery pack NP-BX1/UC (US, CND)
8-022-359-50 Rechargeable battery pack NP-BX1/CE (EXCEPT US, CND, NE, CH)
8-022-359-55 Rechargeable battery pack NP-BX1/RU (NE)
8-022-359-71 Rechargeable battery pack NP-BX1/CN (CH)
Ref. No. Part No. Description
901 1-492-768-11 AC Adaptor (US, CND, E: NTSC)
901 1-492-768-21 AC Adaptor (CH)
901 1-492-769-11 AC Adaptor (AEP, NE, E (EXCEPT NTSC, Saudi))
901 1-492-769-21 AC Adaptor (BR)
901 1-492-769-31 AC Adaptor (KR)
901 1-492-770-11 AC Adaptor (AUS)
901 1-492-771-11 AC Adaptor (UK, E: Saudi)
902 1-569-007-12 Conversion (2P) Adaptor (E: NTSC)
903 1-838-714-31 USB connection support cable
904 1-846-028-21 HDMI cable
*905 4-531-548-11 Operating Guide (ENGLISH)
*905 4-531-548-21 Operating Guide (SPANISH)
*905 4-531-548-41 Operating Guide (TRADITIONAL CHINESE)
Ref. No. Part No. Description
*905 4-531-549-21 Operating Guide (KOREAN)
*905 4-531-550-11 Operating Guide (GERMAN, DUTCH, ITALIAN,
PORTUGUESE)
*905 4-531-550-21 Operating Guide (GREEK, POLISH, CZECH,
HUNGARIAN)
*905 4-531-550-31 Operating Guide (SLOVAK, SWEDISH, DANISH,
FINNISH, ROMANIAN)
*905 4-531-550-41 Operating Guide (RUSSIAN, UKRAINIAN)
*905 4-531-550-51 Operating Guide (SIMPLIFIED CHINESE)
*905 4-531-550-61 Operating Guide (ARABIC, PERSIAN)
*905 4-531-550-71 Operating Guide (TURKISH)
*905 4-531-551-31 Operating Guide (SIMPLIFIED CHINESE)
This Item is not supplied with the unit as an accessory, but it is prepared as a service part.
When the customer requests printed one, ask Head Quarter.
941
Ref. No. Part No. Description
*941 4-531-544-11 Help Guide (ENGLISH)
*941 4-531-544-21 Help Guide (FRENCH)
*941 4-531-544-31 Help Guide (SPANISH)
*941 4-531-544-41 Help Guide (GERMAN)
*941 4-531-544-51 Help Guide (ITALIAN)
*941 4-531-544-61 Help Guide (DUTCH)
*941 4-531-544-71 Help Guide (PORTUGUESE)
*941 4-531-544-81 Help Guide (BRAZILIAN PORTUGUESE)
*941 4-531-544-91 Help Guide (TURKISH)
*941 4-531-545-11 Help Guide (GREEK)
*941 4-531-545-21 Help Guide (CZECH)
*941 4-531-545-31 Help Guide (HUNGARIAN)
*941 4-531-545-41 Help Guide (SLOVAK)
*941 4-531-545-51 Help Guide (POLISH)
*941 4-531-545-61 Help Guide (SWEDISH)
Ref. No. Part No. Description
*941 4-531-545-71 Help Guide (DANISH)
*941 4-531-545-81 Help Guide (FINNISH)
*941 4-531-545-91 Help Guide (ROMANIAN)
*941 4-531-546-11 Help Guide (RUSSIAN)
*941 4-531-546-21 Help Guide (UKRAINIAN)
*941 4-531-546-31 Help Guide (TRADITIONAL CHINESE)
*941 4-531-546-41 Help Guide (SIMPLIFIED CHINESE)
*941 4-531-546-51 Help Guide (KOREAN)
*941 4-531-546-61 Help Guide (ARABIC)
*941 4-531-546-71 Help Guide (PERSIAN)
*941 4-531-546-81 Help Guide (INDONESIAN)
*941 4-531-546-91 Help Guide (THAI)

HDR-CX240/CX240E/PJ240/PJ240E/PJ270/PJ270E/PJ275_L2
3-1E
3. ASSEMBLY
Assembly-1: The Method of attachment of FP-2184/2193 Flex-
ible Board
1Fold dotted line parts of the FP-2184/FP-2193 flexible
board as shown in figure.
Adhesive tape Adhesive tape
Adhesive tape
Adhesive tape
Adhesive tape
Adhesive tape
Valley fold
Valley fold
Mountain fold
FP-2193
Flexible Board
FP-2184
Flexible Board
Mountain fold
Valley fold
2Roll the FP-2184/2193 Flexible Board 2 times
in the Hinge Assy as shown in figure.
3Install the Cover (M) Hinge/Cover (C) Hinge.
Cover (M) Hinge
Cover (C) Hinge
2 Times
4Attach the FP-2184/2193 Flexible Board board
as shown in figure.
Flexible Board
Hinge Assy
FP-2184/2193
Flexible Board
Assembly-2: How to distinguish the side of Optical Filter Block
facing to Lens Device
• IR cut coating surface
The red coating is reflected.
• The other surface
The red coating is
not reflected. • Side view
The red belt
is seen.
Lens Device side
Lens Device side
Hold it with tweezers or the like.
Optical Filter Block
[IR Cut Coated Side] [The Other Side]
The one side of the Optical Filter Block has treated with IR cut coating.
Mount the Optical Filter Block facing the IR cut coated side to the lens
device. Distinguish the IR cut coated side from the other by applying the
fluorescent light to the Optical Filter Block in the dark place (cut off the
outside light).

HDR-CX240/CX240E/PJ240/PJ240E/PJ270/PJ270E/PJ275_L2
7-1E
7. ADJUSTMENT
(ENGLISH)
For adjusting these models, the Adjust manual and the Adjust station are required.
Adjust station
It is the software to start up Adjust manual for each model.
The installer of the Adjust station and the installation manual are attached, be sure to confirm the contents of them.
Adjust manual
It is the software to adjust and check digital cameras and camcorders for service.
The installer of the Adjust manual and the installation manual are attached, be sure to confirm the contents of them.
Note 1: Be sure to install Adjust station first.
Note 2: To perform Destination Data Write for this model, the Adjust manual of the DSC-WX50 series must have been installed.
Install the Adjust manual of the DSC-WX50 series in advance.
(JAPANESE)
これらの機種で調整を行なうには，アジャストマニュアルとアジャストステーションが必要です。
アジャストステーションとは
機種別のアジャストマニュアルを起動するためのソフトウェアです。
アジャストステーションのインストーラと一緒に，インストレーションマニュアルが付いていますので，内容を必ず確認してくださ
い。
アジャストマニュアルとは
デジタルカメラ及びカムコーダのサービス用の調整ソフトウェアで，調整及び各種動作確認を行うことが可能です。
アジャストマニュアルのインストーラと一緒に，インストレーションマニュアルが付いていますので，内容を必ず確認してください。
注意1： インストールは必ずAdjuststationを先に行なってください。
注意2： この機種で仕向け設定を行うには，DSC-WX50シリーズの Adjustmanualがインストールされている必要があ
ります。
 先にDSC-WX50シリーズのAdjustmanualをインストールしてください。