Sony HDC-F950 Manual

HD COLOR CAMERA
HDC-F950
HD CCD BLOCK ADAPTOR
HKC-T950
INSTALLATION AND MAINTENANCE MANUAL
1st Edition
Serial No. 10001 and Higher: HDC-F950
Serial No. 10001 and Higher: HKC-T950

HDC-F950 IMM
!WARNING
This manual is intended for qualified service personnel only.
To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so. Refer all servicing to
qualified service personnel.
!WARNUNG
Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.
Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die
Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei
Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben
Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung
dazu besitzen.
!AVERTISSEMENT
Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin
de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les
réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres.
Pour toute réparation faire appel à une personne compétente uniquement.
For HDC-F950
Laser Diode Properties
Material : In GaAsp
Wave length : 1310 nm, 1550 +4.4 nm
_7.4
Emission duration : Pulse code modulation
Laser output power : _8 dBm
CAUTION
Use of controls or adjustments or performance of
procedures other than those specified herein
may result in hazardous radiation exposure.
For HDC-F950

HDC-F950 IMM 1 (P)
For HDC-F950
Vorsicht!
Explosionsgefahr bei unsachgemäßem Austausch
der Batterie.
Ersatz nur durch denselben oder einen vom
Hersteller empfohlenen ähnlichen Typ. Entsorgung
gebrauchter Batterien nach Angaben des
Herstellers.
ATTENTION
Il y a danger d’explosion s’il y a remplacement
incorrect de la batterie.
Remplacer uniquement avec une batterie du même
type ou d’un type équivalent recommandé par le
constructeur.
Mettre au rebut les batteries usagées conformément
aux instructions du fabricant.
ADVARSEL!
Lithiumbatteri-Eksplosionsfare ved fejlagtig
håndtering.
Udskiftning må kun ske med batteri
af samme fabrikat og type.
Levér det brugte batteri tilbage til leverandøren.
ADVARSEL
Lithiumbatteri - Eksplosjonsfare.
Ved utskifting benyttes kun batteri som
anbefalt av apparatfabrikanten.
Brukt batteri returneres
apparatleverandøren.
VARNING
Explosionsfara vid felaktigt batteribyte.
Använd samma batterityp eller en likvärdig typ
som rekommenderas av apparattillverkaren.
Kassera använt batteri enligt gällande
föreskrifter.
VAROITUS
Paristo voi räjähtää jos se on virheellisesti
asennettu.
Vaihda paristo ainoastaan laitevalmistajan
suosittelemaan tyyppiin.
Hävitä käytetty paristo valmistajan ohjeiden
mukaisesti.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type
recommended by the manufacturer.
Dispose of used batteries according to the
manufacturer’s instructions.

HDC-F950 IMM
For the customers in Japan
For the customers in the Netherlands
Voor de klanten in Nederland
Hoe u de batterijen moet verwijderen, leest u in de
Onderhoudshandleiding.
Gooi de batterij niet weg maar lever deze in als klein
chemisch afval (KCA).
Für Kunden in Deutschland
Entsorgungshinweis: Bitte werfen Sie nur entladene
Batterien in die Sammelboxen beim Handel oder den
Kommunen. Entladen sind Batterien in der Regel dann,
wenn das Gerät abschaltet und signalisiert “Batterie
leer” oder nach längerer Gebrauchsdauer der Batterien
“nicht mehr einwandfrei funktioniert”. Um
sicherzugehen, kleben Sie die Batteriepole z.B. mit
einem Klebestreifen ab oder geben Sie die Batterien
einzeln in einen Plastikbeutel.
For the customers in the U.S.A. and Canada
RECYCLING LITHIUM-ION BATTERIES
Lithium-Ion batteries are recyclable.
You can help preserve our environment
by returning your used rechargeable
batteries to the collection and recycling
location nearest you.
For more information regarding recycling of re-
chargeable batteries, call toll free
1-800-822-8837, or visit http://www.rbrc.org/
Caution: Do not handle damaged or leaking Lithium-Ion
batteries.
2 (P)

1 (E)
HDC-F950 IMM
Table of Contents
Manual Structure
Purpose of this manual ........................................................................................ 3 (E)
Related manuals................................................................................................... 3 (E)
Contents ............................................................................................................... 4 (E)
1. Installation Overview
1-1. Checking the ROM and Software Version............................................ 1-1 (E)
1-2. Connectors and Cables .......................................................................... 1-2 (E)
1-2-1. Connector Input/Output Signals ........................................... 1-2 (E)
1-2-2. Wiring Diagrams for Cables .............................................. 1-10 (E)
1-2-3. Connection Connectors/Cables .......................................... 1-11 (E)
1-2-4. Note in connecting CCU connector ...................................1-11 (E)
1-3. Location of Printed Circuit Boards ..................................................... 1-12 (E)
1-4. Removing/Reinstalling the Side Panel (HDC-F950) ..........................1-14 (E)
1-5. Switch Setting on the Boards ..............................................................1-15 (E)
1-6. Adjusting the Position of the Shoulder Pad (HDC-F950) ...................1-20 (E)
1-7. Installing the Incom Panel Assembly to the Camera Backside
(HDC-F950) ........................................................................................ 1-20 (E)
1-8. Installing the Battery Adaptor BKP-L551 (HDC-F950) .....................1-21 (E)
1-9. Notes on Use of the RTS Kit (HDC-F950) .........................................1-21 (E)
1-10. Disconnecting/Reconnecting Flexible Card Wire ...............................1-22 (E)
2. Service Overview
2-1. Cleaning of Connector/Cable ................................................................ 2-1 (E)
2-2. Cleaning the Vent Portion of the Fan (HDC-F950 only) ...................... 2-3 (E)
2-3. Replacing the Fuse (HDC-F950) ..........................................................2-4 (E)
2-4. Recommended Replacing Parts............................................................. 2-5 (E)
2-4-1. HDC-F950 ............................................................................ 2-5 (E)
2-4-2. HKC-T950 ............................................................................ 2-6 (E)

2 (E) HDC-F950 IMM
3. Setup Menu
3-1. Setup Menu ........................................................................................... 3-1 (E)
3-2. TOP Menu ............................................................................................. 3-3 (E)
3-3. USER Menu .......................................................................................... 3-4 (E)
3-4. USER MENU CUSTOMIZE Menu...................................................... 3-4 (E)
3-5. OPERATION Menu .............................................................................. 3-5 (E)
3-6. PAINT Menu .........................................................................................3-7 (E)
3-7. MAINTENANCE Menu ..................................................................... 3-18 (E)
3-8. FILE Menu .......................................................................................... 3-25 (E)
3-9. DIAGNOSIS Menu ............................................................................. 3-30 (E)
4. File System
4-1. File Structure ......................................................................................... 4-1 (E)
4-2. Operator File ......................................................................................... 4-2 (E)
4-3. Preset Operator File............................................................................... 4-3 (E)
4-4. Scene File .............................................................................................. 4-4 (E)
4-5. Reference Files ...................................................................................... 4-6 (E)
4-6. Lens File ................................................................................................ 4-8 (E)
4-7. OHB File ............................................................................................... 4-9 (E)
4-7-1. Storing the Black Shading and White Shading .................... 4-9 (E)
4-7-2. Adjusting the ND Offset .................................................... 4-10 (E)
4-8. File items ............................................................................................. 4-11 (E)

3 (E)
HDC-F950 IMM
Manual Structure
Purpose of this manual
This manual is the installation and maintenance manual of HD Color Camera HDC-
F950 and HD CCD Block Adaptor HKC-T950 for HDC-F950.
This manual is intended for use by trained system and service engineers, and is
provided information required for the installation and maintenance information .
Related manuals
Besides this installation and maintenance manual, the following manuals are avail-
able.
..
..
.HDC-F950 Operation Manual (Supplied with HDC-F950)
This manual is necessary for the use and the operation of the HDC-F950.
Part No. : 3-789-477-XX
..
..
.HKC-T950 Operation Manual (Supplied with HKC-T950)
This manual is necessary for the installation and operation of the HKC-T950.
Part No. : 3-206-420-XX
..
..
.HDC-F950 e-manual (Tentative name) (Available on request)
This electronic manual intended for use by trained system and service engineers
describes (replacement of main parts, SERVICE menu, electrical alignment,
detailed parts list, block diagrams, schematic diagrams, and board layouts.)
required for parts-level service of the HDC-F950.
For obtaining, contact your local Sony Sales Office/Service Center.
..
..
.System Manual (Available on request)
This manual is necessary for connection and operation of this unit and other
peripheral equipment.
If this manual is required, please contact to your local Sony Sales Office/Service
Center.
..
..
.“Semiconductor Pin Assignments”CD-ROM (Available on request)
This “Semiconductor Pin Assignments” CD-ROM allows you to search for
semiconductors used in B&P Company equipment.
Semiconductors that cannot be searched for on this CD-ROM are listed in the
maintenance manual for the corresponding unit. The maintenance manual contains
a complete list of all semiconductors and their ID Nos., and thus should be used
together with the CD-ROM.
Part number: 9-968-546-XX

4 (E) HDC-F950 IMM
Contents
The installation and maintenance manual is organized by following sections.
Section 1 Installation Overview
This section is described about the information that is required to install (switch
setting on the board, connection information, and the like.) and when installing this
unit.
Section 2 Service Overview
This section is described about the recommended replacing parts, replacing the fuse
and the cleaning procedures.
Section 3 Setup Menu
This section is described about the setup menu (TOP menu, OPERATION menu,
PAINT menu, MAINTENANCE menu, FILE menu and DIAGNOSIS menu).
Section 4 File System
This section is described about the file system to control data.

1-1 (E)
HDC-F950 IMM
Section 1
Installation Overview
1-1. Checking the ROM and Software Version
When connecting the peripheral equipment in the list below to HDC-F950, be sure
to check that the ROM and software version on each peripheral device is corre-
sponding to the camera to be connected.
If the ROM and software version is lower than the specified below, be sure to
perform ROM replacement and updating the software.
If ROM replacement and updating the software are required, contact your local Sony
Sales Office/Service Center.
ROM
Peripheral equipment Board name Ref No. Rom version
MSU-700A/750 CPU-293/CPU-286 IC5, IC6/IC5, IC6 Ver. 1.10 or higher
RCP-720/721 MPU-79 IC10 Ver. 2.73 or higher
RCP-730/731 MPU-79 IC10 Ver. 2.73 or higher
RCP-740/741 MPU-79 IC10 Ver. 2.73 or higher
RCP-700/701 MPU-92 IC6 Ver. 2.73 or higher
RM-B150 CPU-266 IC4 Ver. 1.00 or higher
Software
Peripheral equipment Board name Software version
RCP-750/751 MPU-123 Ver. 1.01 or higher
RM-B750 MPU-124 Ver. 1.00 or higher

1-2 (E) HDC-F950 IMM
!.
!;
8
!,
2
4
!/
!-
!]5
3
![
6!\
9
7
1
!'
!=
*
1-2. Connectors and Cables
1-2-1. Connector Input/Output Signals
HDC-F950 Connector Layout
*: Use 4connector by selecting PROMPTER OUT, GENLOCK IN and RET IN signals with the switch.
PROMPTER OUT signal become effective when the camera is connected to CCU.
GENLOCK IN and RET IN signals become effective when the camera is used alone.
HKC-T950 Connector Layout
@[
@- @= @/
!\
@\
@-
@[
@=
@]

1-3 (E)
HDC-F950 IMM
1
23
4
77
77
7RET CONTROL (6P FEMALE)
(External view)
No. Signal I/O Specifications
1 INCOM 1 IN Zi >10 kZ
MIC ON/OFF ON : GND
OFF : OPEN
2 INCOM 2 IN Zi >10 kZ
MIC ON/OFF ON : GND
OFF : OPEN
3 GND ——
4 NC No connection
5 RET 1 ON/OFF IN Zi >10 kZ
ON : GND
OFF : OPEN
6 RET 2 ON/OFF IN Zi >10 kZ
ON : GND
OFF : OPEN
88
88
8DC OUT (4P FEMALE)
(External view)
No. Signal I/O Specifications
1 GND —— GND for POWER
2 NC No connection
3 NC No connection
4 UNREG OUT +12 V dc 500 mA (max)
Input/Output Signals
11
11
1CCU connector
Based upon BTA S-004A/005A/006A 1.485 Gbps
serial
Output Signals
22
22
2EARPHONE OUT
EARPHONE mini jack
33
33
3TEST OUT
BNC type 75 Z, 1.0 V p-p
44
44
4PROMPTER OUT **
**
*2
BNC type 75 Z, 1.0 V p-p
55
55
5HD SERIAL RET OUT **
**
*1
Based upon BTA-S004A, SMPTE-292M
BNC type 75 Z, 0.8 V p-p 1.485 Gbps
![![
![![
![ HD SERIAL LINK A OUT
Based upon BTA-S004A, SMPTE-372M
BNC type 75 Z, 0.8 V p-p 1.485 Gbps
!]!]
!]!]
!] HD SERIAL LINK B OUT
Based upon BTA-S004A, SMPTE-372M
BNC type 75 Z, 0.8 V p-p 1.485 Gbps
@/@/
@/@/
@/ VIDEO OUT (HKC-T950)
BNC type 75 Z, 1.0 V p-p
Input Signals
44
44
4GENLOCK IN **
**
*2
BNC type 75 Z, 1.0 V p-p
44
44
4RET IN **
**
*2
BNC type 75 Z, 1.0 V p-p
66
66
6Not used
*1 : HD SERIAL RET OUT signal become effective when the camera is
connected to CCU.
*2 : Use this connector by selecting PROMPTER OUT, GENLOCK IN and
RET IN signals with the switch on the rear panel of HDC-F950.
PROMPTER OUT signal become effective when the camera is
connected to CCU.
GENLOCK IN and RET IN signals become effective when the camera is
used alone.

1-4 (E) HDC-F950 IMM
21
3
99
99
9REMOTE (8P FEMALE)
(External view)
No. Signal I/O Specifications
1 TX (+) HDC SERIAL DATA
2 TX (_)
3 RX (+) HDCU/MSU/RCP/CNU/VCS
4 RX (_) SERIAL DATA
5 TX GND —— GND for TX
6 POWER (+) OUT +26 V, 200 mA (max)
7 POWER GND —— GND for POWER (+)
8 VIDEO (X) 75 Z, 1.0 V p-p
CHASSIS GND —— CHASSIS GND
!/!/
!/!/
!/ AUDIO IN CH1/CH2 (3P FEMALE)
(External view)
No. Signal I/O Specifications
1 AUDIO (G) —— _60 dBu, _50 dBu, _40 dBu,
2 AUDIO (X) IN _30 dBu, _20 dBu, selectable
3 AUDIO (Y) IN High impedance, Balanced
(0 dBu = 0.775 Vrms)
!-!-
!-!-
!- INTERCOM CH1/CH2 (5P FEMALE)
(External view)
No. Signal I/O Specifications
1 INCOM MIC (Y) IN _20 dBu (CARBON MIC)
2 INCOM MIC (X) IN _60 dBu (DYNAMIC MIC)
3 GND (INCOM/PGM) ——
4 INCOM OUT 0 dBu
RECEIVE
5 PGM OUT 0 dBu
(0 dBu = 0.775 Vrms)
!=!=
!=!=
!= DC IN (4P MALE)
(External view)
No. Signal I/O Specifications
1 GND —— GND for DC (+)
2 NC No connection
3 NC No connection
4 DC (+)IN+10.5 to 17 V dc

1-5 (E)
HDC-F950 IMM
!\!\
!\!\
!\ LENS (12P FEMALE)
(External view)
No. Signal I/O Specifications
1 RET VIDEO IN ENABLE : 0 V
ENABLE DISABLE : +5 V or OPEN
2 VTR START IN ENABLE : 0 V
/STOP DISABLE : +5 V or OPEN
3 GND —— GND for UNREG
4 AUTO SERVO OUT AUTO : +5 V
MANU : 0 V or OPEN
5 IRIS CONT OUT +3.4 V (F16) to
+6.2 V (F2.8)
6 UNREG OUT +10.5 V to +17 V
7 IRIS POSITION IN +3.4 V (F16) to
+6.2 V (F2.8)
8 AUTO/MANU OUT AUTO IRIS : 0 V
MANUAL IRIS : +5 V
9 EXTENDER IN EX 2 ON : GND
ON/OFF EX 0.8 ON : 30 kZto GND
OFF : OPEN
10 ZOOM IN WIDE : 2 V
POSITION TELE : 7 V
11 FOCUS POSI IN ∞ : 7 V
(/LENS RX) min. : 2 V
12 (LENS TX) OUT
EX 2 ON
30 kΩ
EX 0.8 ON
!;!;
!;!;
!; VF (20P FEMALE)
(External view)
No. Signal I/O Specifications
1 S-DA TA IN/OUT TTL level
2 NC No connection
3 NC No connection
4 SCK OUT TTL level
5 NC No connection
6 NC No connection
7 NC No connection
8 G TALLY OUT ON : 5 V
OFF : GND
9 NC No connection
10 Y VIDEO OUT 1.0 V p-p, Zo = 75 Z
11 NC No connection
12 Y VIDEO OUT 1.0 V p-p, Zo = 75 Z
13 VIDEO GND —— GND for VIDEO
14 Pb VIDEO OUT ±0.35 V p-p, Zo = 75 Z
15 Pr VIDEO OUT ±0.35 V p-p, Zo = 75 Z
16 NC No connection
17 R TALLY OUT ON : 5 V
OFF : GND
18 NC No connection
19 UNREG GND —— GND for UNREG
20 UNREG OUT +10.5 V to +17 V

1-6 (E) HDC-F950 IMM
5
1
2
6
11
16
3
7
12
17
4
8
13
9
14
18
20
19
15
10
1
5
10
11
16
17
18
19
20
2
3
4
!,!,
!,!,
!, TRACKER (FEMALE)
(External view)
No. Signal I/O Specifications
1 TRK R (X) OUT TRACKER RECEIVE
0 dBu unbalanced
2 TRK R (G) —— GND for TRACKER R
3 GND —— GND for UNREG/TALLY
(UNREG/TALLY)
4 R TALLY OUT ON : 5 V (Open Collector)
OFF : 0 V (Open Collector)
5 TRK PGM (G) —— GND for PGM
6 UNREG OUT +12 V (+10.5 to +17.0 V)
7 TRK T (X) IN TRACKER TALK
8 TRK T (Y) IN 0 dBu /_20 dBu
High impedance balanced
9 TRK T (G) —— GND for TRACKER T
10 TRK PGM (X) OUT _20 dBu unbalanced
11 NC No connection
12 G TALLY OUT ON : 5 V (Open Collector)
OFF : 0 V (Open Collector)
13 NC No connection
14 RX_DATA (0) IN TRUNK DATA IN, RS232-C
15 RX_DATA (1) IN
16 NC No connection
17 NC No connection
18 TX_DATA (0) OUT TRUNK DATA OUT, RS232-C
19 TX_DATA (1) OUT
20 GND ——
(0 dBu = 0.775 Vrms)
!'!'
!'!'
!' EXT I/O (20P)
(External view)
No. Signal I/O Specifications
1 Y VIDEO (X) OUT 1.0 V p-p, Zo = 75 Z
2 Y VIDEO (G) —— GND for Y VIDEO
3 PROMPTER (X) OUT 1.0 V p-p, Zo = 75 Z
4 PROMPTER (G) —— GND for PROMPTER
5 Pr VIDEO (X) OUT ±0.35 V p-p, Zo = 75 Z
6 Pr VIDEO (G) —— GND for Pr VIDEO
7 Pb VIDEO (X) OUT ±0.35 V p-p, Zo = 75 Z
8 Pb VIDEO (G) —— GND for Pb VIDEO
9 SDA VF IN/OUT TTL level
10 VD OUT Negative Pulse,
3.0 V p-p, Low impedance
11 CALL ON IN ON : L (0 v)
OFF : H (+3 V)
12 VF POWER OFF OUT ON : H (+5 V)
OFF : L (0 V)
13 MAIN POWER OUT ON : +8 V
ON/OFF OFF : GND
14 SCL VF OUT TTL level
15 TALLY GND —— GND for TALLY
16 BACK TALLY OUT ON : 5 V
OFF : GND
17 PANEL DATA IN RX SERIAL DATA
18 PANEL DATA OUT TX SERIAL DATA
19 VF UNREG +OUT +12 V (+10.5 V to +17.0 V)
20 GND —— GND for UNREG

1-7 (E)
HDC-F950 IMM
5
32
4
11
34
2
5
1
3
2
21
3
21
3
!.!.
!.!.
!. FRONT MIC (3P FEMALE)
(External view)
No. Signal I/O Specifications
1 CHU MIC (G) —— _60 dBu, _50 dBu, _40 dBu,
2 CHU MIC (X) IN _30 dBu, _20 dBu, selectable
3 CHU MIC (Y) IN High impedance, Balanced
(0 dBu = 0.755 Vrms)
@-@-
@-@-
@- MIC (HKC-T950)
(3P FEMALE) (3P MALE)
(External view) (External view)
No. Signal I/O Specifications
1 AUDIO (G) —— _60 dBu, _50 dBu, _40 dBu,
2 AUDIO (X) IN _30 dBu, _20 dBu, selectable
3 AUDIO (Y) IN High impedance, Balanced
(0 dBu = 0.755 Vrms)
@=@=
@=@=
@= INCOM (HKC-T950)
(5P FEMALE) (5P MALE)
(External view) (External view)
No. Signal I/O Specifications
1 INCOM MIC (Y) IN _20 dBu (CARBON MIC)
2 INCOM MIC (X) IN _60 dBu (DYNAMIC MIC)
3 GND (INCOMPGM) ——
4 INCOM RECEIVE OUT 0 dBu
5 PGM OUT 0 dBu
(0 dBu = 0.755 Vrms)

1-8 (E) HDC-F950 IMM
12345
678910
11 12 13 14 15
16 17 18 19 20
45678
12 11 10 9
17 16 15
19
20
14
18
13
123
@[@[
@[@[
@[ VF (HKC-T950)
(20P FEMALE)
(External view)
No. Signal I/O Specifications
1 S DATA IN/OUT TTL level
2 NC No connection
3 NC No connection
4 SCK OUT TTL level
MANU : 0 V or OPEN
5 NC No connection
6 NC No connection
7 NC No connection
8 G TALLY OUT ON : 5 V
OFF : GND
9 NC No connection
10 NC No connection
11 NC No connection
12 Y VIDEO OUT 1.0 V p-p, Zo = 75 Z
13 VIDEO GND —— GND for VIDEO
14 NC No connection
15 NC No connection
16 NC No connection
17 R TALLY OUT ON : 5 V
OFF : GND
18 NC No connection
19 UNREG GND —— GND for UNREG
20 UNREG OUT +10.5 V to +1.7 V
(20P FEMALE)
(External view)
No. Signal I/O Specifications
1 S DATA IN/OUT TTL level
2 NC No connection
3 NC No connection
4 SCK IN TTL level
MANU : 0 V or OPEN
5 NC No connection
6 NC No connection
7 NC No connection
8 G TALLY IN ON : 5 V
OFF : GND
9 NC No connection
10 NC No connection
11 NC No connection
12 Y VIDEO IN 1.0 V p-p, Zi = 75 Z
13 VIDEO GND —— GND for VIDEO
14 NC No connection
15 NC No connection
16 NC No connection
17 R TALLY IN ON : 5 V
OFF : GND
18 NC No connection
19 NC No connection
20 NC No connection

1-9 (E)
HDC-F950 IMM
1
2
3
4A
B
5
6
7
8
9
10
11
12
13
14
15
16
22
17
18
19
20
21
23
24
A
B
123456
78910 11
12 13 14 15 16 22
17
18 19 20 21
23 24
@]@]
@]@]
@] CAM BODY (HKC-T950)
(26P MALE)
(External view)
No. Signal I/O Specifications
A UNREG IN 13 V to 17 V
B UNREG GND —— GND for UNREG
1 OHB H OUT 0.3 V p-p Positive pulse
2 OHB H (G) —— GND for OHB H
3 G VIDEO (G) —— GND for G VIDEO
4 G VIDEO (X) OUT 300 mV p-p, Zo = 75 Z(100 %)
5 R VIDEO (X) OUT 300 mV p-p, Zo = 75 Z(100 %)
6 R VIDEO (G) —— GND for R VIDEO
7 B VIDEO (X) OUT 95 mV p-p, Zo = 75 Z (100 %)
8 B VIDEO (G) —— GND for B VIDEO
9 MIC (X) OUT _60 dBu, _50 dBu, _40 dBu,
10 MIC (Y) OUT _30 dBu, _20 dBu, selectable
11 INCOM/MIC GND —— GND for INCOM/MIC,
CHU F, IRIS CONT
12 IRIS CONT IN +3.4 V (F16) to +6.2 V (F2.8)
13 CHU F IN 0.3 V p-p Positive pulse
14 INCOM RECEIVE IN 0 dBu
15 INCOM MIC (X) OUT _20 dBu (CARBON MIC)
16 INCOM MIC (Y) OUT _60 dBu (DYNAMIC MIC)
17 CHU H IN 150 mV p-p Positive pulse
18 VF VIDEO (X) IN 180 mV p-p, Zi = 75 Z
19 VF VIDEO (G) —— GND for VF VIDEO,CHU H
20 PGM IN 0 dBu
21 RX COMMAND (X) IN
22 RX COMMAND (Y) IN 340 mV p-p
23 TX COMMAND (X) OUT
24 TX COMMAND (Y) OUT
@\@\
@\@\
@\ OPT HEAD (HKC-T950)
(26P FEMALE)
(External view)
No. Signal I/O Specifications
A UNREG OUT 13 V to 17 V
B UNREG GND —— GND for UNREG
1 OHB H IN 0.3 V p-p Positive pulse
2 OHB H (G) —— GND for OHB H
3 G VIDEO (G) —— GND for G VIDEO
4 G VIDEO (X) IN 300 mV p-p, Zi = 75 Z(100 %)
5 R VIDEO (X) IN 300 mV p-p, Zi = 75 Z (100 %)
6 R VIDEO (G) —— GND for R VIDEO
7 B VIDEO (X) IN 95 mV p-p, Zi = 75 Z(100 %)
8 B VIDEO (G) —— GND for B VIDEO
9 MIC (X) IN _60 dBu, _50 dBu, _40 dBu,
10 MIC (Y) IN _30 dBu, _20 dBu, selectable
11 INCOM/MIC GND —— GND for INCOM/MIC,
CHU F, IRIS CONT
12 IRIS CONT OUT +3.4 V (F16) to +6.2 V (F2.8)
13 CHU F OUT 0.3 V p-p Positive pulse
14 INCOM RECEIVE OUT 0 dBu
15 INCOM MIC (X) IN _20 dBu (CARBON MIC)
16 INCOM MIC (Y) IN _60 dBu (DYNAMIC MIC)
17 CHU H OUT 150 mV p-p Positive pulse
18 VF VIDEO (X) OUT 180 mV p-p, Zo = 75 Z
19 VF VIDEO (G) —— GND for VF VIDEO, CHU H
20 PGM OUT 0 dBu
21 RX COMMAND (X) OUT
22 RX COMMAND (Y) OUT 340 mV p-p
23 TX COMMAND (X) IN
24 TX COMMAND (Y) IN

1-10 (E) HDC-F950 IMM
Yellow
Black
White
Red
Red
White
Blue
Red
White
Orange
White
Red
Yellow
White
Black
Blue
Red
Brown
Gray
Red
1-2-2. Wiring Diagrams for Cables
CCA-5 Cable
HDCZ Cable

1-11 (E)
HDC-F950 IMM
1-2-3. Connection Connectors/Cables
Connection made with the connector panels during instal-
lation or service, should be made with the connectors/
complete cable assemblies specified in the following list,
or equivalent parts.
Indication Connection connector/cable
HDC-F950
CCU LEMO®
FUW. 3K. 93C. TLMC96 *4
(HDCU-F950 side)
CAMERA LEMO®
PUW. 3K. 93C. TLCC96 *4
TEST OUT 1-569-370-12 Plug, BNC
PROMPTER OUT
VIDEO OUT
(BNC)
HD SERIAL LINK A/B 1-569-370-12 Plug, BNC or
OUT BELDEN8281 Cable or
HD SERIAL RET OUT equivalent
AUDIO IN 1-508-084-00 XLR, 3P Male or
MIC IN ITT Cannon XLR-3-12C equivalent
(3P FEMALE) Cable assembly
(supplied with HKC-T950, 0.8 m)
1-823-599-11 *3
MIC IN 1-508-083-00 XLR, 3P, Female or
(3P MALE) ITT Cannon XLR-3-11C equivalent
Cable assembly
(supplied with HKC-T950, 0.8 m)
1-823-599-11 *3
RET CONTROL 1-560-078-00 Plug, 6P Male or
(6P FEMALE) HIROSE HR10-7PA-6P equivalent
DC OUT 1-566-425-11 Plug, 4P Male or
(4P FEMALE) HIROSE HR10A-7P-4P equivalent
INTERCOM 1-508-370-11 XLR, 5P Male or
INCOM ITT Cannon XLR-5-12C equivalent
(5P FEMALE) Cable assembly
(supplied with HKC-T950, 0.8 m)
1-823-600-11 *3
INCOM 1-508-363-00 XLR, 5P Female or
(5P MALE) ITT Cannon XLR-5-11C equivalent
Cable assembly
(supplied with HKC-T950, 0.8 m)
1-823-600-11 *3
CAM BODY 1-564-184-00 Plug, 26P Female or
Cable assembly *3
HDCZ-A10
(supplied with HKC-T950, 10 m)
1-823-615-11
HDCZ-A25 (option, 25 m)
1-823-616-11
HDCZ-A50 (option, 50 m)
1-823-617-11
Indication Connection connector/cable
OPT HEAD 1-564-183-31 Plug, 26P Male or
(26P FEMALE) Cable assembly *3
HDCZ-A10
(supplied with HKC-T950, 10 m)
1-823-615-11
HDCZ-A25 (option, 25 m)
1-823-616-11
HDCZ-A50 (option, 50 m)
1-823-617-11
DC IN 1-508-362-00 XLR, 4P Female or
(4P MALE) ITT Cannon XLR-4-11C equivalent, or
Cable assembly 1-551-577-00
(Supplied with AC-550/550CE)
REMOTE 1-766-848-11 Plug, 8P Male or
(8P FEMALE) CCA-5 cable assembly (option) *2
CCA-5-10 (10 m) /CCA-5-3 (3 m) or
REMOTE cable 1-783-372-11
(supplied with RM-B150, 10 m) *1 *2
TRACKER HIROSE HR25-9P-20P equivalent
(20P FEMALE)
VF Cable assembly
(20P FEMALE) (supplied with HKC-T950, 0.7 m)
1-792-603-21
*1: Use of REMOTE cable enables to monitor video signals.
*2: If using a cable of length different from a standard product, contact your
local Sony Sales Office/Service Center.
*3: Only for HKC-T950.
*4: Caution in making the optical/electric signal composite cable:
When making the optical/electric signal composite cable used for this
camera system, the connection connectors specified in this manual
must be used in order to comply with the limits for EMC regulations.
1-2-4. Note in connecting CCU connector
It is recommendable to clean the optical contact portions
mentioned below before connecting this unit to the camera
control unit.
.CCU connector of this unit
.Camera connector of the camera control unit
.Optical/Electrical cable
It is also necessary to clean the optical contact portions
mentioned below before using the HDC-F950 to the large
lens adaptor CA-905L.
.CA cable of a large lens adaptor
.CCU connector of a large lens adaptor
For details on a cleaning method, refer to Section 2-1
“Cleaning of Connector/Cable”.

1-12 (E) HDC-F950 IMM
DAD-38 (Dedicated for HDC-F950)
DPR-241 (Dedicated for HDC-F950)
VA-196A
(Dedicated for HDC-F950)
CN-1964
VDA-55
SG-268
DAP-24
RE-181A
(Dedicated for
HDC-F950)
AU-271
AT-130A *1
(Dedicated for HDC-F950)
SW-1017
SW-1013
SW-1015
SW-1014
DPR-156
RE-188
LP-113
SW-1016
SW-1018
DU-104
CN-1952
CN-1954
CN-2018
CN-1953
SW-1029
RE-184A
(Dedicated for
HDC-F950)
RE-182
SW-2026
RP-114
TG-214
BI-145
NR-73
DR-523
(Dedicated for HDC-F950)
CN-1947
CN-1961
Filter Drive Board
PA-239
DU-69
BI-145
1-3. Location of Printed Circuit Boards
HDC-F950
The circuit boards other than the dedicated boards for
HDC-F950 have compatibility with the circuit boards
installed in HDC-950.
*1: n
The AT-130 board installed in HDC-950 can be used for HDC-F950
by changing the software.